SGI: hinv

Onyx2 IR2E: 4xR12k 400, 8Gb, IR2E, 2x18+3x73GB HD

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote the following at Aug. 31, 2011, 12:50 a.m...

Hi folks !

Thanks to maxsleg, I'm now the happy owner of IMO one of the most desirable sgi... an Onyx2 IR2E. I finally decided to do the trip to his place to pick it up. 8 hours, 80kg and 800km later (+ a lot of spare parts and other gifts), I still think that it was a good idea. It was a long trip but was worth it. Thanks Paul !

So, here are the outputs.

hinv -mv

Code: Select all


   Location: /hw/module/1/slot/n2/node
   

   IP31PIMMR12KS Board: barcode JZP950     part 030-1423-002 rev  G
   

   IP31 Board: barcode JZP205     part 030-1523-001 rev  C
   

   Location: /hw/module/1/slot/n1/node
   

   MODULEID Board: barcode K0028621   part              rev
   

   IP31PIMMR12KS Board: barcode KRH836     part 030-1423-002 rev  G
   

   IP31 Board: barcode HGL038     part 030-1523-001 rev  C
   

   4P1G5_MPLN Board: barcode KBW082     part 030-1066-002 rev  L
   

   Location: /hw/module/1/slot/io4/kona
   

   GE16-4 Board: barcode HRD841     part 030-1398-001 rev  B
   

   Location: /hw/module/1/slot/io6/hippi_serial
   

   HIPPI_SERIAL Board: barcode GXD219     part 030-0968-005 rev  A
   

   Location: /hw/module/1/slot/io1/baseio
   

   MIO Board: barcode KDK585     part 030-0880-003 rev  G
   

   BASEIO Board: barcode KDK661     part 030-0734-002 rev  N
   

   Location: /hw/module/1/slot/io5/fibre_channel
   

   FIBRE_CHANNEL Board: barcode GTT357     part 030-0927-003 rev  C
   

   4 400 MHZ IP27 Processors
   

   CPU: MIPS R12000 Processor Chip Revision: 3.5
   

   FPU: MIPS R12010 Floating Point Chip Revision: 3.5
   

   CPU 0 at Module 1/Slot 2/Slice A: 400 Mhz MIPS R12000 Processor Chip (enabled)
   

   Processor revision: 3.5. Scache: Size 8 MB Speed 266 Mhz  Tap 0xa
   

   CPU 1 at Module 1/Slot 2/Slice B: 400 Mhz MIPS R12000 Processor Chip (enabled)
   

   Processor revision: 3.5. Scache: Size 8 MB Speed 266 Mhz  Tap 0xa
   

   CPU 2 at Module 1/Slot 1/Slice A: 400 Mhz MIPS R12000 Processor Chip (enabled)
   

   Processor revision: 3.5. Scache: Size 8 MB Speed 266 Mhz  Tap 0xa
   

   CPU 3 at Module 1/Slot 1/Slice B: 400 Mhz MIPS R12000 Processor Chip (enabled)
   

   Processor revision: 3.5. Scache: Size 8 MB Speed 266 Mhz  Tap 0xa
   

   Main memory size: 8192 Mbytes
   

   Instruction cache size: 32 Kbytes
   

   Data cache size: 32 Kbytes
   

   Secondary unified instruction/data cache size: 8 Mbytes
   

   Memory at Module 1/Slot 82: 4096 MB (enabled)
   

   Bank 0 contains 512 MB (Premium) DIMMS (enabled)
   

   Bank 1 contains 512 MB (Premium) DIMMS (enabled)
   

   Bank 2 contains 512 MB (Premium) DIMMS (enabled)
   

   Bank 3 contains 512 MB (Premium) DIMMS (enabled)
   

   Bank 4 contains 512 MB (Premium) DIMMS (enabled)
   

   Bank 5 contains 512 MB (Premium) DIMMS (enabled)
   

   Bank 6 contains 512 MB (Premium) DIMMS (enabled)
   

   Bank 7 contains 512 MB (Premium) DIMMS (enabled)
   

   Memory at Module 1/Slot 81: 4096 MB (enabled)
   

   Bank 0 contains 512 MB (Standard) DIMMS (enabled)
   

   Bank 1 contains 512 MB (Standard) DIMMS (enabled)
   

   Bank 2 contains 512 MB (Standard) DIMMS (enabled)
   

   Bank 3 contains 512 MB (Standard) DIMMS (enabled)
   

   Bank 4 contains 512 MB (Standard) DIMMS (enabled)
   

   Bank 5 contains 512 MB (Standard) DIMMS (enabled)
   

   Bank 6 contains 512 MB (Standard) DIMMS (enabled)
   

   Bank 7 contains 512 MB (Standard) DIMMS (enabled)
   

   Integral SCSI controller 2: Version Fibre Channel AIC-1160, revision 2
   

   Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
   

   Disk drive: unit 1 on SCSI controller 0 (unit 1)
   

   Disk drive: unit 2 on SCSI controller 0 (unit 2)
   

   Disk drive: unit 3 on SCSI controller 0 (unit 3)
   

   Disk drive: unit 4 on SCSI controller 0 (unit 4)
   

   Disk drive: unit 5 on SCSI controller 0 (unit 5)
   

   CDROM: unit 6 on SCSI controller 0
   

   Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
   

   Integral SCSI controller 3: Version Fibre Channel AIC-1160, revision 2
   

   IOC3/IOC4 serial port: tty1
   

   IOC3/IOC4 serial port: tty2
   

   IOC3/IOC4 serial port: tty3
   

   IOC3/IOC4 serial port: tty4
   

   IOC3 parallel port: plp1
   

   Graphics board: InfiniteReality2E
   

   Integral Fast Ethernet: ef0, version 1, module 1, slot io1, pci 2
   

   Iris Audio Processor: version RAD revision 7.0, number 1
   

   Origin BASEIO board, module 1 slot 1: Revision 4
   

   PCI Adapter ID (vendor 0x10a9, device 0x0002) PCI slot 0
   

   PCI Adapter ID (vendor 0x10a9, device 0x0002) PCI slot 1
   

   Origin FIBRE CHANNEL board, module 1 slot 5: Revision 3
   

   PCI Adapter ID (vendor 0x9004, device 0x1160) PCI slot 0
   

   PCI Adapter ID (vendor 0x9004, device 0x1160) PCI slot 1
   

   PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 6
   

   PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
   

   PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
   

   PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
   

   PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 7
   

   IOC3/IOC4 external interrupts: 1
   

   HUB in Module 1/Slot 2: Revision 6 Speed 100.00 Mhz (enabled)
   

   HUB in Module 1/Slot 1: Revision 6 Speed 100.00 Mhz (enabled)
   

   IP27prom in Module 1/Slot n2: Revision 6.156
   

   IP27prom in Module 1/Slot n1: Revision 6.156
   

   IO6prom on Global Master Baseio in Module 1/Slot io2: Revision 6.156

/usr/gfx/gfxinfo -vv

Code: Select all


   Graphics board 0 is "KONAL" graphics.
   

   Managed (":0.0") 1280x1024
   

   Display has 2 channels
   

   4 GEs (of 4), occmask = 0x0f
   

   4MB external BEF ram, 32bit path
   

   2 RM9 boards (of 2) 1/1/0/0
   

   Texture Memory: 64MB/64MB/-/-
   

   Large pixel depth
   

   32K cmap
   

   brd: 80f61806 3020c06/3020c06/-/- f9391002
   

   ge: 0 14832057 24731057 14231057
   

   rm0: 15032057 15431057
   

   4631057 2/2/2/2
   

   4d31057 2/2/2/2/2/2/2/2
   

   4938057 5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5
   

   rm1: 15032057 15431057
   

   4631057 2/2/2/2
   

   4d31057 2/2/2/2/2/2/2/2
   

   4938057 5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5
   

   dg: 05532057
   

   5838057 1/1/1/1
   

   5631057 1/1
   

   GE:   NIC #:      0000.0031.ca5a (family: 0b)
   

   Serial #:   HRD841
   

   Part #:     030-1398-001
   

   rev_code:   B
   

   grp_code:   0xff
   

   capability: "\ff\ff\ff\ff"
   

   variety:    0xff
   

   name:       GE16-4
   

   KT:   No NIC serial number available.
   

   RM0:  NIC #:      0000.003c.1ecc (family: 0b)
   

   Serial #:   JLS202
   

   Part #:     030-1402-001
   

   rev_code:   B
   

   grp_code:   0xff
   

   capability: "\ff\ff\ff\ff"
   

   variety:    0xff
   

   name:       RM9
   

   TM0:  NIC #:      0000.003c.06a8 (family: 0b)
   

   Serial #:   JLT642
   

   Part #:     030-1053-001
   

   rev_code:   H
   

   grp_code:   0xff
   

   capability: "\ff\ff\ff\ff"
   

   variety:    0xff
   

   name:       TM7-64
   

   RM1:  NIC #:      0000.003c.1eec (family: 0b)
   

   Serial #:   JLS197
   

   Part #:     030-1402-001
   

   rev_code:   B
   

   grp_code:   0xff
   

   capability: "\ff\ff\ff\ff"
   

   variety:    0xff
   

   name:       RM9
   

   TM1:  NIC #:      0000.003c.3707 (family: 0b)
   

   Serial #:   JLM310
   

   Part #:     030-1053-001
   

   rev_code:   H
   

   grp_code:   0xff
   

   capability: "\ff\ff\ff\ff"
   

   variety:    0xff
   

   name:       TM7-64
   

   RM2:  No NIC serial number available.
   

   TM2:  No NIC serial number available.
   

   RM3:  No NIC serial number available.
   

   TM3:  No NIC serial number available.
   

   BP:   No NIC serial number available.
   

   DG:   NIC #:      0000.0014.8d6a (family: 0b)
   

   Serial #:   HKT003
   

   Part #:     030-1055-001
   

   rev_code:   P
   

   grp_code:   0xff
   

   capability: "\ff\ff\ff\ff"
   

   variety:    0xff
   

   name:       DG5-2
   

   DGOPT:No NIC serial number available.
   

   Input Sync: Voltage - Video Level; Source - Internal; Genlocked -
   

   False
   

   Channel 0:
   

   Origin = (0,0)
   

   Video Output: 1280 pixels, 1024 lines, 72.00Hz (1280x1024_72.vfo)
   

   Video Format Flags:  (none)
   

   Sync Output(s):
   

   Composite sync on Green
   

   Composite TTL sync on Aux 0
   

   Using Gamma Map 0
   

   Monitor Type:  Unknown
   

   Pedestal Enabled
   

   Channel not blanked
   

   Gain (all color components) - 1.000000 (nominal)
   

   Horizontal Phase - 0.00 pixels; range [0.00,1680.00]
   

   Vertical Phase - 0 lines; range [-2,2]

uname -aR

Code: Select all


   IRIX64 onyx2 6.5 6.5.30f 07202013 IP27

Very original hostname, isn't it ?

scsicontrol -i /dev/scsi/*

Code: Select all


   /dev/scsi/sc0d1l0:  Disk          SGI     IBM  DGHS18Y    0190
   

   ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds
   

   cmdqueing
   

   Device is  ready
   

   /dev/scsi/sc0d2l0:  Disk          IBM     IC35L073UCDY10-0S27N
   

   ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds
   

   cmdqueing
   

   Device is  ready
   

   /dev/scsi/sc0d3l0:  Disk          IBM     IC35L073UCDY10-0S27N
   

   ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds
   

   cmdqueing
   

   Device is  ready
   

   /dev/scsi/sc0d4l0:  Disk          ModusLnk
   

   ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds
   

   cmdqueing
   

   Device is  ready
   

   /dev/scsi/sc0d5l0:  Disk          SGI     IBM  DGHS18Y    0190
   

   ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds
   

   cmdqueing
   

   Device is  ready
   

   /dev/scsi/sc0d6l0:  CD-ROM        TOSHIBA CD-ROM XM-6201TA1037
   

   ANSI vers 2, ISO ver: 0, ECMA ver: 0; supports:  reladdr synch linkedcmds
   

   Device is  not ready

/sbin/diskpatch -v

Code: Select all


   sc0d1l0:  Disk         SGI     IBM  DGHS18Y    0190  Serial: 681641CC
   

   sc0d2l0:  Disk         IBM     IC35L073UCDY10-0S27N  Serial: E6VRUE2D
   

   sc0d3l0:  Disk         IBM     IC35L073UCDY10-0S27N  Serial: E6VRT6WD
   

   sc0d4l0:  Disk         ModusLnk                      Serial: UF03P220
   

   sc0d5l0:  Disk         SGI     IBM  DGHS18Y    0190  Serial: 680EA510

boot sequence

Code: Select all


   IP27 PROM SGI Version 6.156  built 11:27:56 AM Nov 18, 2003
   

   Testing/Initializing memory ...............             DONE
   

   Copying PROM code to memory ...............             DONE
   

   Discovering local IO ......................
   

   Found an io Board with nic 030-0968-005.
   

   DONE
   

   Discovering NUMAlink connectivity .........             DONE
   

   Found 2 objects (2 hubs, 0 routers) in 10465 usec
   

   Waiting for peers to complete discovery....             DONE
   

   Global master is /hw/module/1/slot/n2
   

   Testing/Initializing all memory ...........         DONE
   

   Checking partitioning information .........              DONE
   

   Loading BASEIO prom .......................              DONE
   

   

   BASEIO PROM Monitor SGI Version 6.156  built 11:26:28 AM Nov 18, 2003 (BE64)
   

   4 CPUs on 2 nodes found.
   

   Installing PROM Device drivers ............
   

   Base I/O Ethernet set to /dev/ethernet/ef0
   

   Installing Graphics Console...
   

   graphics install: searching for pipe 0
   

   

   Walking SCSI Adapter 0 (/hw/module/1/slot/io1), (pci id 0)
   

   1+ 2+ 3+ 4+ 5+ 6+ 7- 8- 9- 10- 11- 12- 13- 14- 15- = 6 device(s)
   

   

   

   Walking SCSI Adapter 1 (/hw/module/1/slot/io1), (pci id 1)
   

   1- 2- 3- 4- 5- 6- 7- 8- 9- 10- 11- 12- 13- 14- 15- = 0 device(s)
   

   

   Initializing PROM Device drivers ..........             DONE
   

   WARNING: (SYS-DEGRADED):Mixture of premium & std dimms
   

   Standard dimms on nasids : 1
   

   /hw/module/1/slot/n1/node
   

   Premium dimms on nasids : 0
   

   /hw/module/1/slot/n2/node

Hope you like it. I do...

BetXen

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

jan-jaap
From Wijchen, The Netherlands
Who joined June 17, 2004, 11:35 a.m.

Wrote the following at Aug. 31, 2011, 2:25 a.m...

BetXen wrote: I'm now the happy owner of IMO one of the most desirable sgi... an Onyx2 IR2E.

Very nice indeed, congratulations!

BetXen wrote: boot sequence

Code: Select all
Initializing PROM Device drivers .......... DONE WARNING: (SYS-DEGRADED):Mixture of premium & std dimms Standard dimms on nasids : 1 /hw/module/1/slot/n1/node Premium dimms on nasids : 0 /hw/module/1/slot/n2/node

Looks like you've got a nodeboard in slot N2 with directory RAM in it, and one without in N1. Directory RAM is rather useless in a deskside Onyx2 since it cannot be (numa)linked into a larger configuration, and directory RAM is only required for large (32+ CPU's ?) configurations

BetXen wrote: Hope you like it. I do...

I'm a sucker for Onyx2's. Crimsons too :mrgreen:

PS: If you're ever looking for 7/64" hex (inbus) keys in Europe and can't find them online, go to a garage that deals with US cars or motorcycles (Harley Davidson etc.). They have them too.

Now this is a deep dark secret, so everybody keep it quiet

It turns out that when reset, the WD33C93 defaults to a SCSI ID of 0, and it was simpler to leave it that way... -- Dave Olson, in comp.sys.sgi
Currently in commercial service:

(2x)

In the museum : almost every MIPS/IRIX system.
Wanted : GM1 board for Professional Series GT graphics (030-0076-003, 030-0076-004)

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote the following at Aug. 31, 2011, 2:34 a.m...

Hi JJ,

Yes, I've seen that, but didn't remove the boards up to now. I will search for an imbus key and have a look at it asap.
I will open a new thread about nice 3D softwares suggestions pretty soon. As you have some Onyx2, I hope you will give me some hints.

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

4130photo
From Bonn / Germany
Who joined Oct. 6, 2005, 12:01 p.m.

Wrote the following at Sept. 2, 2011, 11:03 a.m...

Very nice machine :mrgreen:

I also think that an Onyx2 with IR in any configuration is one of the most desirable computers ever built :mrgreen:

And i also know the trips to get these...

BetXen wrote: Hi folks !

Thanks to maxsleg, I'm now the happy owner of IMO one of the most desirable sgi... an Onyx2 IR2E. I finally decided to do the trip to his place to pick it up. 8 hours, 80kg and 800km later (+ a lot of spare parts and other gifts), I still think that it was a good idea. It was a long trip but was worth it. Thanks Paul !

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote the following at Sept. 8, 2011, 12:27 a.m...

I have finally received a 7/64" key and removed the directory memory. No more "SYS-DEGRADED" warning, of course.

Please tell me where the error is... : The key (15cm long with a rubber T handle) came from the UK for 8 Swiss francs shipping included. The cheapest I've found on a swiss online shop was 25CHF + shipping (for a small L-shaped one). Ahhh, globalization !

I've also installed all the Onyx2 demos and am looking at them. What do you suggest me to install to unleash the IR2E and get some fun ? 3D demos, games, softs ? I would also like to display some FEA results. Which soft do you think is the best for that ? Paraview or sth like that ? Maybe you also know a good DICOM viewer ?

Thanks in advance.

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .