The collected works of computron

hello

i'm looking for a good looking skin for my 4D/20

or for a complete one , in europe

make me an offer

computron

hi

i like to setup a bootp server to do IRIX installation from my win7 PC

how can i do ?

merci

rhôoo

seem to be good !!

merci

it works...... thkx a lot !

i have transfert all my irix's files 3.3, 4.0.1, 4.0.5, 5.1,5.3,6.2,6.5.22 et 6.5.29..... patches ect

DINA rules, thankx

Laurent

Hello

i'l looking for an IRIS 4D/20 complete Skin

i'm in europe

cheers

Eve

hello SAQ

you have one ???

Eve

so sad......

Laurent

Hi

my PI suddently lost his display during using it...... seem to work fine, pass the post test , then beep, but no more display.....
So i look for a GR 1.2 (with VGA connector).

make me an offer please

Evelyne

Hello

I have check the status LED, and i have this combination -O-O, seem to be Interrupt mask test failed..... So not the GR1.2 but the Motherboard....
If you have a Mobo , even a low end, make me an offer !

Eve

Hello

i have check the status led, and i have this combination: *o*o - Interrupt mask test failed

so i think my trouble is about the motherboard ! interup controler dead ?

what is your mind about this ?

Eve

thanks

IP6, i suspect the mobo

i'll do the log tomorow, if i have a PC with serial ports.....

Eve

Merci

Eve

Thank you Jan

My system is a 4d/25 (ip6)

I have a interup controller soldered in the mobo...

Weird

Eve

Hello

I have a spare R4400 250Mhz module for Indigo2

Give me your price or trade with PI parts !

thanks

Eve

Hi

I cannot stay with the idea to do not use my PI anymore, yes i know, i do not switch it on for month (who say years ?), i do not have much time , always working, take care of my sons, my husband etc....

so i try to have a dump on the serial thru hyperterminal., so i plug my cables, unplug the keyboard and switch on.....

and ? i have a display, with a diag, after i had a message because kb is missing, so i switch off, plug the kb and it boot !

now it do a FS check (slow, even with a 15k U320 disc....)

i cross my fingers

Eve

i have talk to fast

so i can have serial acces, and if i unplug the bk, the printenv write me: gfx:dead , no keyboard

if i plug the keyboard, system seem to hand after the post test, all test are passed, but nothing more..... beep and that's all. the test led is off after

Console DUART test PASSED
Memory walking bit test PASSED
Memory address uniqueness test PASSED
Interrupt mask registers test PASSED

Error-- keyboard not responding

Error-- cannot open console "gfx(0)"

initializing tod clock
setting secs=0 min=0 hour=0 day=1 month=1 year=0


System Maintenance Menu

1) Start System
2) Install System Software
3) Run Diagnostics
4) Recover System
5) Enter Command Monitor

Option?

i think i can suspect the keyboard......

Who have a keyboard for me ?

it hang when i ask a hinv via term...... strange ?

Eve

Hi Jan, i have use this system for less than one year, it always show me a tod clock defect....
env are good, console = G, so it might boot, and he had boot today !!! but it hang during FS check

the keyboard was only doing a small "click" sound, no reaction on the screen.

yesterday when i use it, i try to use the shell, and i only have code like [12a] etc instead of caracters, even ctrl+c or nothing work.... then the display switch off......

keyboard ? motherboard ?

i think the chip who read the keybord and mouse is the same for the serial port..... so it seem to be ok as the POST test said

Let me know about your price for the keyboard + shipping !

i'll try to run the diags ! IRIX 3.3 is installed on

Thanks

edit:

some more details.

when i boot up system and go to the prom monitor, the status led are 'runing", when i try a hinv, it stall and the system hang.

i think more and more about a GR1.2 board fail. i stripe it down with BP and ZB boards

Eve

so, some new...

i have config the env to boot without display (console = c) and i unplug the graphics board from to mobo in the emodule.
so it boot on cosole, and now it process with FS check......

keyboard ? gfx subsystem ? i'm a bit lost.

edit:

now i'm loged in.... seem fine , without display !!

The system is ready.



pandora console login: root
IRIX System V Release 3.3.2 pandora
Copyright (c) 1988,1989,1990 Silicon Graphics, Inc.
All Rights Reserved.
You have mail.
TERM = (vt100)
# hinv
1 12 MHZ IP6 Processor
FPU: MIPS R2010A/R3010 VLSI Floating Point Chip Revision: 1.5
CPU: MIPS R2000A/R3000 Processor Chip Revision: 1.6
Data cache size: 8 Kbytes
Instruction cache size: 16 Kbytes
Main memory size: 16 Mbytes
Integral Ethernet controller: Version 0
Integral SCSI controller 0: Version WD33C93
Disk drive: unit 1 on SCSI controller 0
#

Eve

I know , i'm one of them

Eve

Hello

Is it possible to find and buy a Cray CX1..... prices must be serioulsely down now

Eve

ouch the price !!!

Eve

awesome !!!!

can we see it work while playing Turrican on C= 64 ??

Eve

Cool stuff
i love ols sgi advert !

cheers

Eve

you can get Blender 2.47 for Irix..... work fine, and support up to thousand of threads

EVe

i had use an Origin 2000 as render node and an Octane as display for it while using blender

cheers

Eve

is it possible to have a better surface quality ?

it's a bit rought !! no ?

Cheers

Eve

My previous O2k rack was quietter than my Proliant at start !!!

Cheers

Eve

i had tryed a guitar amp simulator , a freeware sources found on an education ftp, it work fine , but the result didn't match my hopes.
not too much latency but sound quality...

i actualy use an Avid product, an Eleven rack, it work so fine !!!

Cheers

Eve

I like to see Blender back on Irix !!

Cheers

Eve

it's a good initiative, but too much generalist.... no tech details or arch analysis.

you totaly omit to talk about SGI history important part : gfx pipe history and evolution !!!!

Cheers

Eve

i think your are doing sweet dreams....

Cheers

Eve

Nice !!!!

Cheers

Eve

commodorejohn wrote: hofner.jpg
Newest member of the family: a Hofner violin bass. (Not sure exactly which model, but it's one of the fully hollow-body ones, not the one with a sustain block inside.) Picked it up because I've been wanting to try one and a guy on Craigslist was offering a good deal since he's in a Beatles cover band and already has two others. It's a bit scuffed up, but overall in good shape, and it sounds sweet as hell Pure bass on the lower strings with a nice woody pluck on the upper ones, plays beautifully, and sounds good even without an amp hooked up

Nice one !!!!

Cheers

Eve

Lol

i have removed a previous post on this topic about horizontal mambo .....

i think we are talking about love marathon ?

Cheers

Eve

baby yeah !!! you are a swinger !!!!

with my husband we swing too

life is not everytime all around computers !!

Cheers

Eve