The collected works of pan1k

I also tried getting this to work. It didn't. I tried to build partiview manually but no go. I was too tired last night to keep working on it. It looks like a really nice app. It coredumps on me though

hinv:

1 400 MHZ IP30 Processor
CPU: MIPS R12000 Processor Chip Revision: 3.5
FPU: MIPS R12010 Floating Point Chip Revision: 0.0
Main memory size: 1280 Mbytes
Xbow ASIC: Revision 1.4
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 2 Mbytes
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
Disk drive: unit 1 on SCSI controller 0
Disk drive: unit 2 on SCSI controller 0
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V6
Integral Fast Ethernet: ef0, version 1, pci 2
Iris Audio Processor: version RAD revision 12.0, number 1

gfxinfo:

Graphics board 0 is "ODYSSEY" graphics.
Managed (":0.0") 1280x720
BUZZ version A.1
PB&J version 1
32MB memory
Banks: 2, CAS latency: 3
Monitor 0 type: Unknown
Channel 0:
Origin = (0,0)
Video Output: 1280 pixels, 720 lines, 72.00Hz (1280x720_72)

I got Homebank to compile on my Octane2. It's a simple account manager, nothing like gnucash, but I used to use Homebank on my Amiga. My problem is, it compiles fine, but complains about the SVG files that are used within Homebank. I installed librsvg from nekoware, still doesn't work, so I tried opening it with GIMP, won't load it either.

Anyone have any ideas?

I'm trying to compile MLDonkey and I get this error:

squirrel 77# gmake
/usr/nekoware/bin/ocamlc.opt -linkall -o ocamlpp.byte -custom unix.cma str.cma -ccopt " " -cclib "-lz " -cclib "-lpthread" -I build tools/ocamlpp.cmo
sh: c99: not found
Error while building custom runtime system
gmake: *** [ocamlpp.byte] Error 2

I'm trying to get the VGA font so BitchX will look correct. Does anyone have it, or know where to get it?

Worked like a charm! I googled all over the place looking for fonts. Thanks again.. now if I only had decent Flash support my octane would rock.. thanks to this site this machine is my daily driver!

Hey guys, I'm selling my Octane2. I'm in Socal, near LA if you want to pick it up local. Here's the specs:

Octane2 R12000 @ 400MHZ
1.25GB RAM
2 74GB Drives
1 External 32X Toshiba CD-ROM - Mounted in Sun 611 case
V6 Pro Graphics

Also has installation media. Everything works fine, I just need to sell some toys for my move.

chrisc24atgmail.com - remove the 'at' if you would like to get ahold of me.

I'm selling my SGI Octane2. I need space in my new studio apartment. Here are the specs:

400MHZ R12000 CPU
2 74GB 10,000 RPM SCSI Drives
V6 Pro Graphics (32MB)
External Sun CDROM 32x
1.25GB of RAM
Blue LED Lightbar

Asking $200 OBO. Will deliver within 25 miles of Los Angeles. Skin is in great shape and door is intact. Have a few demo CD's I can toss in also...

Hey guys! I brought my SGI to work so I wont have to pay for the electric bill but it won't display any video now. Do you think all 3 monitors are unable to sync? One of them displays the login screen for a sec then goes to standby mode. I tried going in through the console and resetting it, but I can't even get into the diagnostics screen when you first turn the machine on. Any ideas? At home I have a 19" Sony Trinitron...

I got in through the serial port and setmon'd a 1024x768 @ 75HZ. Doesnt do anything. Even when the machine first turns on, the screen is black. I'm guessing somehow the 13W3 Adaptor went bad... I can buy another one when I get paid next. It's either that or the V6 Pro board is going out.. *sigh*

The monitors at work are: ViewSonic, Mitsubishi and NEC.. none work...

Hey guys I got a freebie 18GB Cheetah, I put it in the tray, pushed it in, but disk manager isn't recognizing it.. how do I get it to see the third drive? Any infos is appreciated!

Hey guys..

I'm trying to run QuakeI on my Octane2. It's got V6PRO Graphics and 1.2GBRAM. When I run the quake executable, it defaults to the none GL versions. Is that how it's supposed to be? When I run the GL version, it gets laggy and then crashes my system. Any tips out there for Quake to run right? I'm using the port from SGI.

I have an HP 9000 735. I tried to install NeXTSTEP 3.3 on it, got it to install on an external drive. I get the NeXTSTEP boot screen, checking disks, blah blah.. then a kernel problem something about the jupiter audio onboard. then it stops and reboots the machine. I tried reinstalling, same problem. Is my cpu board bad??

I have 144MB of RAM, Firmware is 2.6, 99MHZ CPU and CRX24 graphics.

Yep, it's a 735. Soooo close!