Nekonomicon

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of [resolved] Irix suddenly very very slow. at March 30, 2009, 4:34 a.m...

I don't know why, this morning I switched on my octane, but it is very slower than the other days.
I didn't install anything before, I can hear the hdd scratching a lot now.., I have already had this problem, I reinstalled Irix and it was resolved, but now, I can't reinstall it until I finish to set up a Linux-server to share Irix cds.

How I can repair my system?

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of [resolved] Irix suddenly very very slow. at March 30, 2009, 5:32 a.m...

Thanks, I found "configmon" that it was using more 320Mb of RAM

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of editing movies and special effects ? at Aug. 3, 2009, 1:08 a.m...

I wanna use my octane to create my own movies with softwares like m$ moviemaker.
So I don't know what are the names of theses softwares on IRIX. And I 'll be happy to found one that can use xvid or mpg and mpg-2 codecs.

And which software to create some special effects ?

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of Realsoft 3D v5.1 for IRIX at Sept. 23, 2009, 8:57 a.m...

I've installed realsoft 3D 5.1.26 beta, but when I wanna run it I've got Bus error due to an incompatible libpng version: I have libpng-1.2.8 and r3d required 1.0.15

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of neko perl spamassassin at Oct. 5, 2009, 6:41 a.m...

it doesn't work for me

Code: Select all


   ./dieplaneten-sgi
   

   GLUT: Fatal Error in dieplaneten-sgi: visual with necessary capabilities not found.

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of neko perl spamassassin at Oct. 5, 2009, 7:55 a.m...

Octane with IRIX 6.5.30f.

Code: Select all


   hinv
   

   1 250 MHZ IP30 Processor
   

   CPU: MIPS R10000 Processor Chip Revision: 3.4
   

   FPU: MIPS R10010 Floating Point Chip Revision: 0.0
   

   Main memory size: 384 Mbytes
   

   Xbow ASIC: Revision 1.3
   

   Instruction cache size: 32 Kbytes
   

   Data cache size: 32 Kbytes
   

   Secondary unified instruction/data cache size: 1 Mbyte
   

   Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
   

   Disk drive: unit 1 on SCSI controller 0
   

   Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
   

   IOC3/IOC4 serial port: tty1
   

   IOC3/IOC4 serial port: tty2
   

   IOC3 parallel port: plp1
   

   Graphics board: ESI
   

   Integral Fast Ethernet: ef0, version 1, pci 2
   

   Iris Audio Processor: version RAD revision 12.0, number 1
   

   

   glxinfo
   

   display: :0
   

   server glx vendor string: SGI
   

   server glx version string: 1.3 Irix 6.5
   

   server glx extensions (GLX_):
   

   EXT_import_context, EXT_visual_info, EXT_visual_rating,
   

   SGI_make_current_read, SGI_swap_control, SGI_video_sync, SGIX_fbconfig,
   

   SGIX_pbuffer, SGIX_swap_group.
   

   client glx version 1.3
   

   client glx extensions (GLX_):
   

   EXT_import_context, EXT_visual_info, EXT_visual_rating,
   

   SGI_make_current_read, SGI_swap_control, SGI_video_sync, SGIX_fbconfig,
   

   SGIX_pbuffer, SGIX_swap_group.
   

   OpenGL vendor string: SGI
   

   OpenGL renderer string: IMPACT/1/1/0
   

   OpenGL version string: 1.1 Irix 6.5
   

   OpenGL extensions (GL_):
   

   EXT_abgr, EXT_blend_color, EXT_blend_logic_op, EXT_blend_minmax,
   

   EXT_blend_subtract, EXT_convolution, EXT_copy_texture, EXT_histogram,
   

   EXT_packed_pixels, EXT_polygon_offset, EXT_subtexture, EXT_texture,
   

   EXT_texture3D, EXT_texture_object, EXT_vertex_array, SGI_color_matrix,
   

   SGI_color_table, SGI_texture_color_table, SGIS_texture_filter4,
   

   SGIX_list_priority, SGIX_texture_scale_bias.
   

   glu version: 1.3 Irix 6.5
   

   glu extensions (GLU_):
   

   EXT_abgr, EXT_nurbs_tessellator, EXT_object_space_tess, EXT_packed_pixels,
   

   EXT_texture, SGI_filter4_parameters.
   

   

   visual  x  bf lv rg d st  r  g  b a  ax dp st accum buffs  ms
   

   id dep cl sp sz l  ci b ro sz sz sz sz bf th cl  r  g  b  a ns b
   

   -----------------------------------------------------------------
   

   0x20  8 pc  .  8  . c  .  .  .  .  .  .  .  .  .  .  .  .  .  . .
   

   0x22  8 pc  y  8  1 c  .  .  .  .  .  .  .  .  .  .  .  .  .  . .
   

   0x23  8 pc  .  8  1 c  .  .  .  .  .  .  .  .  .  .  .  .  .  . .
   

   0x24 12 pc  . 12  . b  .  . 12  .  .  .  .  .  .  .  .  .  .  . .
   

   0x25 12 pc  . 12  . b  y  . 12  .  .  .  .  .  .  .  .  .  .  . .
   

   0x26 12 tc  . 16  . r  y  .  4  4  4  4  .  .  . 16 16 16 16  . .
   

   0x27 15 tc  . 16  . r  y  .  5  5  5  1  .  .  . 16 16 16 16  . .
   

   0x28 24 tc  . 32  . r  .  .  8  8  8  8  .  .  . 16 16 16 16  . .

I use a custom resolution (1680x1050) with 24bits colors.

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of neko perl spamassassin at Oct. 6, 2009, 5:12 a.m...

I found why it doesn't work: my 1680x1050 file has smoething wrong. it works when I switch to 1280x1024_60 standard resolution

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of neko perl spamassassin at Oct. 6, 2009, 5:47 a.m...

It didn't work with my last 1680x1050_60 file, and nor celestia and blender worked. I try 1280x1024_60. it works, but I don't know why, I have blue sun with die-planeten.

I re-create a 1680x1050_60. celestia, blender and die-planeten run, but I have a lot of artfacts and stanges colors.
I'll try the cube
celestia

cube

die-planeten

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of neko perl spamassassin at Oct. 6, 2009, 8:27 a.m...

that changes nothing

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of windows nt for mips? at Dec. 26, 2009, 1:23 a.m...

Hi,
I know we can find winNT 3.x or 4.O for mips cpus. Can I install it on a SGI octane? If yes, by LAN?

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of windows nt for mips? at Dec. 26, 2009, 2:46 a.m...

thanx, I'd like to try another system with a gui than IRIX

nuts
Member
Who joined Nov. 3, 2008, 12:27 p.m.
and authored 86 notes

Wrote on the subject of Could it be possible to make a full gnu/irix system? at Feb. 23, 2010, 10:10 a.m...

My question is, if it's possible to use a gnu system with IRIX kernel with basic IRIX's tools like software manager, chkconfig... We could keep coherence with GPL softwares. No?

nuts
Member
Who joined Nov. 3, 2008, 12:27 p.m.
and authored 86 notes

Wrote on the subject of Could it be possible to make a full gnu/irix system? at Feb. 23, 2010, 12:59 p.m...

I think to a system that's using Irix kernel and base tools, with GNU bases and only gpl softwares in /bin /usr/bin etc... xorg ...
With a system like that, maybe it will be easier to port softwares on mips ?

nuts
Member
Who joined Nov. 3, 2008, 12:27 p.m.
and authored 86 notes

Wrote on the subject of Could it be possible to make a full gnu/irix system? at Feb. 23, 2010, 11:29 p.m...

kshuff wrote:

nuts wrote:

I think to a system that's using Irix kernel and base tools, with GNU bases and only gpl softwares in /bin /usr/bin etc... xorg ...
With a system like that, maybe it will be easier to port softwares on mips ?

When are you going to get started?

I don't know, I've no tools do make it yet. If I have time, I think I'll try.

I know about vpro and xorg, but I don't know about MGRAS performance with xorg.

nuts
Member
Who joined Nov. 3, 2008, 12:27 p.m.
and authored 86 notes

Wrote on the subject of Prefix-portage from Gentoo on IRIX at April 7, 2010, 9:41 a.m...

I try to install portage but, after creating account, folders and unpack mipspro-wrapper, I have:

Code:

  bash-4.0$ source .bashrc
  
  STDPATH="$PATH"
  
  export PATH="$EPREFIX/tmp/usr/bin:$EPREFIX/tmp/bin:$PATH"
  
  $./bootstrap-prefix.sh $EPREFIX tree
  
  * Bootstrapping Gentoo prefixed portage installation using
  
  * host:   mips-sgi-irix6.5
  
  * prefix: /opt/gentoo
  
  * ready to bootstrap tree
  
  * Fetching prefix-overlay-20100323.tar.bz2
  
  http://prefix.gentooexperimental.org/distfiles/prefix-overlay-20100323.tar.bz2: Non-recoverable failure in name resolution
  
  ftp>

nuts
Member
Who joined Nov. 3, 2008, 12:27 p.m.
and authored 86 notes

Wrote on the subject of OpenBSD works on SGI now at April 9, 2010, 1:02 a.m...

I'm trying to install OpenBSD 4.7 (beta) on octane, it boots with the framebuffer and the keyboard works, but I have a panic, it can't "mount root", then I don't understand the error

edit: woops, I think I use the bad image, I'll try again

nuts
Member
Who joined Nov. 3, 2008, 12:27 p.m.
and authored 86 notes

Wrote on the subject of OpenBSD works on SGI now at April 9, 2010, 6:11 a.m...

I see, I used bsd.IP30, I'll retry tomorrow

nuts
Member
Who joined Nov. 3, 2008, 12:27 p.m.
and authored 86 notes

Wrote on the subject of OpenBSD works on SGI now at April 9, 2010, 7:30 a.m...

Why not, they support hp-ux and solaris binaries... but I don't know if it will be a good feature because IRIX softwares are old now.

But it could be fun to use qemu and emulate a x86 to run a windows: maybe better than softwindows95

nuts
Member
Who joined Nov. 3, 2008, 12:27 p.m.
and authored 86 notes

Wrote on the subject of OpenBSD works on SGI now at April 9, 2010, 9:29 p.m...

mea culpa, it'b a good feature. I don't know if 3d acceleration is available with Xorg, but Vpro could be supported with Openbsd 4.7 (I can't test, I have a MGRAS)

nuts
Member
Who joined Nov. 3, 2008, 12:27 p.m.
and authored 86 notes

Wrote on the subject of OpenBSD works on SGI now at April 10, 2010, 12:13 a.m...

I'm retrying with the correct file now bsd.rd.IP30, the installation is in progress, I set a default configuration about the harddrive, wait and see.

edit:

It works, but I don't know how to configure the prom to boot (I use bootp for the moment) and I'm searching how to configure Xorg

edit2: It's resolved for the boot, I've set the OSLoader to "boot"

edit3: There's no driver for xorg, so I try http://www.linuxtogo.org/~florian/files ... 00.tar.bz2

edit4: the system is easy to install and it's fast to boot. pkg_add works fine, but for the moment no X (I fail when I try to compile the Impact driver) and /usr/ports doesn't exist

edit5: I'm installing ports maybe it could help me for impact driver. and bsd boots in video

nuts
Member
Who joined Nov. 3, 2008, 12:27 p.m.
and authored 86 notes

Wrote on the subject of OpenBSD works on SGI now at April 10, 2010, 12:32 p.m...

In the video the first track was Soulfly-"Cangaceiro" and after it's Rammstein-"Asche. Zu Asche"

For the driver I'll try the last released if I can.

nuts
Who joined Nov. 3, 2008, 11:27 a.m.
and authored 104 notes

Wrote on the subject of OpenBSD/sgi at Aug. 29, 2010, 1:12 a.m...

what's new in the current snapshot for IP30 (x11...?)
where can we read news for mips status?

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of OpenBSD works on SGI now at Nov. 21, 2010, 10 a.m...

My LG L225WS works too

the 2 screens are 22"

nuts
Who joined Nov. 3, 2008, 11:27 a.m.
and authored 104 notes

Wrote on the subject of OpenBSD/sgi at Nov. 21, 2010, 11:02 p.m...

no chance.
If you check on the ftp in snapshots releases you can see it's not 4.9 yet

ftp://ftp.eu.openbsd.org/pub/OpenBSD/snapshots/sgi/

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of OpenBSD works on SGI now at Nov. 23, 2010, 1:40 a.m...

Yes I have a basic 13w3 adapter bought on internet, I had already this monitor so, I have just tried and it works.
After checking by google, my LGs are SOG:

Code: Select all


   Panel     TN
   

   Size    22W
   

   Resolution    1680 x 1050
   

   Pixel Pitch    0.2767 x 0.2767
   

   Brightness    300 cd/㎡
   

   Contrast Ratio    1000:1
   

   Viewing Angle    170˚/170˚
   

   Response Time    5ms
   

   Display Colors    16.7M
   

   Sync Range
   

   Horizontal Frequency    30 ~ 83 kHz
   

   Vertical Frequency    56 ~ 75 Hz
   

   Input Signal
   

   Video Signal    RGB Analog
   

   Sync type    Separate, Composite, SOG
   

   Connectors
   

   PC    15 Pin D-sub
   

   Plug & Play
   

   DDC    DDC/CI
   

   Power Supply    AC 90~264 V (47 ~ 63Hz)
   

   Power Consumption
   

   On    45W
   

   Stand-by / Suspend    1W
   

   DPM Off    1W
   

   User Control
   

   Button    6ea(Power Key Included)
   

   Type    Tact Type
   

   Mechanical
   

   Dimension(W x H x D)    501.7 x 423.5 x 233.9 mm
   

   Weight    5.65kg
   

   Stand    Tilt, Swivel, Base detachable
   

   Rack    VESA 100 x 100
   

   Regulations
   

   Safety    TCO03, UL(cUL), TUV-Type, SEMKO
   

   EMC    FCC-B, CE
   

   Power saving    EPA Energy Star

nuts
Who joined Nov. 3, 2008, 11:27 a.m.
and authored 104 notes

Wrote on the subject of OpenBSD/sgi at Dec. 31, 2010, 12:14 a.m...

not yet.
I don't know if miod has started to make a driver in the actual snapshot.

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of Unable using LAN in PROM at Jan. 7, 2011, 8:22 a.m...

When I stop to the maintenance I can't use the LAN so I can"t install systems on my octane.
If I boot on IRIX, the network works well, but in the Prom, I'm unable to ping py others computers. I try "resetenv" and reset the netaddr and srvaddr but no changes: it doesn't work!

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of Unable using LAN in PROM at Jan. 7, 2011, 11:16 p.m...

I've made a virtual machine that runs ubuntu amd64 for a server install. and it doesn"t work. I retry with DINA now to check if it works

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of Unable using LAN in PROM at Jan. 8, 2011, 6:17 a.m...

resolved i had a bad configuration file on my tftpd server

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of MaXX Desktop DR3 at Jan. 9, 2011, 6:09 a.m...

I've reinstalled maxx DR3 just for fun, I have no icons on desktop. Finally how to change the wallpaper ?

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of fun with network install onto clean disk at Jan. 15, 2011, 2:28 a.m...

up, I m trying to setup a Install server on virtualbox with freeBSD 8.1. I read the wiki and I've modified the inetd.conf file.

My octane can't run fx or start the installation. Unable to execute bootp...: invalid argument. unable to load bootp... is not a valid file to boot

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of fun with network install onto clean disk at Jan. 16, 2011, 12:32 a.m...

I tried DINA on virtualbox and it didn't work. And I don't know why, I had not network with vmware

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of Some Nekowares crash! at May 2, 2011, 9:24 a.m...

Hi,
I don't know why and I searched but I didn't find a solution, some softwares don't work like pidgin, gimp...
I've just re-installed IRIX 6.5.30f and I don't understand:

Code: Select all


   octane 1% cd /usr/nekoware/bin/
   

   octane 2% ./gimp
   

   Fontconfig error: Cannot load default config file
   

   No fonts found; this probably means that the fontconfig
   

   library is not correctly configured. You may need to
   

   edit the fonts.conf configuration file. More information
   

   about fontconfig can be found in the fontconfig(3) manual
   

   page and on http://fontconfig.org
   

   octane 3%
   

   octane 3% ./pidgin
   

   Fontconfig error: Cannot load default config file
   

   No fonts found; this probably means that the fontconfig
   

   library is not correctly configured. You may need to
   

   edit the fonts.conf configuration file. More information
   

   about fontconfig can be found in the fontconfig(3) manual
   

   page and on http://fontconfig.org

edit: I've reinstalled pango and fontconfig and it works

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of Remote Irix and Cygwin at Nov. 3, 2011, 1:39 p.m...

I have installed Cygwin on my PC to use my Octane without screen.
I check the fontserver is on and I've modified the xdm-config like the wiki but:

It's really ugly. Faster than the sgi GPU but ugly ugly ugly.

The fonts are not correct and the colors too bad.
I tried to use Xnest but I have:

Code: Select all


   Xnest :1-query octane
   

   Fatal server error:
   

   Unable to open display "".

edit: it works better with X command instead of Xnest

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of Linux on a O2 at Feb. 22, 2013, 11:58 a.m...

there is a debian port

http://www.cyrius.com/debian/o2/

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of RESOLVED tardist and decompression. at Nov. 15, 2013, 9:41 a.m...

I have just re-install Irix in my Octane from a Debian server.
I've downloaded some nekowares on my server and I can't decompress them.
tar xvf doesnot work.

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of RESOLVED tardist and decompression. at Nov. 15, 2013, 10:01 a.m...

Doesn't work, sfwmanager said that a I don't have any packages.
If I put SERVER:/srv/tftp/neko where are my nekos.tardist, sfwmanager said there aren't files

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of RESOLVED tardist and decompression. at Nov. 15, 2013, 10:50 a.m...

all of nekoware, I can't install them if they're compressed with software manager. I'm using Irix 6.5.30.
My debian server, works perfectly: I can install Irix or OpenBSD, inst and software manager open all of directories that contain install files, but not my nekoware's directory because all file are compressed in tardist.

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of RESOLVED tardist and decompression. at Nov. 15, 2013, 11:59 a.m...

jimmer wrote: tardist's are regular uncompressed tar-archives. simply untar them on your debian server:

tar -xvf rara.tardist -C .

Code: Select all


   tar: neko_zsh-4.3.9.tardist: not found in archive

vishnu wrote: The file program will tell you if they're really tar files or not. If file can't tell what they are they were probably corrupted somewhere in the download and all you should need to do is download them again.

My downloads are ok, to test, I have untar from Irix and it works, but not from Debian. My harddrive in my octane is about 8Gb, too small, that's why I stock nekowares in a server.

nuts
Who joined Nov. 3, 2008, 11:27 a.m.

Wrote on the subject of RESOLVED tardist and decompression. at Nov. 15, 2013, 12:02 p.m...

Resolved:

Code: Select all


   for file in ls *.tardist; do tar -xvf $file; done

The collected works of nuts - Page 1