The collected works of BetXen - Page 1

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of BetXen's lab Indigo2 R4400 250MHz at Feb. 7, 2005, 4:22 a.m...

Hi!

Here are the specs of the Indigo2, R4k250, 128Mb, I'm using at lab.

hinv


Iris Audio Processor: version A2 revision 1.1.0


1 250 MHZ IP22 Processor


FPU: MIPS R4000 Floating Point Coprocessor Revision: 0.0


CPU: MIPS R4400 Processor Chip Revision: 6.0


On-board serial ports: 2


On-board bi-directional parallel port


Data cache size: 16 Kbytes


Instruction cache size: 16 Kbytes


Secondary unified instruction/data cache size: 2 Mbytes on Processor 0


Main memory size: 128 Mbytes


EISA bus: adapter 0


Integral Ethernet: ec0, version 1


Integral SCSI controller 1: Version WD33C93B, revision D


Integral SCSI controller 0: Version WD33C93B, revision D


Disk drive: unit 1 on SCSI controller 0


Graphics board: GU1-Extreme

/usr/gfx/gfxinfo

Code: Select all


Graphics board 0 is "GR2" graphics.


Managed (":0.0") 1280x1024


8 GEs, 2 REs, 24 bitplanes, 4 auxplanes, 4 cidplanes, Z-buffer


GR2 revision 6, VB2.0


HQ2.1 rev A, GE7 rev B,  RE3.1 rev A, VC1 rev B, MC rev C


16" monitor

uname -aR

Code: Select all


IRIX ipesg6 6.2 03131015 IP22

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of A few icons at June 15, 2005, 11:50 p.m...

Thanks a lot for your icons.
Can you please tell me how to link them to my shortcuts on the desktop? I've aleady tried some times ago, but without success, and I don't remember how to do that.

Best regards

Raphaël

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of A few icons at June 17, 2005, 2:30 a.m...

Merci beaucoup!

I'll try this asap.

Raphaël

BetXen
Who joined Sept. 21, 2004, 11:05 a.m.
and authored 239 notes

Wrote on the subject of Open Transport Tycon Deluxe - openTTD for IRIX at Feb. 12, 2006, 3:15 a.m...

Hi

Oh yes, it was a very good game. What a pleasureto find it again. You can find the original files here: http://www.abandonware-france.org/ltf-jeu.php3?id=603

Many old games are available on this site. I've read some times ago that they have asked the creators of the games if they could share them as abandonware... so it seems "legal".

Regards.

Raphaël

_________________
:Onyx2:

4xR12k 400, 8Gb, IR2E, 2x18+3x73GB HD (oxygen)
:A3504L:

16xItanium2 1.6, L2 9MB (neon)
:Fuel:

R16k 800 V12, 2Gb, M-Audio, 36+147GB HD, 3Dconnexion SpaceMouse Classic (nitrogen)
:Octane2:

Dual R14k 600 V6, 2Go, HD (173Go, 34Go) (carbon)
:Octane:

R10k 400 MXE, 1280Mo (lithium) / 2xR10k 300 SSE,... (fluorine)
:O2:

R10k 195, 512Mo (hydrogen) / R5k 180, 512Mo (sodium) / R5k 180->200 motherboard and PM only
:Indigo2IMP:

R10k 195, HighImpact, 160Mo (helium) / R4400 125, Extreme, 160Mo (boron)
:O200:

twin O200, 4xR12k 270, 2Go, HD (4x18Go) (beryllium)
:Indigo:

R4k 100, 80Mo, LG1, 9GB HD, Python 25601 tape (magnesium])
:4D70G:

4D70GT... my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of nekosync-1.2 at Feb. 28, 2006, 2:21 p.m...

Hi

I've just downloaded 1.2-7.1 but can't execute it correctly. The following appears:

Code: Select all


bx_octane 21# ./nekosync.pl


sh: bash:  not found


sh: bash:  not found


sh: bash:  not found


NOTICE: No external configuration file found, using defaults...




Use of uninitialized value in string eq at ./nekosync.pl line 584.


nekosync has not yet been configured - please edit


/etc/nekosync.conf and ensure that sane defaults are set before


re-running.

I've allreeady edited nekosync.conf (with get option), but the two files are in "/_nekoware_tardists_/". Is this a problem?

I can't find the solution by myself. Can you help me?

Thanks in advance. Have a good day.

Raphael

: oxygen (4xR12k400) / :A3504L:

: neon (16xI2 1.6, 9MB L2) / :O200:

: beryllium (4xR12k270)
:Fuel:

: nitrogen (R16k800) / :Octane2:

: carbon (2xR14k600) / :Octane:

: lithium (R10k400) / :Octane:

: fluorine (2xR12k300) / spare 2xR12k360
:O2:

: hydrogen (R10k195) / :O2:

: sodium (R5k180) / :O2:

: R5k180->200 MB and PM only
:Indigo2IMP:

: helium (R10k195, HighImpact) / :Indigo2IMP:

: boron (R4k250)/ :Indigo:

: magnesium (R4k100) / :Indy:

: aluminium (R5k180)
:4D70GT:

4D70GT : my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of nekosync-1.2 at March 1, 2006, 1:32 a.m...

Hello

Thanks a lot for your answers. I'll try this evening.

Just two remarks.

1) The first time I've launched nekosync.pl, it has said to me that the .conf was not edited/configured. Actually it was, but I had forgotten to set "configured=TRUE". Nekosync.conf wasn't in /usr/nekoware/etc but the perl found it here "without problems" the next time. Strange...

2) In the .conf file, one can find

Code: Select all


$rsync = "/usr/neokware/bin/rsync";

instead of

Code: Select all


$rsync = "/usr/nekoware/bin/rsync";

Thanks again. Best regards.

Raphaël

: oxygen (4xR12k400) / :A3504L:

: neon (16xI2 1.6, 9MB L2) / :O200:

: beryllium (4xR12k270)
:Fuel:

: nitrogen (R16k800) / :Octane2:

: carbon (2xR14k600) / :Octane:

: lithium (R10k400) / :Octane:

: fluorine (2xR12k300) / spare 2xR12k360
:O2:

: hydrogen (R10k195) / :O2:

: sodium (R5k180) / :O2:

: R5k180->200 MB and PM only
:Indigo2IMP:

: helium (R10k195, HighImpact) / :Indigo2IMP:

: boron (R4k250)/ :Indigo:

: magnesium (R4k100) / :Indy:

: aluminium (R5k180)
:4D70GT:

4D70GT : my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Blonay, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of Nekoware-mips3 at April 29, 2006, 5:45 a.m...

What a good idea!

I will probably get an Indy and an Indigo soon. And the box I'm working on quite everyday is a R4400 Indigo2. Do you plan to compile the latest version of rsync too?

I wish we'll have fun with all these boxes sleeping in many corners...

Regards.

Raphaël

: oxygen (4xR12k400) / :A3504L:

: neon (16xI2 1.6, 9MB L2) / :O200:

: beryllium (4xR12k270)
:Fuel:

: nitrogen (R16k800) / :Octane2:

: carbon (2xR14k600) / :Octane:

: lithium (R10k400) / :Octane:

: fluorine (2xR12k300) / spare 2xR12k360
:O2:

: hydrogen (R10k195) / :O2:

: sodium (R5k180) / :O2:

: R5k180->200 MB and PM only
:Indigo2IMP:

: helium (R10k195, HighImpact) / :Indigo2IMP:

: boron (R4k250)/ :Indigo:

: magnesium (R4k100) / :Indy:

: aluminium (R5k180)
:4D70GT:

4D70GT : my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Blonay, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of Nekoware-mips3 at April 29, 2006, 12:50 p.m...

Thanks a lot in advance...

Have a good day.

Raphaël

: oxygen (4xR12k400) / :A3504L:

: neon (16xI2 1.6, 9MB L2) / :O200:

: beryllium (4xR12k270)
:Fuel:

: nitrogen (R16k800) / :Octane2:

: carbon (2xR14k600) / :Octane:

: lithium (R10k400) / :Octane:

: fluorine (2xR12k300) / spare 2xR12k360
:O2:

: hydrogen (R10k195) / :O2:

: sodium (R5k180) / :O2:

: R5k180->200 MB and PM only
:Indigo2IMP:

: helium (R10k195, HighImpact) / :Indigo2IMP:

: boron (R4k250)/ :Indigo:

: magnesium (R4k100) / :Indy:

: aluminium (R5k180)
:4D70GT:

4D70GT : my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Blonay, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of Commented script to CLONE ROOT DISK at Sept. 8, 2006, 5:12 a.m...

Hi guys!

As I sometimes need to clone a root disk for backup purpose, I've read all your posts concerning this subject (e.g. viewtopic.php?t=8619 ) and tried to write my own script. The previous disk of the Indigo2 I'm using at work crashed, the only backup (bru) was done some 2 years ago and the file was corrupted. I had to reinstall everything from scratch: Irix, additional hardware, special software,...

The problem is that I don't know enough about shell scripts... :wink:

. So, I've used foetz's one and modified it to include some options one could find usefull and - that's the most important part in my point of view - many comments to help beginners understand faster what the script does and geeks remember how to do it. I hope we'll all find here a reference for performing this cloning procedure.

Please feel free to use and modify it as your convenience. If you think some modifications would be usefull for many people, you can send me your script and I will try to include your improvements.

The following code will be updated with latest revisions when available (I hope so...).

last revision: 2006.09.09

Code: Select all


#!/sbin/ksh


#


#  auto xfs root disk duplicating


#  IRIX 6.2 or higher


#  26.04.2000 by R-A-C


#


#  modified by BetXen 2006.09.09


#


#  for more informations, see http://forums.nekochan.net/viewtopic.php?p=87120


#


#


#  LAST REVISION: 2006.09.09


#


#


#  ************************


#  * GENERAL INFORMATION: *


#  ************************


#


#  This script duplicates any xfs root disk onto another one using the


#  xfsdump/xfsrestore method. The target disk doesn't need to be greater or


#  equal in size than the source one. The free space should simply be big


#  enough to contain all the data of the first disk.


#


#  USAGE: scriptname (orig. disk cntrl) (orig. disk id) (target disk cntrl)...


#  (target disk id)


#  e.g. sgi_clone_root_disk 0 1 1 3 (will duplicate disk on scsi controller 0,


#  device id1 onto target disk on scsi controller 1 (i.e. external disk),


#  device id3)


#


#  If you copy/paste this text in a text editor, don't forget to chmod the


#  saved file to make it executable. Moreover, as it's a


#  system task, it should only be executed by root:


#       su


#   chown root:0 ./<name_of_your_script>


#   chmod a-x ./<name_of_your_script>


#   chmod u+x ./<name_of_your_script>


#


#  In order to be executed without the intervention of the user, the script


#  doesn't ask you for choices (e.g. spacecheck or not). If you want to


#  enable/disable it, please edit the script and uncomment/comment the


#  dedicated lines.


#


#  DON'T FORGET to partition the target disk as root drive at least once


#  before running the script. If you don't know how to perform this, please


#  follow these steps in your prefered shell:


#       fx


#       (enter)


#       <your_disk_controller_number>


#       <your_disk_drive_number>


#       (enter)


#       r


#       ro


#       (enter)


#       yes


#       ..


#       l


#       s


#       a


#       ..


#       ..


#       exi


#




export orig_cntrl=$1


export orig_drv=$2


export target_cntrl=$3


export target_drv=$4




clear




if [[ $# != 4 ]]; then


print "STOP! Bad number of arguments"


print "usage: scriptname (orig. disk cntrl) (orig. disk id) (target disk cntrl) (target disk id)"


print ""


print "example: sgi_clone_root_disk 0 1 1 3"


print ""


exit 1




elif [[ ${target_cntrl} = 0  &&  ${target_drv} = 1 ]]; then


print ""


print "STOP! Target drive is dks0d1..."


print "Isn't it your root drive?"


print "If you really want to do this, please edit the script..."


print ""


exit 1




elif [[ ${orig_cntrl} = ${target_cntrl}  &&  ${orig_drv} = ${target_drv} ]]; then


print ""


print "STOP! Original disk same as target disk..."


print ""


exit 1




else


print ""


print "***************************"


print "* ... formatting disk ... *"


print "***************************"


print ""


mkfs /dev/rdsk/dks${target_cntrl}d${target_drv}s0




print ""


print "*************************"


print "* ... mounting disk ... *"


print "*************************"


print ""


mkdir /sgi_clone_dsk_tmp


mount /dev/dsk/dks${target_cntrl}d${target_drv}s0 /sgi_clone_dsk_tmp




#  Uncomment the next lines if you want the script to inform you about available


#  space on the destination disk. Would take time, but could be usefull if you


#  have a smaller disk.


#


#   print ""


#   print "***********************************************************"


#   print "* ... giving size infos (in terms of 1024-byte blocks)... *"


#   print "***********************************************************"


#   print ""


#   print "Disk usage of /:"


#   du -k -s /


#   print ""


#   print "Free space on target disk:"


#   df -k /dev/dsk/dks${target_cntrl}d${target_drv}s0


#   print ""


#   print "     PLEASE CHECK SPACE!"


#   print "     Sleeping 15 seconds to let you abort script..."


#   sleep 15




print ""


print "************************************"


print "* ... duplicating data content ... *"


print "************************************"


print ""


print "Informations will be given every 30 seconds."


print ""


cd /sgi_clone_dsk_tmp


#  If you don't want infos during the process, remove "-p 30" in the next line.


timex xfsdump -l 0 -p 30 - / | xfsrestore - .




print ""


print "*****************************"


print "* ... making boot stuff ... *"


print "*****************************"


print ""


cd /stand


dvhtool -v get sash sash /dev/rdsk/dks${orig_cntrl}d${orig_drv}vh


dvhtool -v get ide ide /dev/rdsk/dks${orig_cntrl}d${orig_drv}vh


dvhtool -v creat sash sash /dev/rdsk/dks${target_cntrl}d${target_drv}vh


dvhtool -v creat ide ide /dev/rdsk/dks${target_cntrl}d${target_drv}vh




#  Uncomment the next lines if you plan to use this script as a backup one and


#  to write a file containing the date and time on your disks' root folder.


#   print ""


#   print "***************************************************"


#   print "* ... writing /_LAST_CLONE_.txt on both disks ... *"


#   print "***************************************************"


#   print ""


#   echo "Last clone using sgi_clone_disk script made on " > /_LAST_CLONE_.txt


#   date >> /_LAST_CLONE_.txt


#   more /_LAST_CLONE_.txt > /sgi_clone_dsk_tmp/_LAST_CLONE_.txt




print ""


print "**********************"


print "* ... unmounting ... *"


print "**********************"


print ""


cd /


umount /sgi_clone_dsk_tmp


sleep 1


rm -rf /sgi_clone_dsk_tmp




print ""


print "****************"


print "* ... done ... *"


print "****************"


print ""




fi


exit 0

foetz, thanks a lot for your help!

Raphaël[/b]

: oxygen (4xR12k400) / :A3504L:

: neon (16xI2 1.6, 9MB L2) / :O200:

: beryllium (4xR12k270)
:Fuel:

: nitrogen (R16k800) / :Octane2:

: carbon (2xR14k600) / :Octane:

: lithium (R10k400) / :Octane:

: fluorine (2xR12k300) / spare 2xR12k360
:O2:

: hydrogen (R10k195) / :O2:

: sodium (R5k180) / :O2:

: R5k180->200 MB and PM only
:Indigo2IMP:

: helium (R10k195, HighImpact) / :Indigo2IMP:

: boron (R4k250)/ :Indigo:

: magnesium (R4k100) / :Indy:

: aluminium (R5k180)
:4D70GT:

4D70GT : my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Blonay, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of Commented script to CLONE ROOT DISK at Sept. 9, 2006, 1:07 a.m...

script updated: 2006.09.09

- comment added concerning chown/chmod in order the script to be executed only by root.

Raphaël

: oxygen (4xR12k400) / :A3504L:

: neon (16xI2 1.6, 9MB L2) / :O200:

: beryllium (4xR12k270)
:Fuel:

: nitrogen (R16k800) / :Octane2:

: carbon (2xR14k600) / :Octane:

: lithium (R10k400) / :Octane:

: fluorine (2xR12k300) / spare 2xR12k360
:O2:

: hydrogen (R10k195) / :O2:

: sodium (R5k180) / :O2:

: R5k180->200 MB and PM only
:Indigo2IMP:

: helium (R10k195, HighImpact) / :Indigo2IMP:

: boron (R4k250)/ :Indigo:

: magnesium (R4k100) / :Indy:

: aluminium (R5k180)
:4D70GT:

4D70GT : my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Blonay, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of Sgi still alive ? at Nov. 29, 2010, 8:19 a.m...

Hi folks !

I've just found something that would probably make you smile:
http://pctop.ch/partage/F_TECH/B08E27.pdf

Have a look at the computers and display pics... Is one of you working for this company ? Ahhh, nostalgy...!

: oxygen (4xR12k400) / :A3504L:

: neon (16xI2 1.6, 9MB L2) / :O200:

: beryllium (4xR12k270)
:Fuel:

: nitrogen (R16k800) / :Octane2:

: carbon (2xR14k600) / :Octane:

: lithium (R10k400) / :Octane:

: fluorine (2xR12k300) / spare 2xR12k360
:O2:

: hydrogen (R10k195) / :O2:

: sodium (R5k180) / :O2:

: R5k180->200 MB and PM only
:Indigo2IMP:

: helium (R10k195, HighImpact) / :Indigo2IMP:

: boron (R4k250)/ :Indigo:

: magnesium (R4k100) / :Indy:

: aluminium (R5k180)
:4D70GT:

4D70GT : my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
Who joined Sept. 21, 2004, 11:05 a.m.
and authored 239 notes

Wrote on the subject of Octane2: 2xR14k 600, 2Gb, V6 at Jan. 7, 2011, 3:13 p.m...

Hi again !

Here is my "new" Octane2. In fact I received it quite one year ago but didn't found time to play with very often up to now. I hope it will change...

Code:

hinv -vm

Location: /hw/node

PM10360MHZ Board: barcode KXS952     part 030-1590-001 rev  B

Location: /hw/node/xtalk/15

IP30 Board: barcode KSX636     part 030-1467-001 rev  D

Location: /hw/node/xtalk/15/pci/2

PWR.SPPLY.ER Board: barcode AAE0010025 part 060-0035-002 rev  A

FP1 Board: barcode KSN772     part 030-0891-003 rev  G

Location: /hw/node/xtalk/11

ODY32 Board: barcode KXS098     part 030-1403-003 rev  A

1 360 MHZ IP30 Processor

Heart ASIC: Revision F

CPU: MIPS R12000 Processor Chip Revision: 3.5

FPU: MIPS R12010 Floating Point Chip Revision: 0.0

Main memory size: 2048 Mbytes

Xbow ASIC: Revision 1.4

Instruction cache size: 32 Kbytes

Data cache size: 32 Kbytes

Secondary unified instruction/data cache size: 2 Mbytes

Integral SCSI controller 0: Version QL1040B (rev. 2), single ended

Disk drive: unit 1 on SCSI controller 0 (unit 1)

Disk drive: unit 2 on SCSI controller 0 (unit 2)

Integral SCSI controller 1: Version QL1040B (rev. 2), single ended

IOC3/IOC4 serial port: tty1

IOC3/IOC4 serial port: tty2

IOC3 parallel port: plp1

Graphics board: V6

Integral Fast Ethernet: ef0, version 1, pci 2

Iris Audio Processor: version RAD revision 12.0, number 1

PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2

PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0

PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1

PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 3

Code:

/usr/gfx/gfxinfo -v

Graphics board 0 is "ODYSSEY" graphics.

Managed (":0.0") 1280x1024

BUZZ version A.1

PB&J version 1

32MB memory

Banks: 2, CAS latency: 3

Monitor 0 type: Unknown

Input Sync: Voltage - Video Level; Source - Internal; Genlocked - False

Channel 0:

Origin = (0,0)

Video Output: 1280 pixels, 1024 lines, 96.04Hz (1280x1024_96)

Video Format Flags:  (none)

Sync Disabled

Using Gamma Map 0

Code:

uname -aR

IRIX64 bx_octane2 6.5 6.5.29f 01090133 IP30

/code]

[code]scsicontrol -i /dev/scsi/*

/dev/scsi/sc0d1l0:  Disk          SEAGATE SX1181677LCV    C00C

ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing

Device is  ready

/dev/scsi/sc0d2l0:  Disk          SEAGATE ST336704LC      0003

ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing

Device is  ready

[/code]

[code]/sbin/diskpatch -v

sc0d1l0:  Disk         SEAGATE SX1181677LCV    C00C  Serial: 3EM0CB4W

sc0d2l0:  Disk         SEAGATE ST336704LC      0003  Serial: 3CD07R2B

_________________
:Onyx2:

4xR12k 400, 8Gb, IR2E, 2x18+3x73GB HD (oxygen)
:A3504L:

16xItanium2 1.6, L2 9MB (neon)
:Fuel:

R16k 800 V12, 2Gb, M-Audio, 36+147GB HD, 3Dconnexion SpaceMouse Classic (nitrogen)
:Octane2:

Dual R14k 600 V6, 2Go, HD (173Go, 34Go) (carbon)
:Octane:

R10k 400 MXE, 1280Mo (lithium) / 2xR10k 300 SSE,... (fluorine)
:O2:

R10k 195, 512Mo (hydrogen) / R5k 180, 512Mo (sodium) / R5k 180->200 motherboard and PM only
:Indigo2IMP:

R10k 195, HighImpact, 160Mo (helium) / R4400 125, Extreme, 160Mo (boron)
:O200:

twin O200, 4xR12k 270, 2Go, HD (4x18Go) (beryllium)
:Indigo:

R4k 100, 80Mo, LG1, 9GB HD, Python 25601 tape (magnesium])
:4D70G:

4D70GT... my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of Twin Origin200: 4xR12K 270MHz, 2GB, headless at Jan. 10, 2011, 11:47 p.m...

Here is another hinv topic.
I received this two-tower Origin200 one year ago but didn't have time to play with till now. Just fired it up yesterday to (re)discover what's inside...

hinv -mv

Code: Select all


Location: /hw/module/1/slot/MotherBoard/node


PIMM_270_4M_2P Board: barcode JHA773     part 013-2511-001 rev  C


Location: /hw/module/1/slot/MotherBoard/node/xtalk/8


IP29 Board: barcode JHH021     part 030-1389-001 rev  B


Location: /hw/module/1/slot/MotherBoard/node/xtalk/8/pci/2


Location: /hw/module/2/slot/MotherBoard/node


PIMM_270_4M_2P Board: barcode JGW704     part 013-2511-001 rev  C


Location: /hw/module/2/slot/MotherBoard/node/xtalk/8


IP29 Board: barcode JGW381     part 030-1389-001 rev  B


Location: /hw/module/2/slot/MotherBoard/node/xtalk/8/pci/2


4 270 MHZ IP27 Processors


CPU: MIPS R12000 Processor Chip Revision: 2.3


FPU: MIPS R12010 Floating Point Chip Revision: 0.0


CPU 0 at Module 1/Slot 1/Slice A: 270 Mhz MIPS R12000 Processor Chip (enabled)


Processor revision: 2.3. Secondary cache: Size 4 MB Speed 180 Mhz


CPU 1 at Module 1/Slot 1/Slice B: 270 Mhz MIPS R12000 Processor Chip (enabled)


Processor revision: 2.3. Secondary cache: Size 4 MB Speed 180 Mhz


CPU 2 at Module 2/Slot 2/Slice A: 270 Mhz MIPS R12000 Processor Chip (enabled)


Processor revision: 2.3. Secondary cache: Size 4 MB Speed 180 Mhz


CPU 3 at Module 2/Slot 2/Slice B: 270 Mhz MIPS R12000 Processor Chip (enabled)


Processor revision: 2.3. Secondary cache: Size 4 MB Speed 180 Mhz


Main memory size: 2048 Mbytes


Instruction cache size: 32 Kbytes


Data cache size: 32 Kbytes


Secondary unified instruction/data cache size: 4 Mbytes


Memory at Module 1/Slot 1: 1024 MB (enabled)


Bank 0 contains 512 MB (Standard) DIMMS (enabled)


Bank 1 contains 512 MB (Standard) DIMMS (enabled)


Memory at Module 2/Slot 2: 1024 MB (enabled)


Bank 0 contains 512 MB (Standard) DIMMS (enabled)


Bank 1 contains 512 MB (Standard) DIMMS (enabled)


Integral SCSI controller 0: Version QL1040B (rev. 2), single ended


Disk drive: unit 1 on SCSI controller 0


Disk drive: unit 2 on SCSI controller 0


Disk drive: unit 3 on SCSI controller 0


Integral SCSI controller 2: Version QL1040B (rev. 2), single ended


Disk drive: unit 1 on SCSI controller 2


Integral SCSI controller 3: Version QL1040B (rev. 2), single ended


Integral SCSI controller 1: Version QL1040B (rev. 2), single ended


IOC3 serial port: tty1


IOC3 serial port: tty3


IOC3 serial port: tty2


IOC3 serial port: tty4


IOC3 parallel port: plp1


IOC3 parallel port: plp2


Integral Fast Ethernet: ef0, version 1, module 1, slot MotherBoard, pci 2


Fast Ethernet: ef1, version 1, module 2, slot MotherBoard, pci 2


Origin 200 base I/O, module 1 slot 1


Origin 200 base I/O, module 2 slot 2


PCI Adapter ID (vendor 4265, device 3) pci slot 2


PCI Adapter ID (vendor 4215, device 4128) pci slot 0


PCI Adapter ID (vendor 4215, device 4128) pci slot 1


PCI Adapter ID (vendor 4265, device 3) pci slot 2


PCI Adapter ID (vendor 4215, device 4128) pci slot 0


PCI Adapter ID (vendor 4215, device 4128) pci slot 1


IOC3 external interrupts: 1


IOC3 external interrupts: 2


HUB in Module 1/Slot 1: Revision 5 Speed 90.00 Mhz (enabled)


HUB in Module 2/Slot 2: Revision 5 Speed 90.00 Mhz (enabled)


IP27prom in Module 1/Slot n1: Revision 6.27


IP27prom in Module 2/Slot n2: Revision 6.27

uname -aR

Code: Select all


IRIX64 masg64 6.5 6.5.4f 04151556 IP27

scsicontrol -i /dev/scsi/*

Code: Select all


/dev/scsi/sc0d1l0:  Disk          SGI     IBM  DGHS18Y    0190


ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds


cmdqueing


Device is  ready


/dev/scsi/sc0d2l0:  Disk          SGI     IBM  DGHS18Y    0190


ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds


cmdqueing


Device is  ready


/dev/scsi/sc0d3l0:  Disk          SGI     IBM  DGHS18Y    0190


ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds


cmdqueing


Device is  ready


/dev/scsi/sc2d1l0:  Disk          SGI     IBM  DGHS18Y    0190


ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds


cmdqueing


Device is  ready

/sbin/diskpatch -v

Code: Select all


sc0d1l0:  Disk         SGI     IBM  DGHS18Y    0190  Serial: 68165D2E


sc2d1l0:  Disk         SGI     IBM  DGHS18Y    0190  Serial: 68163B8B


sc0d2l0:  Disk         SGI     IBM  DGHS18Y    0190  Serial: 68163241


sc0d3l0:  Disk         SGI     IBM  DGHS18Y    0190  Serial: 681641CC

I would like to reinstall or update IRIX. Do I have something to know before (like patch5086, last version of IRIX that supports O200, additional CD required,...) ?

Thanks in advance for you help.

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of Twin Origin200: 4xR12K 270MHz, 2GB, headless at Jan. 11, 2011, 2:23 a.m...

Thanks for your answers.

I have hoever some more questions:
- So, if I boot from CD, the patch is installed automatically ?
- The CD drive can be connected on any of the two towers, even if I install from the miniroot ?
- If I decided to reinstall completely the system, could I do it when the two towers are connected or should I do it separetely and connect them afterwards ?
- Last question, for now: how can I keep the licenses if I reinstall irix ? Which file(s) to copy on my backup server ?

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of Twin Origin200: 4xR12K 270MHz, 2GB, headless at Jan. 11, 2011, 2:44 p.m...

I don't have enough time to play with my boxes, so I won't probably add a graphic card to that one. For sure, the origin 200 is the loudest that I own. In fact it's located in the basement of my parent's house... I only fire it up from time to time

I'll focus on my octane2 for the time being... and play with the others when I can't do anything else, that means when it rains ;-)

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Blonay, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of [Poll] Which do we have more of singles or multiprocessors? at March 1, 2011, 11:50 p.m...

Voted for singles, but in fact I have 4 uniprocessors and 1 four-processors...
Processors-count, nobody wins, 50:50 (very swiss indeed, compromise culture

)

: oxygen (4xR12k400) / :A3504L:

: neon (16xI2 1.6, 9MB L2) / :O200:

: beryllium (4xR12k270)
:Fuel:

: nitrogen (R16k800) / :Octane2:

: carbon (2xR14k600) / :Octane:

: lithium (R10k400) / :Octane:

: fluorine (2xR12k300) / spare 2xR12k360
:O2:

: hydrogen (R10k195) / :O2:

: sodium (R5k180) / :O2:

: R5k180->200 MB and PM only
:Indigo2IMP:

: helium (R10k195, HighImpact) / :Indigo2IMP:

: boron (R4k250)/ :Indigo:

: magnesium (R4k100) / :Indy:

: aluminium (R5k180)
:4D70GT:

4D70GT : my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of Cool (open source) software you would like to see ported... at March 18, 2011, 1:51 a.m...

Hi folks.

I'm trying to find some graphical disk usage analyzer which could draw tree maps.

I've found xdiskusage but it seems that the areas are not proportional to the real size of the folders. There are other softs too. Baobab looks good, but sources are not available. jdiskreport can display pie-charts but no tree maps.

My favourite (on the dark side of the force... windows) is spacemonger : simple but efficient. Do you know about a similar soft for irix, or that would compile quite easily ?

Thanks in advance for your answers.

BetXen

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of WHat do we all do (occupation)? at March 25, 2011, 1:53 a.m...

PhD until 2009, then unemployed quite one year. Hired as CAD-man in the R&D department of a pharmaceutical company for 2 months, then as test & characterization engineer and finally, since one week, as a R&D project leader.

: oxygen (4xR12k400) / :A3504L:

: neon (16xI2 1.6, 9MB L2) / :O200:

: beryllium (4xR12k270)
:Fuel:

: nitrogen (R16k800) / :Octane2:

: carbon (2xR14k600) / :Octane:

: lithium (R10k400) / :Octane:

: fluorine (2xR12k300) / spare 2xR12k360
:O2:

: hydrogen (R10k195) / :O2:

: sodium (R5k180) / :O2:

: R5k180->200 MB and PM only
:Indigo2IMP:

: helium (R10k195, HighImpact) / :Indigo2IMP:

: boron (R4k250)/ :Indigo:

: magnesium (R4k100) / :Indy:

: aluminium (R5k180)
:4D70GT:

4D70GT : my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of WHat do we all do (occupation)? at March 26, 2011, 5:39 a.m...

duck wrote:

theinonen wrote: It seems I am the only one not working with computers for living.

Nope, I was way up there as the first reply...

Not working with computers for living too...

: oxygen (4xR12k400) / :A3504L:

: neon (16xI2 1.6, 9MB L2) / :O200:

: beryllium (4xR12k270)
:Fuel:

: nitrogen (R16k800) / :Octane2:

: carbon (2xR14k600) / :Octane:

: lithium (R10k400) / :Octane:

: fluorine (2xR12k300) / spare 2xR12k360
:O2:

: hydrogen (R10k195) / :O2:

: sodium (R5k180) / :O2:

: R5k180->200 MB and PM only
:Indigo2IMP:

: helium (R10k195, HighImpact) / :Indigo2IMP:

: boron (R4k250)/ :Indigo:

: magnesium (R4k100) / :Indy:

: aluminium (R5k180)
:4D70GT:

4D70GT : my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Blonay, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of WHat do we all do (occupation)? at March 31, 2011, 5:32 a.m...

Don't be so afraid C-E... During my thesis I didn't know what I wanted to do in my real life either. I learned physics and finally work as PM in a pharmaceutical company. Nothing related. During your thesis, you learn how to manage a scientific project and to think globally. That's already a good starting point. You'll learn your specific job on the go.

: oxygen (4xR12k400) / :A3504L:

: neon (16xI2 1.6, 9MB L2) / :O200:

: beryllium (4xR12k270)
:Fuel:

: nitrogen (R16k800) / :Octane2:

: carbon (2xR14k600) / :Octane:

: lithium (R10k400) / :Octane:

: fluorine (2xR12k300) / spare 2xR12k360
:O2:

: hydrogen (R10k195) / :O2:

: sodium (R5k180) / :O2:

: R5k180->200 MB and PM only
:Indigo2IMP:

: helium (R10k195, HighImpact) / :Indigo2IMP:

: boron (R4k250)/ :Indigo:

: magnesium (R4k100) / :Indy:

: aluminium (R5k180)
:4D70GT:

4D70GT : my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
Who joined Sept. 21, 2004, 11:05 a.m.
and authored 229 notes

Wrote on the subject of Happy Easter Nekochaners at April 26, 2011, 12:11 a.m...

A little bit late... Happy Easter to all of you nekochaners !

_________________
:Onyx2:

4xR12k 400, 8Gb, IR2E, 2x18+3x73GB HD
:A3504L:

16xItanium2 1.6, L2 9MB
:Fuel:

R16k 800 V12, 2Gb, M-Audio, 36+147GB HD, 3Dconnexion SpaceMouse Classic
:Octane2:

Dual R14k 600 V6, 2Go, HD (173Go, 34Go)
:Octane:

R10k 400 MXE, 1280Mo / 2xR10k 300 SSE,...
:O2:

R10k 195, 512Mo / R5k 180, 512Mo / R5k 180->200 motherboard and PM only
:Indigo2IMP:

R10k 195, HighImpact, 160Mo/ R4400 125, Extreme, 160Mo
:O200:

twin O200, 4xR12k 270, 2Go, HD (4x18Go)
:4D70G:

4D70GT... my very first one (now property of musée bolo and the foundation mémoires informatiques )

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of Fuel: R16k 800, 2Gb, V10, M-Audio, 36+147GB HD at May 3, 2011, 2:35 p.m...

EDITED 12.01.2012: V10 replaced by V12

After so many years I finally decided to buy a fuel. Hopefully Ian, as always, had lots of machines available at a very reasonable price. Moreover, he put so much care in the preparation, personalisation, packing and shipping of it that I'm fully satisfied. If you would like a new box working like a charm, he is definitely the guy you should contact. Thanks again for all, Ian.

I didn't found enough time up to now to discover every personalisation and gift he included... but I will have soon. I'm really looking forward to playing with it. It's such a nice machine.

Let's have a look at its outputs right now !

hinv -mv

Code: Select all


Location: /hw/module/001c01/node


IP34 Board: barcode NCJ712     part 030-1707-004 rev -C


Location: /hw/module/001c01/node/cpubus/0


IP34PIMM Board: barcode NNN514     part 030-1932-001 rev -B


###Location: /hw/module/001c01/Ibrick/xtalk/13


###       ASTODYV10 Board: barcode NSR498     part 030-1826-003 rev -A


Location: /hw/module/001c01/Ibrick/xtalk/13


ASTODY Board: barcode MLD922     part 030-1726-003 rev -E


Location: /hw/module/001c01/Ibrick/xtalk/14


IP34 Board: barcode NCJ712     part 030-1707-004 rev -C


Location: /hw/module/001c01/Ibrick/xtalk/15


IP34 Board: barcode NCJ712     part 030-1707-004 rev -C


1 800 MHZ IP35 Processor


CPU: MIPS R16000 Processor Chip Revision: 2.2


FPU: MIPS R16010 Floating Point Chip Revision: 2.2


CPU 0 at Module 001c01/Slot 0/Slice A: 800 Mhz MIPS R16000 Processor Chip (enabled)


Processor revision: 2.2. Scache: Size 4 MB Speed 400 Mhz  Tap 0xa


Main memory size: 2048 Mbytes


Instruction cache size: 32 Kbytes


Data cache size: 32 Kbytes


Secondary unified instruction/data cache size: 4 Mbytes


Memory at Module 001c01/Slot 0: 2048 MB (enabled)


Bank 0 contains 1024 MB (Premium) DIMMS (enabled)


Bank 1 contains 1024 MB (Premium) DIMMS (enabled)


Integral SCSI controller 2: Version QL1280, low voltage differential


Integral SCSI controller 3: Version QL1280, low voltage differential


Integral SCSI controller 0: Version QL12160, low voltage differential


Disk drive: unit 1 on SCSI controller 0 (unit 1)


Disk drive: unit 2 on SCSI controller 0 (unit 2)


Integral SCSI controller 1: Version QL12160, single ended


CDROM: unit 4 on SCSI controller 1


IOC3/IOC4 serial port: tty1


IOC3/IOC4 serial port: tty2


IOC3 parallel port: plp1


###Graphics board: V10


Graphics board: V12


Integral Fast Ethernet: ef0, version 1, module 001c01, pci 4


Iris Audio Processor: version MAD revision 1, number 1


PCI Adapter ID (vendor 0x1077, device 0x1280) PCI slot 1


PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1


PCI Adapter ID (vendor 0x1412, device 0x1724) PCI slot 2


PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4


PCI Adapter ID (vendor 0x1045, device 0xc861) PCI slot 5


HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)


IP35prom in Module 001c01/Slot n0: Revision 6.210


USB controller: type OHCI

/usr/gfx/gfxinfo -vv

Code: Select all


###Graphics board 0 is "ODYSSEY" graphics.


###        Managed (":0.0") 1920x1200


###        BUZZ version B.2


###        PB&J version 1


###        32MB memory


###                Banks: 2, CAS latency: 3


###         Monitor 0 type: SGX 4352


###        Input Sync: Voltage - Video Level; Source - Internal; Genlocked - False


###        Channel 0:


###         Origin = (0,0)


###         Video Output: 1920 pixels, 1200 lines, 60.02Hz (1920x1200_60)


###         Video Format Flags:  (none)


###         Sync Disabled


###         Using Gamma Map 0


###         Monitor Type:  SGI-4352


###         Gain (all color components) - 0.000000 ; range [1,10]


Graphics board 0 is "ODYSSEY" graphics.


Managed (":0.0") 1920x1200


BUZZ version B.1


PB&J version 1


128MB memory


Banks: 4, CAS latency: 3


Compositor port 1 attached to channel 0 nic 0x1004a768


CMP:  No NIC serial number available.


Monitor 0 type: DEL -4075


Input Sync: Voltage - Video Level; Source - Internal; Genlocked - False


Channel 0:


Origin = (0,0)


Video Output: 1920 pixels, 1200 lines, 60.00Hz (1920x1200_60p)


Video Format Flags:  (none)


Sync Disabled


Using Gamma Map 0


Monitor Type:  DEL-61461


Gain (all color components) - 0.000000 ; range [1,10][/i]

uname -aR

Code: Select all


IRIX64 fuel 6.5 6.5.30m 07202013 IP35

scsicontrol -i /dev/scsi/*

Code: Select all


/dev/scsi/sc0d1l0:  Disk          ModusLnkMXO3367SC800600SM108


ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing


Device is  ready


/dev/scsi/sc0d2l0:  Disk          SGI     HUS103014FL3600 SF00


ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing


Device is  ready


/dev/scsi/sc1d4l0:  CD-ROM        TOSHIBA DVD-ROM SD-M14011F09


ANSI vers 2, ISO ver: 0, ECMA ver: 0; supports:  synch linkedcmds


Device is  not ready

/sbin/diskpatch -v

Code: Select all


sc0d1l0:  Disk         ModusLnkMXO3367SC800600SM108  Serial: ML000024


sc0d2l0:  Disk         SGI     HUS103014FL3600 SF00  Serial: V5VBZUGA

Finally, thanks to ratfink and its hinv output , some l1 commands I couldn't have guessed by myself ;-)

l1cmd serial all

Code: Select all


Data                            Location      Value


------------------------------  ------------  --------


Local System Serial Number      EEPROM        08:00:69:10:7C:A7


Local Brick Serial Number       EEPROM        NCJ712


Reference Brick Serial Number   NVRAM         NCJ712






EEPROM      Product Name    Serial         Part Number           Rev  T/W


----------  --------------  -------------  --------------------  ---  ------


NODE        IP34            NCJ712         030_1707_004          C    00


MAC         MAC ADDRESS     NA             NA                    NA   NA


PIMM        IP34PIMM        NNN514         030_1932_001          B    00


###XIO         ASTODYV10       NSR498         030_1826_003          A    00


XIO         ASTODY          MLD922         030_1726_003          E    00




EEPROM     JEDEC-SPD Info           Part Number        Rev  Speed  SGI


---------- ------------------------ ------------------ ---- ------ --------


DIMM 0     CE000000000000000C989800 M3 46L2820DT2-CA0   2D   10.0  N/A


DIMM 2     no hardware detected


DIMM 1     CE000000000000000C7F9800 M3 46L2820DT2-CA0   2D   10.0  N/A


DIMM 3     no hardware detected

l1cmd flash status

Code: Select all


Flash image B currently booted




Image      Status        Revision    Built


-----   -------------   ----------   -----


A     valid           1.40.4       09/29/2005 13:43:39


B     default         1.40.4       09/29/2005 13:43:39

l1cmd env

Code: Select all


Environmental monitoring is enabled and running.




Description    State       Warning Limits     Fault Limits       Current


-------------- ----------  -----------------  -----------------  -------


12V    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.125


12V IO    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.125


5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.096


3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.320


2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.470


1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.466


5V AUX    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.096


3.3V AUX    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.285


PIMM 12V BIAS    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.125


SRAM    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.496


VCPU    Enabled  10%   1.13/  1.38  20%   1.00/  1.50    1.255


PIMM 1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.495


PIMM 3.3V AUX    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.268


PIMM 5V AUX    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.096


XIO 12V BIAS    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.000


XIO 5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.070


XIO 2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.457


XIO 3.3V AUX    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.285




Description     State       Warning RPM  Current RPM


--------------- ----------  -----------  -----------


FAN  0  EXHAUST    Enabled          920         1188


FAN  1       HD    Enabled         1560         2122


FAN  2      PCI    Enabled         1120         1534


FAN  3    XIO 1    Enabled         1600         2721


FAN  4    XIO 2    Enabled         1600         2596


FAN  5       PS    Enabled         1349         3276




Advisory   Critical   Fault      Current


Description       State       Temp       Temp       Temp       Temp


----------------- ----------  ---------  ---------  ---------  ---------


0 NODE 0            Enabled    [Autofan Control]    80C/176F   40C/104F


1 NODE 1            Enabled    [Autofan Control]    80C/176F   41C/105F


2 NODE 2            Enabled    [Autofan Control]    80C/176F   32C/ 89F


3 PIMM              Enabled    [Autofan Control]    80C/176F   47C/116F


4 ODYSSEY           Enabled    [Autofan Control]    80C/176F   45C/113F


5 BEDROCK           Enabled    [Autofan Control]    85C/185F   44C/111F

Hope you like it.

BetXen

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of Fuel: R16k 800, 2Gb, V10, M-Audio, 36+147GB HD at May 4, 2011, 3:39 a.m...

It is a Fujitsu Worldisk, 36GB. I'll have a look at it this evening and give you more details soon. Maybe Ian will read this post and could answer better and faster than me.

If someone wonders what monitor I have, here is tha answer: GDM-FW9011. Sgi 24" 16:10 CRT weighting more than 50kg. My back still remembers (I used to live on the 5th floor without elevator).

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of Fuel: R16k 800, 2Gb, V10, M-Audio, 36+147GB HD at May 4, 2011, 2:19 p.m...

So... the hard disk label says:

Code: Select all


Capacity          36.7GB


RPM               15000


Interface         SCSI 80 PIN


MODEL             MX03367SC800600S

You were right !

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of Happy Star Wars Day!!... 8-) at May 4, 2011, 2:20 p.m...

lol

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of Fuel: R16k 800, 2Gb, V10, M-Audio, 36+147GB HD at May 5, 2011, 9:41 a.m...

I'll try to take some this evening... stay tuned !

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of Fuel: R16k 800, 2Gb, V10, M-Audio, 36+147GB HD at May 8, 2011, 2:57 p.m...

As promised, here are some pics of my new toy and its friends... made in a hurry as I will leave for a business trip tomorrow morning. I'll take better pictures later.

: One corner of my actual computer room

: My new fuel in good company

: All the sgi now in my hands

See you.

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of Fuel: R16k 800, 2Gb, V10, M-Audio, 36+147GB HD at May 10, 2011, 9:20 a.m...

"Nice lair" you said... yes, because I've juste made order before the photo. Normally it's significantly more messy

Regarding the O200, the skins WERE perfect when they were given to me, as the O200 was used in my university and never moved since their installation. Unfortunately I didn't know the plastics were so fragile and tilted one of the towers during a move. Two feet immediately broke, so I had to remove the two others. Finaly, one door "axis" broke too, but on the other module... grrrr !

Anyway, If you know how to make them reproduce, give me a call ! It would be funny to have a baby O200 as paperweight...

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of Fuel: R16k 800, 2Gb, V10, M-Audio, 36+147GB HD at May 11, 2011, 12:55 a.m...

Good idea. I'll try that. They are already broken, so I can't do worse...

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of Fuel: R16k 800, 2Gb, V10, M-Audio, 36+147GB HD at May 11, 2011, 11:58 p.m...

I just read you old topic PS. At work, we'll probably buy a Faro 3D digitizer in a near future. If my collegues from the metrology let me use it, I could maybe give you the dimensions of a o200 skins, even a 3d model if I found enough time to process the data.

We'll see in a few weeks or months.

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
Who joined Sept. 21, 2004, 11:05 a.m.
and authored 229 notes

Wrote on the subject of quick update at May 20, 2011, 4:13 a.m...

Hi.

Nice to hear from you again. Hope everything will turn fine soon.

I don't know if there are open positions, but the Swiss Federal Institute of Technology (EPFL) has different departments where your skill would probably be appreciated. I think in particular about the CRPP (Plasma Physics Research Center, lot of code to be written and data to be analysed) and the IGM (Institute of Mechanical Engineering, fluids mechanics, and so on). I've just seen a position for a tenured full or associate professor in the area of Aerospace Engineering . Maybe it's for you. Anyway, they will probably need research assistant for this new group.

There are several HP Computer in the school. For example Pleiades in the Mechanical Engineering Institute. More informations about other facilities here .

Hope this can help you.

BetXen

P.S.: BTW, the region is wonderful here. EPFL is 500m from the Geneva Lake, mountains are very close,...

_________________
:Onyx2:

4xR12k 400, 8Gb, IR2E, 2x18+3x73GB HD
:A3504L:

16xItanium2 1.6, L2 9MB
:Fuel:

R16k 800 V12, 2Gb, M-Audio, 36+147GB HD, 3Dconnexion SpaceMouse Classic
:Octane2:

Dual R14k 600 V6, 2Go, HD (173Go, 34Go)
:Octane:

R10k 400 MXE, 1280Mo / 2xR10k 300 SSE,...
:O2:

R10k 195, 512Mo / R5k 180, 512Mo / R5k 180->200 motherboard and PM only
:Indigo2IMP:

R10k 195, HighImpact, 160Mo/ R4400 125, Extreme, 160Mo
:O200:

twin O200, 4xR12k 270, 2Go, HD (4x18Go)
:4D70G:

4D70GT... my very first one (now property of musée bolo and the foundation mémoires informatiques )

BetXen
Who joined Sept. 21, 2004, 11:05 a.m.
and authored 229 notes

Wrote on the subject of quick update at July 4, 2011, 11:27 a.m...

Hi

Nice to hear good news from you. I hope you'll have the opportunity to do what you like to.

Cheers,

BetXen

_________________
:Onyx2:

4xR12k 400, 8Gb, IR2E, 2x18+3x73GB HD
:A3504L:

16xItanium2 1.6, L2 9MB
:Fuel:

R16k 800 V12, 2Gb, M-Audio, 36+147GB HD, 3Dconnexion SpaceMouse Classic
:Octane2:

Dual R14k 600 V6, 2Go, HD (173Go, 34Go)
:Octane:

R10k 400 MXE, 1280Mo / 2xR10k 300 SSE,...
:O2:

R10k 195, 512Mo / R5k 180, 512Mo / R5k 180->200 motherboard and PM only
:Indigo2IMP:

R10k 195, HighImpact, 160Mo/ R4400 125, Extreme, 160Mo
:O200:

twin O200, 4xR12k 270, 2Go, HD (4x18Go)
:4D70G:

4D70GT... my very first one (now property of musée bolo and the foundation mémoires informatiques )

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of Onyx2 IR2E: 4xR12k 400, 8Gb, IR2E, 2x18+3x73GB HD at Aug. 31, 2011, 12:50 a.m...

Hi folks !

Thanks to maxsleg, I'm now the happy owner of IMO one of the most desirable sgi... an Onyx2 IR2E. I finally decided to do the trip to his place to pick it up. 8 hours, 80kg and 800km later (+ a lot of spare parts and other gifts), I still think that it was a good idea. It was a long trip but was worth it. Thanks Paul !

So, here are the outputs.

hinv -mv

Code: Select all


Location: /hw/module/1/slot/n2/node


IP31PIMMR12KS Board: barcode JZP950     part 030-1423-002 rev  G


IP31 Board: barcode JZP205     part 030-1523-001 rev  C


Location: /hw/module/1/slot/n1/node


MODULEID Board: barcode K0028621   part              rev


IP31PIMMR12KS Board: barcode KRH836     part 030-1423-002 rev  G


IP31 Board: barcode HGL038     part 030-1523-001 rev  C


4P1G5_MPLN Board: barcode KBW082     part 030-1066-002 rev  L


Location: /hw/module/1/slot/io4/kona


GE16-4 Board: barcode HRD841     part 030-1398-001 rev  B


Location: /hw/module/1/slot/io6/hippi_serial


HIPPI_SERIAL Board: barcode GXD219     part 030-0968-005 rev  A


Location: /hw/module/1/slot/io1/baseio


MIO Board: barcode KDK585     part 030-0880-003 rev  G


BASEIO Board: barcode KDK661     part 030-0734-002 rev  N


Location: /hw/module/1/slot/io5/fibre_channel


FIBRE_CHANNEL Board: barcode GTT357     part 030-0927-003 rev  C


4 400 MHZ IP27 Processors


CPU: MIPS R12000 Processor Chip Revision: 3.5


FPU: MIPS R12010 Floating Point Chip Revision: 3.5


CPU 0 at Module 1/Slot 2/Slice A: 400 Mhz MIPS R12000 Processor Chip (enabled)


Processor revision: 3.5. Scache: Size 8 MB Speed 266 Mhz  Tap 0xa


CPU 1 at Module 1/Slot 2/Slice B: 400 Mhz MIPS R12000 Processor Chip (enabled)


Processor revision: 3.5. Scache: Size 8 MB Speed 266 Mhz  Tap 0xa


CPU 2 at Module 1/Slot 1/Slice A: 400 Mhz MIPS R12000 Processor Chip (enabled)


Processor revision: 3.5. Scache: Size 8 MB Speed 266 Mhz  Tap 0xa


CPU 3 at Module 1/Slot 1/Slice B: 400 Mhz MIPS R12000 Processor Chip (enabled)


Processor revision: 3.5. Scache: Size 8 MB Speed 266 Mhz  Tap 0xa


Main memory size: 8192 Mbytes


Instruction cache size: 32 Kbytes


Data cache size: 32 Kbytes


Secondary unified instruction/data cache size: 8 Mbytes


Memory at Module 1/Slot 82: 4096 MB (enabled)


Bank 0 contains 512 MB (Premium) DIMMS (enabled)


Bank 1 contains 512 MB (Premium) DIMMS (enabled)


Bank 2 contains 512 MB (Premium) DIMMS (enabled)


Bank 3 contains 512 MB (Premium) DIMMS (enabled)


Bank 4 contains 512 MB (Premium) DIMMS (enabled)


Bank 5 contains 512 MB (Premium) DIMMS (enabled)


Bank 6 contains 512 MB (Premium) DIMMS (enabled)


Bank 7 contains 512 MB (Premium) DIMMS (enabled)


Memory at Module 1/Slot 81: 4096 MB (enabled)


Bank 0 contains 512 MB (Standard) DIMMS (enabled)


Bank 1 contains 512 MB (Standard) DIMMS (enabled)


Bank 2 contains 512 MB (Standard) DIMMS (enabled)


Bank 3 contains 512 MB (Standard) DIMMS (enabled)


Bank 4 contains 512 MB (Standard) DIMMS (enabled)


Bank 5 contains 512 MB (Standard) DIMMS (enabled)


Bank 6 contains 512 MB (Standard) DIMMS (enabled)


Bank 7 contains 512 MB (Standard) DIMMS (enabled)


Integral SCSI controller 2: Version Fibre Channel AIC-1160, revision 2


Integral SCSI controller 0: Version QL1040B (rev. 2), single ended


Disk drive: unit 1 on SCSI controller 0 (unit 1)


Disk drive: unit 2 on SCSI controller 0 (unit 2)


Disk drive: unit 3 on SCSI controller 0 (unit 3)


Disk drive: unit 4 on SCSI controller 0 (unit 4)


Disk drive: unit 5 on SCSI controller 0 (unit 5)


CDROM: unit 6 on SCSI controller 0


Integral SCSI controller 1: Version QL1040B (rev. 2), single ended


Integral SCSI controller 3: Version Fibre Channel AIC-1160, revision 2


IOC3/IOC4 serial port: tty1


IOC3/IOC4 serial port: tty2


IOC3/IOC4 serial port: tty3


IOC3/IOC4 serial port: tty4


IOC3 parallel port: plp1


Graphics board: InfiniteReality2E


Integral Fast Ethernet: ef0, version 1, module 1, slot io1, pci 2


Iris Audio Processor: version RAD revision 7.0, number 1


Origin BASEIO board, module 1 slot 1: Revision 4


PCI Adapter ID (vendor 0x10a9, device 0x0002) PCI slot 0


PCI Adapter ID (vendor 0x10a9, device 0x0002) PCI slot 1


Origin FIBRE CHANNEL board, module 1 slot 5: Revision 3


PCI Adapter ID (vendor 0x9004, device 0x1160) PCI slot 0


PCI Adapter ID (vendor 0x9004, device 0x1160) PCI slot 1


PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 6


PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2


PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0


PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1


PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 7


IOC3/IOC4 external interrupts: 1


HUB in Module 1/Slot 2: Revision 6 Speed 100.00 Mhz (enabled)


HUB in Module 1/Slot 1: Revision 6 Speed 100.00 Mhz (enabled)


IP27prom in Module 1/Slot n2: Revision 6.156


IP27prom in Module 1/Slot n1: Revision 6.156


IO6prom on Global Master Baseio in Module 1/Slot io2: Revision 6.156

/usr/gfx/gfxinfo -vv

Code: Select all


Graphics board 0 is "KONAL" graphics.


Managed (":0.0") 1280x1024


Display has 2 channels


4 GEs (of 4), occmask = 0x0f


4MB external BEF ram, 32bit path


2 RM9 boards (of 2) 1/1/0/0


Texture Memory: 64MB/64MB/-/-


Large pixel depth


32K cmap


brd: 80f61806 3020c06/3020c06/-/- f9391002


ge: 0 14832057 24731057 14231057


rm0: 15032057 15431057


4631057 2/2/2/2


4d31057 2/2/2/2/2/2/2/2


4938057 5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5


rm1: 15032057 15431057


4631057 2/2/2/2


4d31057 2/2/2/2/2/2/2/2


4938057 5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5


dg: 05532057


5838057 1/1/1/1


5631057 1/1


GE:   NIC #:      0000.0031.ca5a (family: 0b)


Serial #:   HRD841


Part #:     030-1398-001


rev_code:   B


grp_code:   0xff


capability: "\ff\ff\ff\ff"


variety:    0xff


name:       GE16-4


KT:   No NIC serial number available.


RM0:  NIC #:      0000.003c.1ecc (family: 0b)


Serial #:   JLS202


Part #:     030-1402-001


rev_code:   B


grp_code:   0xff


capability: "\ff\ff\ff\ff"


variety:    0xff


name:       RM9


TM0:  NIC #:      0000.003c.06a8 (family: 0b)


Serial #:   JLT642


Part #:     030-1053-001


rev_code:   H


grp_code:   0xff


capability: "\ff\ff\ff\ff"


variety:    0xff


name:       TM7-64


RM1:  NIC #:      0000.003c.1eec (family: 0b)


Serial #:   JLS197


Part #:     030-1402-001


rev_code:   B


grp_code:   0xff


capability: "\ff\ff\ff\ff"


variety:    0xff


name:       RM9


TM1:  NIC #:      0000.003c.3707 (family: 0b)


Serial #:   JLM310


Part #:     030-1053-001


rev_code:   H


grp_code:   0xff


capability: "\ff\ff\ff\ff"


variety:    0xff


name:       TM7-64


RM2:  No NIC serial number available.


TM2:  No NIC serial number available.


RM3:  No NIC serial number available.


TM3:  No NIC serial number available.


BP:   No NIC serial number available.


DG:   NIC #:      0000.0014.8d6a (family: 0b)


Serial #:   HKT003


Part #:     030-1055-001


rev_code:   P


grp_code:   0xff


capability: "\ff\ff\ff\ff"


variety:    0xff


name:       DG5-2


DGOPT:No NIC serial number available.


Input Sync: Voltage - Video Level; Source - Internal; Genlocked -


False


Channel 0:


Origin = (0,0)


Video Output: 1280 pixels, 1024 lines, 72.00Hz (1280x1024_72.vfo)


Video Format Flags:  (none)


Sync Output(s):


Composite sync on Green


Composite TTL sync on Aux 0


Using Gamma Map 0


Monitor Type:  Unknown


Pedestal Enabled


Channel not blanked


Gain (all color components) - 1.000000 (nominal)


Horizontal Phase - 0.00 pixels; range [0.00,1680.00]


Vertical Phase - 0 lines; range [-2,2]

uname -aR

Code: Select all


IRIX64 onyx2 6.5 6.5.30f 07202013 IP27

Very original hostname, isn't it ?

scsicontrol -i /dev/scsi/*

Code: Select all


/dev/scsi/sc0d1l0:  Disk          SGI     IBM  DGHS18Y    0190


ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds


cmdqueing


Device is  ready


/dev/scsi/sc0d2l0:  Disk          IBM     IC35L073UCDY10-0S27N


ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds


cmdqueing


Device is  ready


/dev/scsi/sc0d3l0:  Disk          IBM     IC35L073UCDY10-0S27N


ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds


cmdqueing


Device is  ready


/dev/scsi/sc0d4l0:  Disk          ModusLnk


ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds


cmdqueing


Device is  ready


/dev/scsi/sc0d5l0:  Disk          SGI     IBM  DGHS18Y    0190


ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds


cmdqueing


Device is  ready


/dev/scsi/sc0d6l0:  CD-ROM        TOSHIBA CD-ROM XM-6201TA1037


ANSI vers 2, ISO ver: 0, ECMA ver: 0; supports:  reladdr synch linkedcmds


Device is  not ready

/sbin/diskpatch -v

Code: Select all


sc0d1l0:  Disk         SGI     IBM  DGHS18Y    0190  Serial: 681641CC


sc0d2l0:  Disk         IBM     IC35L073UCDY10-0S27N  Serial: E6VRUE2D


sc0d3l0:  Disk         IBM     IC35L073UCDY10-0S27N  Serial: E6VRT6WD


sc0d4l0:  Disk         ModusLnk                      Serial: UF03P220


sc0d5l0:  Disk         SGI     IBM  DGHS18Y    0190  Serial: 680EA510

boot sequence

Code: Select all


IP27 PROM SGI Version 6.156  built 11:27:56 AM Nov 18, 2003


Testing/Initializing memory ...............             DONE


Copying PROM code to memory ...............             DONE


Discovering local IO ......................


Found an io Board with nic 030-0968-005.


DONE


Discovering NUMAlink connectivity .........             DONE


Found 2 objects (2 hubs, 0 routers) in 10465 usec


Waiting for peers to complete discovery....             DONE


Global master is /hw/module/1/slot/n2


Testing/Initializing all memory ...........         DONE


Checking partitioning information .........              DONE


Loading BASEIO prom .......................              DONE




BASEIO PROM Monitor SGI Version 6.156  built 11:26:28 AM Nov 18, 2003 (BE64)


4 CPUs on 2 nodes found.


Installing PROM Device drivers ............


Base I/O Ethernet set to /dev/ethernet/ef0


Installing Graphics Console...


graphics install: searching for pipe 0




Walking SCSI Adapter 0 (/hw/module/1/slot/io1), (pci id 0)


1+ 2+ 3+ 4+ 5+ 6+ 7- 8- 9- 10- 11- 12- 13- 14- 15- = 6 device(s)






Walking SCSI Adapter 1 (/hw/module/1/slot/io1), (pci id 1)


1- 2- 3- 4- 5- 6- 7- 8- 9- 10- 11- 12- 13- 14- 15- = 0 device(s)




Initializing PROM Device drivers ..........             DONE


WARNING: (SYS-DEGRADED):Mixture of premium & std dimms


Standard dimms on nasids : 1


/hw/module/1/slot/n1/node


Premium dimms on nasids : 0


/hw/module/1/slot/n2/node

Hope you like it. I do...

BetXen

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of Onyx2 IR2E: 4xR12k 400, 8Gb, IR2E, 2x18+3x73GB HD at Aug. 31, 2011, 2:34 a.m...

Hi JJ,

Yes, I've seen that, but didn't remove the boards up to now. I will search for an imbus key and have a look at it asap.
I will open a new thread about nice 3D softwares suggestions pretty soon. As you have some Onyx2, I hope you will give me some hints.

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of Onyx2 IR2E: 4xR12k 400, 8Gb, IR2E, 2x18+3x73GB HD at Sept. 8, 2011, 12:27 a.m...

I have finally received a 7/64" key and removed the directory memory. No more "SYS-DEGRADED" warning, of course.

Please tell me where the error is... : The key (15cm long with a rubber T handle) came from the UK for 8 Swiss francs shipping included. The cheapest I've found on a swiss online shop was 25CHF + shipping (for a small L-shaped one). Ahhh, globalization !

I've also installed all the Onyx2 demos and am looking at them. What do you suggest me to install to unleash the IR2E and get some fun ? 3D demos, games, softs ? I would also like to display some FEA results. Which soft do you think is the best for that ? Paraview or sth like that ? Maybe you also know a good DICOM viewer ?

Thanks in advance.

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of 1920x1080_60Hz with Onyx2 at Sept. 29, 2011, 7:29 a.m...

Hi !

Due to the birth of our child, I had to move the Onyx2 out of his room to the living room. Fortunately, my TV syncs on green (it is a LG 42LH3010). Thus I opened ircombine and tried different resolutions. No problem to display 1680x1050_60Hz, but I can't successfully display 1920x1080_60. My desktop appears on the lower right part of the screen, with two large black bands on the left and top regions of the TV (around 15cm on the left and 5 on top). Moreover, I can't see the whole managed area (for instance iconbar is only half visible) and it is slightly squeezed horizontally.

I'm not familiar with ircombine and this type of hardware, so I may have misunderstood something. Do you have any ideas that would help me resolve this problem ? It would be nice to use the whole surface at the highest resolution

Thanks in advance.

BetXen

P.S.: If needed I can include pictures, but I'm at work now.

: oxygen (4xR12k400) / :A3504L:

: neon (16xI2 1.6, 9MB L2) / :O200:

: beryllium (4xR12k270)
:Fuel:

: nitrogen (R16k800) / :Octane2:

: carbon (2xR14k600) / :Octane:

: lithium (R10k400) / :Octane:

: fluorine (2xR12k300) / spare 2xR12k360
:O2:

: hydrogen (R10k195) / :O2:

: sodium (R5k180) / :O2:

: R5k180->200 MB and PM only
:Indigo2IMP:

: helium (R10k195, HighImpact) / :Indigo2IMP:

: boron (R4k250)/ :Indigo:

: magnesium (R4k100) / :Indy:

: aluminium (R5k180)
:4D70GT:

4D70GT : my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of 1920x1080_60Hz with Onyx2 at Sept. 30, 2011, 7:33 a.m...

Thanks a lot recondas. I will have a look at your links during the week-end. Unfortunately, I will be in the chalet and have to try later on next week.

In the meantime, I've found this table in the manual of my TV:

: LGLCD TV 42LH3010 Supported Display Resolutions; display resolutions (LG42LH3010 RGB PC).JPG (54.62 KiB) Viewed 1680 times

Have a good week-end.

BetXen

: oxygen (4xR12k400) / :A3504L:

: neon (16xI2 1.6, 9MB L2) / :O200:

: beryllium (4xR12k270)
:Fuel:

: nitrogen (R16k800) / :Octane2:

: carbon (2xR14k600) / :Octane:

: lithium (R10k400) / :Octane:

: fluorine (2xR12k300) / spare 2xR12k360
:O2:

: hydrogen (R10k195) / :O2:

: sodium (R5k180) / :O2:

: R5k180->200 MB and PM only
:Indigo2IMP:

: helium (R10k195, HighImpact) / :Indigo2IMP:

: boron (R4k250)/ :Indigo:

: magnesium (R4k100) / :Indy:

: aluminium (R5k180)
:4D70GT:

4D70GT : my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of 1920x1080_60Hz with Onyx2 at Oct. 10, 2011, 12:24 a.m...

Recondas,

Thanks for your work. I didn't have a lot of time last week, but tried anyway to grab the EDID infos. I google a bit and downloaded some applications. No success yet. They always tell me that the wil get the EDID from Windows registry. I thought ther would be a way to ask the monitor directly... Yesterday I also upgraded my TV with the latest firmware and will try to get the EDID again today. It seem I will have too google a bit more, as you say there are simple methods to do it.

In the meantime, I also connected my laptop. No problem with HDMI but when I connect it via DB15, It displays the same way the Onyx2 does: two black bands... strange. Didn't check with the noew firmware for the moment.

I will also try your file this evening. Thanks a lot.

BetXen

: oxygen (4xR12k400) / :A3504L:

: neon (16xI2 1.6, 9MB L2) / :O200:

: beryllium (4xR12k270)
:Fuel:

: nitrogen (R16k800) / :Octane2:

: carbon (2xR14k600) / :Octane:

: lithium (R10k400) / :Octane:

: fluorine (2xR12k300) / spare 2xR12k360
:O2:

: hydrogen (R10k195) / :O2:

: sodium (R5k180) / :O2:

: R5k180->200 MB and PM only
:Indigo2IMP:

: helium (R10k195, HighImpact) / :Indigo2IMP:

: boron (R4k250)/ :Indigo:

: magnesium (R4k100) / :Indy:

: aluminium (R5k180)
:4D70GT:

4D70GT : my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of When were you and your spouse last in tandem? at Oct. 10, 2011, 1:01 a.m...

Oskar45 wrote: I would be willing to post one or two other pics though, provided there is any interest in them at all...

There is... I like wildlife photography too, even if I don't have enough time to do it properly by myself. My fauna takes me too much time and is too young for the moment to come with me up the mountains before sunrise.

I look forward to seeing more of your pics.

BetXen

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote on the subject of 1920x1080_60Hz with Onyx2 at Oct. 11, 2011, 9:37 a.m...

Recondas... you're a genius

It works flawlessly ! My desktop completely fills the TV and the details are sharp. When I booted it up, even with the new TV firmware, the result was identical. Then I loaded you vfo file in ircombine an... wow... how impressive it is on a 42" display. I need to find good looking demos to show my friends...

Anyway, I will continue trying to get the EDID from my Windows notebook. It's strange that it cannot display correctly.

Thanks so much. Best regards.

: oxygen (4xR12k400) / :A3504L:

: neon (16xI2 1.6, 9MB L2) / :O200:

: beryllium (4xR12k270)
:Fuel:

: nitrogen (R16k800) / :Octane2:

: carbon (2xR14k600) / :Octane:

: lithium (R10k400) / :Octane:

: fluorine (2xR12k300) / spare 2xR12k360
:O2:

: hydrogen (R10k195) / :O2:

: sodium (R5k180) / :O2:

: R5k180->200 MB and PM only
:Indigo2IMP:

: helium (R10k195, HighImpact) / :Indigo2IMP:

: boron (R4k250)/ :Indigo:

: magnesium (R4k100) / :Indy:

: aluminium (R5k180)
:4D70GT:

4D70GT : my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .