SGI: hinv

Fuel: R16k 800, 2Gb, V10, M-Audio, 36+147GB HD

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote the following at May 3, 2011, 2:35 p.m...

EDITED 12.01.2012: V10 replaced by V12

After so many years I finally decided to buy a fuel. Hopefully Ian, as always, had lots of machines available at a very reasonable price. Moreover, he put so much care in the preparation, personalisation, packing and shipping of it that I'm fully satisfied. If you would like a new box working like a charm, he is definitely the guy you should contact. Thanks again for all, Ian.

I didn't found enough time up to now to discover every personalisation and gift he included... but I will have soon. I'm really looking forward to playing with it. It's such a nice machine.

Let's have a look at its outputs right now !

hinv -mv

Code: Select all


Location: /hw/module/001c01/node


IP34 Board: barcode NCJ712     part 030-1707-004 rev -C


Location: /hw/module/001c01/node/cpubus/0


IP34PIMM Board: barcode NNN514     part 030-1932-001 rev -B


###Location: /hw/module/001c01/Ibrick/xtalk/13


###       ASTODYV10 Board: barcode NSR498     part 030-1826-003 rev -A


Location: /hw/module/001c01/Ibrick/xtalk/13


ASTODY Board: barcode MLD922     part 030-1726-003 rev -E


Location: /hw/module/001c01/Ibrick/xtalk/14


IP34 Board: barcode NCJ712     part 030-1707-004 rev -C


Location: /hw/module/001c01/Ibrick/xtalk/15


IP34 Board: barcode NCJ712     part 030-1707-004 rev -C


1 800 MHZ IP35 Processor


CPU: MIPS R16000 Processor Chip Revision: 2.2


FPU: MIPS R16010 Floating Point Chip Revision: 2.2


CPU 0 at Module 001c01/Slot 0/Slice A: 800 Mhz MIPS R16000 Processor Chip (enabled)


Processor revision: 2.2. Scache: Size 4 MB Speed 400 Mhz  Tap 0xa


Main memory size: 2048 Mbytes


Instruction cache size: 32 Kbytes


Data cache size: 32 Kbytes


Secondary unified instruction/data cache size: 4 Mbytes


Memory at Module 001c01/Slot 0: 2048 MB (enabled)


Bank 0 contains 1024 MB (Premium) DIMMS (enabled)


Bank 1 contains 1024 MB (Premium) DIMMS (enabled)


Integral SCSI controller 2: Version QL1280, low voltage differential


Integral SCSI controller 3: Version QL1280, low voltage differential


Integral SCSI controller 0: Version QL12160, low voltage differential


Disk drive: unit 1 on SCSI controller 0 (unit 1)


Disk drive: unit 2 on SCSI controller 0 (unit 2)


Integral SCSI controller 1: Version QL12160, single ended


CDROM: unit 4 on SCSI controller 1


IOC3/IOC4 serial port: tty1


IOC3/IOC4 serial port: tty2


IOC3 parallel port: plp1


###Graphics board: V10


Graphics board: V12


Integral Fast Ethernet: ef0, version 1, module 001c01, pci 4


Iris Audio Processor: version MAD revision 1, number 1


PCI Adapter ID (vendor 0x1077, device 0x1280) PCI slot 1


PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1


PCI Adapter ID (vendor 0x1412, device 0x1724) PCI slot 2


PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4


PCI Adapter ID (vendor 0x1045, device 0xc861) PCI slot 5


HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)


IP35prom in Module 001c01/Slot n0: Revision 6.210


USB controller: type OHCI

/usr/gfx/gfxinfo -vv

Code: Select all


###Graphics board 0 is "ODYSSEY" graphics.


###        Managed (":0.0") 1920x1200


###        BUZZ version B.2


###        PB&J version 1


###        32MB memory


###                Banks: 2, CAS latency: 3


###         Monitor 0 type: SGX 4352


###        Input Sync: Voltage - Video Level; Source - Internal; Genlocked - False


###        Channel 0:


###         Origin = (0,0)


###         Video Output: 1920 pixels, 1200 lines, 60.02Hz (1920x1200_60)


###         Video Format Flags:  (none)


###         Sync Disabled


###         Using Gamma Map 0


###         Monitor Type:  SGI-4352


###         Gain (all color components) - 0.000000 ; range [1,10]


Graphics board 0 is "ODYSSEY" graphics.


Managed (":0.0") 1920x1200


BUZZ version B.1


PB&J version 1


128MB memory


Banks: 4, CAS latency: 3


Compositor port 1 attached to channel 0 nic 0x1004a768


CMP:  No NIC serial number available.


Monitor 0 type: DEL -4075


Input Sync: Voltage - Video Level; Source - Internal; Genlocked - False


Channel 0:


Origin = (0,0)


Video Output: 1920 pixels, 1200 lines, 60.00Hz (1920x1200_60p)


Video Format Flags:  (none)


Sync Disabled


Using Gamma Map 0


Monitor Type:  DEL-61461


Gain (all color components) - 0.000000 ; range [1,10][/i]

uname -aR

Code: Select all


IRIX64 fuel 6.5 6.5.30m 07202013 IP35

scsicontrol -i /dev/scsi/*

Code: Select all


/dev/scsi/sc0d1l0:  Disk          ModusLnkMXO3367SC800600SM108


ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing


Device is  ready


/dev/scsi/sc0d2l0:  Disk          SGI     HUS103014FL3600 SF00


ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing


Device is  ready


/dev/scsi/sc1d4l0:  CD-ROM        TOSHIBA DVD-ROM SD-M14011F09


ANSI vers 2, ISO ver: 0, ECMA ver: 0; supports:  synch linkedcmds


Device is  not ready

/sbin/diskpatch -v

Code: Select all


sc0d1l0:  Disk         ModusLnkMXO3367SC800600SM108  Serial: ML000024


sc0d2l0:  Disk         SGI     HUS103014FL3600 SF00  Serial: V5VBZUGA

Finally, thanks to ratfink and its hinv output , some l1 commands I couldn't have guessed by myself ;-)

l1cmd serial all

Code: Select all


Data                            Location      Value


------------------------------  ------------  --------


Local System Serial Number      EEPROM        08:00:69:10:7C:A7


Local Brick Serial Number       EEPROM        NCJ712


Reference Brick Serial Number   NVRAM         NCJ712






EEPROM      Product Name    Serial         Part Number           Rev  T/W


----------  --------------  -------------  --------------------  ---  ------


NODE        IP34            NCJ712         030_1707_004          C    00


MAC         MAC ADDRESS     NA             NA                    NA   NA


PIMM        IP34PIMM        NNN514         030_1932_001          B    00


###XIO         ASTODYV10       NSR498         030_1826_003          A    00


XIO         ASTODY          MLD922         030_1726_003          E    00




EEPROM     JEDEC-SPD Info           Part Number        Rev  Speed  SGI


---------- ------------------------ ------------------ ---- ------ --------


DIMM 0     CE000000000000000C989800 M3 46L2820DT2-CA0   2D   10.0  N/A


DIMM 2     no hardware detected


DIMM 1     CE000000000000000C7F9800 M3 46L2820DT2-CA0   2D   10.0  N/A


DIMM 3     no hardware detected

l1cmd flash status

Code: Select all


Flash image B currently booted




Image      Status        Revision    Built


-----   -------------   ----------   -----


A     valid           1.40.4       09/29/2005 13:43:39


B     default         1.40.4       09/29/2005 13:43:39

l1cmd env

Code: Select all


Environmental monitoring is enabled and running.




Description    State       Warning Limits     Fault Limits       Current


-------------- ----------  -----------------  -----------------  -------


12V    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.125


12V IO    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.125


5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.096


3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.320


2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.470


1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.466


5V AUX    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.096


3.3V AUX    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.285


PIMM 12V BIAS    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.125


SRAM    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.496


VCPU    Enabled  10%   1.13/  1.38  20%   1.00/  1.50    1.255


PIMM 1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.495


PIMM 3.3V AUX    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.268


PIMM 5V AUX    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.096


XIO 12V BIAS    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.000


XIO 5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.070


XIO 2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.457


XIO 3.3V AUX    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.285




Description     State       Warning RPM  Current RPM


--------------- ----------  -----------  -----------


FAN  0  EXHAUST    Enabled          920         1188


FAN  1       HD    Enabled         1560         2122


FAN  2      PCI    Enabled         1120         1534


FAN  3    XIO 1    Enabled         1600         2721


FAN  4    XIO 2    Enabled         1600         2596


FAN  5       PS    Enabled         1349         3276




Advisory   Critical   Fault      Current


Description       State       Temp       Temp       Temp       Temp


----------------- ----------  ---------  ---------  ---------  ---------


0 NODE 0            Enabled    [Autofan Control]    80C/176F   40C/104F


1 NODE 1            Enabled    [Autofan Control]    80C/176F   41C/105F


2 NODE 2            Enabled    [Autofan Control]    80C/176F   32C/ 89F


3 PIMM              Enabled    [Autofan Control]    80C/176F   47C/116F


4 ODYSSEY           Enabled    [Autofan Control]    80C/176F   45C/113F


5 BEDROCK           Enabled    [Autofan Control]    85C/185F   44C/111F

Hope you like it.

BetXen

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

smj
From Berkeley, CA, USA, NA, Earth, Sol
Who joined Nov. 12, 2007, 7:54 p.m.

Wrote the following at May 4, 2011, 2:16 a.m...

Wow, great machine! Which manufacturer is the drive identifying itself with the tag "ModusLnk" from, Fujitsu? Some indication this is the case from a quick Google search, but not definitive...

Then?

... Now?

+MLA

... Other: DEC :BA213:

Sun , DG AViiON , NeXT :Cube:

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote the following at May 4, 2011, 3:39 a.m...

It is a Fujitsu Worldisk, 36GB. I'll have a look at it this evening and give you more details soon. Maybe Ian will read this post and could answer better and faster than me.

If someone wonders what monitor I have, here is tha answer: GDM-FW9011. Sgi 24" 16:10 CRT weighting more than 50kg. My back still remembers (I used to live on the 5th floor without elevator).

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

smj
From Berkeley, CA, USA, NA, Earth, Sol
Who joined Nov. 12, 2007, 7:54 p.m.

Wrote the following at May 4, 2011, 12:38 p.m...

BetXen wrote: GDM-FW9011. Sgi 24" 16:10 CRT weighting more than 50kg. My back still remembers (I used to live on the 5th floor without elevator).

No doubt! I lived in a 6th floor walk-up in Manhattan for four years in the mid- to late-90s, and around the end of the first year had a monstrous Idek Iiyama 21" w/ motorized tilt/swivel base delivered. (I hope I tipped well for that delivery!) When I left I had movers deal with it, thank goodness...

Then?

... Now?

+MLA

... Other: DEC :BA213:

Sun , DG AViiON , NeXT :Cube:

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote the following at May 4, 2011, 2:19 p.m...

So... the hard disk label says:

Code: Select all


Capacity          36.7GB


RPM               15000


Interface         SCSI 80 PIN


MODEL             MX03367SC800600S

You were right !

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

[[C|-|E]]
From London - UK
Who joined March 2, 2011, 1:37 a.m.

Wrote the following at May 5, 2011, 9:35 a.m...

It would be very nice to show some pics of that great machine

_ Betty Blue _
R12000A 400 Mhz ; 1 Gb RAM ; 72 Gb 15K HDD; IRIX 6.5.29
CrystalEyes; Dial Box; O2Cam "ZEYE"; external Toshiba SD-M1711 DVD-ROM; Octane speakers;
Lock bar; SGI microphone.
Mods: PSU Noctua fan; internal Toshiba SD-M1401 DVD-ROM; Adaptec AIC-7880P SCSI card.

_ REKIEM_I7 _
Seasonic X 1250W PSU / Intel I7 2600k 4 x 5,00 Ghz / 2 x Gainward 2Gb GTX 560Ti Phantom 2 / 32 Gb DDR3 / Intel x25-M 160 Gb SSD and 10 extra Tb
_ REKIEM_T5400 _
875W PSU / 2 x Intel Xeon Harpertown 4 x 3,33 Ghz / 1 x EVGA Geforce 4Gb GTX 980 Supercloked / 32 Gb DDR2 667 ECC / Samsung 840 Series Pro 128GB SSD and 3 extra Tb
_ Raspberry Pi _

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote the following at May 5, 2011, 9:41 a.m...

I'll try to take some this evening... stay tuned !

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote the following at May 8, 2011, 2:57 p.m...

As promised, here are some pics of my new toy and its friends... made in a hurry as I will leave for a business trip tomorrow morning. I'll take better pictures later.

: One corner of my actual computer room

: My new fuel in good company

: All the sgi now in my hands

See you.

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

smj
From Berkeley, CA, USA, NA, Earth, Sol
Who joined Nov. 12, 2007, 7:54 p.m.

Wrote the following at May 9, 2011, 4:14 p.m...

Nice lair. And wow, intact Origin 200 plastic! Now, how do we go about duplicating them...?

Then?

... Now?

+MLA

... Other: DEC :BA213:

Sun , DG AViiON , NeXT :Cube:

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote the following at May 10, 2011, 9:20 a.m...

"Nice lair" you said... yes, because I've juste made order before the photo. Normally it's significantly more messy

Regarding the O200, the skins WERE perfect when they were given to me, as the O200 was used in my university and never moved since their installation. Unfortunately I didn't know the plastics were so fragile and tilted one of the towers during a move. Two feet immediately broke, so I had to remove the two others. Finaly, one door "axis" broke too, but on the other module... grrrr !

Anyway, If you know how to make them reproduce, give me a call ! It would be funny to have a baby O200 as paperweight...

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

jan-jaap
From Wijchen, The Netherlands
Who joined June 17, 2004, 11:35 a.m.

Wrote the following at May 11, 2011, 12:46 a.m...

BetXen wrote: "Nice lair" you said... yes, because I've juste made order before the photo. Normally it's significantly more messy

Regarding the O200, the skins WERE perfect when they were given to me, as the O200 was used in my university and never moved since their installation. Unfortunately I didn't know the plastics were so fragile and tilted one of the towers during a move. Two feet immediately broke, so I had to remove the two others. Finaly, one door "axis" broke too, but on the other module... grrrr !

Anyway, If you know how to make them reproduce, give me a call ! It would be funny to have a baby O200 as paperweight...

When I got my O200, two or three of it's feet were attached with double sided tape

I drilled a hole through the 'foot hinge' and with a bolt + nut it's now stronger than when it was new.

Now this is a deep dark secret, so everybody keep it quiet

It turns out that when reset, the WD33C93 defaults to a SCSI ID of 0, and it was simpler to leave it that way... -- Dave Olson, in comp.sys.sgi
Currently in commercial service:

(2x)

In the museum : almost every MIPS/IRIX system.
Wanted : GM1 board for Professional Series GT graphics (030-0076-003, 030-0076-004)

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote the following at May 11, 2011, 12:55 a.m...

Good idea. I'll try that. They are already broken, so I can't do worse...

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .

smj
From Berkeley, CA, USA, NA, Earth, Sol
Who joined Nov. 12, 2007, 7:54 p.m.

Wrote the following at May 11, 2011, 10:19 a.m...

BetXen wrote: Anyway, If you know how to make them reproduce, give me a call ! It would be funny to have a baby O200 as paperweight...

Well I don't, but fellow nekochanner sgifanatic has been developing aluminum skins for the IRIS Indigo in this thread - it's long, but stick with it and you'll see some amazing replacement parts.

Then?

... Now?

+MLA

... Other: DEC :BA213:

Sun , DG AViiON , NeXT :Cube:

PymbleSoftware
From P.O. Box 121, Pymble, Sydney, NSW 2073, Australia.
Who joined July 15, 2008, 5:48 p.m.

Wrote the following at May 11, 2011, 2:42 p.m...

smj wrote:

BetXen wrote: Anyway, If you know how to make them reproduce, give me a call ! It would be funny to have a baby O200 as paperweight...

Well I don't, but fellow nekochanner sgifanatic has been developing aluminum skins for the IRIS Indigo in this thread - it's long, but stick with it and you'll see some amazing replacement parts.

I used to dabble in plastic

R.

死の神はりんごだけ食べる

開いた括弧は必ず閉じる -- あるプログラマー

:Tezro:

J5600, 2 x Mac, 3 x SUN, Alpha DS20E, Alpha 800 5/550, 3 x RS/6000, Amiga 4000 VideoToaster, Amiga4000 -030, 733MHz Sam440 AmigaOS 4.1 update 1.

Sold: :Indy:

Tandem Himalaya S-Series Nonstop S72000 ServerNet.

Twitter @PymbleSoftware
Current Apps (iOS) -> https://itunes.apple.com/au/artist/pymb ... d553990081
(Android) https://play.google.com/store/apps/deve ... +Ltd&hl=en
(Onyx2) Cortex ---> http://www.facebook.com/pages/Cortex-th ... 11?sk=info
(0300s) Minnie ---> http://www.facebook.com/pages/Minnie-th ... 02?sk=info
Github ---> https://github.com/pymblesoftware

BetXen
From Vevey, Switzerland
Who joined Sept. 21, 2004, 12:05 p.m.

Wrote the following at May 11, 2011, 11:58 p.m...

I just read you old topic PS. At work, we'll probably buy a Faro 3D digitizer in a near future. If my collegues from the metrology let me use it, I could maybe give you the dimensions of a o200 skins, even a 3d model if I found enough time to process the data.

We'll see in a few weeks or months.

: oxygen / :A3504L:

: neon (16xItanium2 1.6, L2 9MB) / :O200:

: beryllium
:Fuel:

: nitrogen / :Octane2:

: carbon / :Octane:

: fluorine
:O2:

: hydrogen (R10k 195, 512Mo) / :O2:

: sodium (R5k 180, 512Mo) / :O2:

: R5k 180->200 motherboard and PM only
:Indigo2IMP:

: helium (R10k 195, HighImpact, 160Mo) / :Indigo2IMP:

: boron /

: magnesium
:4D70G:

4D70GT : hydrogen, my very first one (now property of musée bolo and the foundation mémoires informatiques )
See the hinv/gfxinfo posts here .