Nekonomicon - Origin 300. 24xR14000 600MHz. 22GB. Onyx4 skins

bjornl
Who joined May 9, 2006, 10:55 a.m.
and authored 309 notes

Wrote the following at March 2, 2013, 8:40 a.m...

*UPDATED hinv etc at the end of the post*

I finally got time to put this machine together. I picked up the Origin 300 parts almost two years ago and had plans to put it inside my old Clariion rack but I never finished that.
Four months ago I got a half height Onyx4 rack that has just enough space for these parts. This last month I have put it together and placed it with the other big iron. The rack comes from kais58.

Unfortunately module 001c16 is not working and I think it is mainboard related, "no response". I have tried swapping boards with the other modules, but the problem stays with the 001c16 module.
The leds on the back, that I assume show cpu activity, are not active at all, and one (of two) numalink led on the router for this module is not lit.
I traded an extra module from ramq. An IO9 swap with this didn't help, and I was thinking to replace the whole module with this 2x500Mhz, but I prefer another 4x600Mhz so I must find a replacement mainboard.

A nice replacement would be an Origin 350 with graphics hack and get an "Onyx 300".

Short hinv

Code:

  O300 1# hinv
  
  20 600 MHZ IP35 Processors
  
  CPU: MIPS R14000 Processor Chip Revision: 2.4
  
  FPU: MIPS R14010 Floating Point Chip Revision: 2.4
  
  Main memory size: 20480 Mbytes
  
  Instruction cache size: 32 Kbytes
  
  Data cache size: 32 Kbytes
  
  Secondary unified instruction/data cache size: 4 Mbytes
  
  Integral SCSI controller 10: Version Fibre Channel QL2310
  
  Integral SCSI controller 4: Version Fibre Channel QL2310
  
  Integral SCSI controller 11: Version QL12160, low voltage differential
  
  Integral SCSI controller 12: Version QL12160, low voltage differential
  
  Integral SCSI controller 15: Version QL12160, low voltage differential
  
  Integral SCSI controller 13: Version QL12160, low voltage differential
  
  Integral SCSI controller 16: Version QL12160, low voltage differential
  
  Integral SCSI controller 14: Version QL12160, low voltage differential
  
  Integral SCSI controller 8: Version QL12160, low voltage differential
  
  Integral SCSI controller 9: Version QL12160, low voltage differential
  
  Integral SCSI controller 0: Version QL12160, single ended
  
  Disk drive: unit 1 on SCSI controller 0
  
  Integral SCSI controller 1: Version QL12160, low voltage differential
  
  Disk drive: unit 1 on SCSI controller 1
  
  Disk drive: unit 2 on SCSI controller 1
  
  Disk drive: unit 3 on SCSI controller 1
  
  Disk drive: unit 4 on SCSI controller 1
  
  IOC3/IOC4 serial port: tty9
  
  IOC3/IOC4 serial port: tty10
  
  IOC3/IOC4 serial port: tty11
  
  IOC3/IOC4 serial port: tty13
  
  IOC3/IOC4 serial port: tty3
  
  IOC3/IOC4 serial port: tty12
  
  IOC3/IOC4 serial port: tty14
  
  IOC3/IOC4 serial port: tty4
  
  IOC3/IOC4 serial port: tty7
  
  IOC3/IOC4 serial port: tty8
  
  Fast Ethernet: ef2, version 1, module 001c14, pci 4
  
  Fast Ethernet: ef4, version 1, module 001c22, pci 4
  
  Fast Ethernet: ef3, version 1, module 001c18, pci 4
  
  Fast Ethernet: ef1, version 1, module 001c24, pci 4
  
  Integral Fast Ethernet: ef0, version 1, module 001c12, pci 4
  
  Iris Audio Processor: version EMU revision A4, number 1
  
  IOC3/IOC4 external interrupts: 3
  
  IOC3/IOC4 external interrupts: 5
  
  IOC3/IOC4 external interrupts: 4
  
  IOC3/IOC4 external interrupts: 2
  
  IOC3/IOC4 external interrupts: 1
  
  USB controller: type OHCI
  
  USB controller: type OHCI
  
  USB controller: type OHCI
  
  USB controller: type OHCI
  
  USB controller: type OHCI

Long hinv

Code:

  O300 2# hinv -vm
  
  Location: /hw/module/001c12/node
  
  IP45_4CPU Board: barcode MPX630     part 030-1797-001 rev -B
  
  Location: /hw/module/001c12/Ibrick/xtalk/14
  
  IO8 Board: barcode MPZ202     part 030-1673-004 rev -C
  
  Location: /hw/module/001c12/Ibrick/xtalk/15
  
  IO8 Board: barcode MPZ202     part 030-1673-004 rev -C
  
  Location: /hw/module/001c14/node
  
  IP45_4CPU Board: barcode MPX638     part 030-1797-001 rev -B
  
  Location: /hw/module/001c14/Ibrick/xtalk/14
  
  IO8 Board: barcode MPZ212     part 030-1673-004 rev -C
  
  Location: /hw/module/001c14/Ibrick/xtalk/15
  
  IO8 Board: barcode MPZ212     part 030-1673-004 rev -C
  
  Location: /hw/module/001c18/node
  
  IP45_4CPU Board: barcode MPX653     part 030-1797-001 rev -B
  
  Location: /hw/module/001c18/Ibrick/xtalk/14
  
  IO8 Board: barcode MRE740     part 030-1673-004 rev -C
  
  Location: /hw/module/001c18/Ibrick/xtalk/15
  
  IO8 Board: barcode MRE740     part 030-1673-004 rev -C
  
  Location: /hw/module/001c22/node
  
  IP45_4CPU Board: barcode MPX659     part 030-1797-001 rev -B
  
  Location: /hw/module/001c22/Ibrick/xtalk/14
  
  IO8 Board: barcode MRE719     part 030-1673-004 rev -C
  
  Location: /hw/module/001c22/Ibrick/xtalk/15
  
  IO8 Board: barcode MRE719     part 030-1673-004 rev -C
  
  Location: /hw/module/001c24/node
  
  IP45_4CPU Board: barcode MPX656     part 030-1797-001 rev -B
  
  Location: /hw/module/001c24/Ibrick/xtalk/14
  
  IO8 Board: barcode MRG051     part 030-1673-004 rev -C
  
  Location: /hw/module/001c24/Ibrick/xtalk/15
  
  IO8 Board: barcode MRG051     part 030-1673-004 rev -C
  
  Location: /hw/module/001r20/router
  
  ROUTER Board: barcode MAN493     part 030-1634-003 rev -A
  
  20 600 MHZ IP35 Processors
  
  CPU: MIPS R14000 Processor Chip Revision: 2.4
  
  FPU: MIPS R14010 Floating Point Chip Revision: 2.4
  
  CPU 0 at Module 001c12/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 1 at Module 001c12/Slot 0/Slice B: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 2 at Module 001c12/Slot 0/Slice C: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 3 at Module 001c12/Slot 0/Slice D: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 4 at Module 001c14/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 5 at Module 001c14/Slot 0/Slice B: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 6 at Module 001c14/Slot 0/Slice C: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 7 at Module 001c14/Slot 0/Slice D: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 8 at Module 001c18/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 9 at Module 001c18/Slot 0/Slice B: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 10 at Module 001c18/Slot 0/Slice C: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 11 at Module 001c18/Slot 0/Slice D: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 12 at Module 001c22/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 13 at Module 001c22/Slot 0/Slice B: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 14 at Module 001c22/Slot 0/Slice C: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 15 at Module 001c22/Slot 0/Slice D: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 16 at Module 001c24/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 17 at Module 001c24/Slot 0/Slice B: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 18 at Module 001c24/Slot 0/Slice C: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 19 at Module 001c24/Slot 0/Slice D: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  Main memory size: 20480 Mbytes
  
  Instruction cache size: 32 Kbytes
  
  Data cache size: 32 Kbytes
  
  Secondary unified instruction/data cache size: 4 Mbytes
  
  Memory at Module 001c12/Slot 0: 4096 MB (enabled)
  
  Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 2 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 3 contains 1024 MB (Premium) DIMMS (enabled)
  
  Memory at Module 001c14/Slot 0: 4096 MB (enabled)
  
  Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 2 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 3 contains 1024 MB (Premium) DIMMS (enabled)
  
  Memory at Module 001c18/Slot 0: 4096 MB (enabled)
  
  Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 2 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 3 contains 1024 MB (Premium) DIMMS (enabled)
  
  Memory at Module 001c22/Slot 0: 4096 MB (enabled)
  
  Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 2 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 3 contains 1024 MB (Premium) DIMMS (enabled)
  
  Memory at Module 001c24/Slot 0: 4096 MB (enabled)
  
  Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 2 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 3 contains 1024 MB (Premium) DIMMS (enabled)
  
  ROUTER in Module 001c12/Slot 0: Revision 1: Active Ports [1,4,5,7,8] (enabled)
  
  Integral SCSI controller 10: Version Fibre Channel QL2310, 66 MHz PCI
  
  Integral SCSI controller 4: Version Fibre Channel QL2310, 66 MHz PCI
  
  Integral SCSI controller 11: Version QL12160, low voltage differential
  
  Integral SCSI controller 12: Version QL12160, low voltage differential
  
  Integral SCSI controller 15: Version QL12160, low voltage differential
  
  Integral SCSI controller 13: Version QL12160, low voltage differential
  
  Integral SCSI controller 16: Version QL12160, low voltage differential
  
  Integral SCSI controller 14: Version QL12160, low voltage differential
  
  Integral SCSI controller 8: Version QL12160, low voltage differential
  
  Integral SCSI controller 9: Version QL12160, low voltage differential
  
  Integral SCSI controller 0: Version QL12160, single ended
  
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
  
  Integral SCSI controller 1: Version QL12160, low voltage differential
  
  Disk drive: unit 1 on SCSI controller 1 (unit 1)
  
  Disk drive: unit 2 on SCSI controller 1 (unit 2)
  
  Disk drive: unit 3 on SCSI controller 1 (unit 3)
  
  Disk drive: unit 4 on SCSI controller 1 (unit 4)
  
  IOC3/IOC4 serial port: tty9
  
  IOC3/IOC4 serial port: tty10
  
  IOC3/IOC4 serial port: tty11
  
  IOC3/IOC4 serial port: tty13
  
  IOC3/IOC4 serial port: tty3
  
  IOC3/IOC4 serial port: tty12
  
  IOC3/IOC4 serial port: tty14
  
  IOC3/IOC4 serial port: tty4
  
  IOC3/IOC4 serial port: tty7
  
  IOC3/IOC4 serial port: tty8
  
  Fast Ethernet: ef2, version 1, module 001c14, pci 4
  
  Fast Ethernet: ef4, version 1, module 001c22, pci 4
  
  Fast Ethernet: ef3, version 1, module 001c18, pci 4
  
  Fast Ethernet: ef1, version 1, module 001c24, pci 4
  
  Integral Fast Ethernet: ef0, version 1, module 001c12, pci 4
  
  Iris Audio Processor: version EMU revision A4, number 1
  
  PCI Adapter ID (vendor 0x1077, device 0x2300) PCI slot 2
  
  PCI Adapter ID (vendor 0x1102, device 0x0004) PCI slot 1
  
  PCI Adapter ID (vendor 0x1102, device 0x7003) PCI slot 1
  
  PCI Adapter ID (vendor 0x1102, device 0x4001) PCI slot 1
  
  PCI Adapter ID (vendor 0x1077, device 0x2300) PCI slot 2
  
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
  
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
  
  PCI Adapter ID (vendor 0x11c1, device 0x5802) PCI slot 5
  
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
  
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
  
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
  
  PCI Adapter ID (vendor 0x11c1, device 0x5802) PCI slot 5
  
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
  
  PCI Adapter ID (vendor 0x11c1, device 0x5802) PCI slot 5
  
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
  
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
  
  PCI Adapter ID (vendor 0x11c1, device 0x5802) PCI slot 5
  
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
  
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
  
  PCI Adapter ID (vendor 0x11c1, device 0x5802) PCI slot 5
  
  IOC3/IOC4 external interrupts: 3
  
  IOC3/IOC4 external interrupts: 5
  
  IOC3/IOC4 external interrupts: 4
  
  IOC3/IOC4 external interrupts: 2
  
  IOC3/IOC4 external interrupts: 1
  
  HUB in Module 001c12/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
  
  HUB in Module 001c14/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
  
  HUB in Module 001c18/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
  
  HUB in Module 001c22/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
  
  HUB in Module 001c24/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
  
  IP35prom in Module 001c12/Slot n0: Revision 6.210
  
  IP35prom in Module 001c14/Slot n0: Revision 6.210
  
  IP35prom in Module 001c18/Slot n0: Revision 6.210
  
  IP35prom in Module 001c22/Slot n0: Revision 6.210
  
  IP35prom in Module 001c24/Slot n0: Revision 6.210
  
  USB controller: type OHCI
  
  USB controller: type OHCI
  
  USB controller: type OHCI
  
  USB controller: type OHCI
  
  USB controller: type OHCI

And now some pictures

Attachment:

O3000_ONYX4_outside.jpg [ 234.28 KiB | Viewed 882 times ]

Attachment:

O3000_ONYX4_inside.jpg [ 252.51 KiB | Viewed 882 times ]

Since most men like backsides, I'll include one of that as well

The door is missing.

Attachment:

O3000_ONYX4_backside.jpg [ 321.27 KiB | Viewed 882 times ]

All of this is running from a single phase 220V 16A. The original connector is still there.

Attachment:

O3000_ONYX4_power.jpg [ 191.44 KiB | Viewed 882 times ]

Next step is to hook it up to the IR2 module and get an Onyx 300, hinv-wise. The observant reader might have seen the audio board in the hinv. It's an Audigy2 ZS, same as the Fuel can use.

foetz
Who joined April 14, 2003, 3:34 a.m.
and authored 4732 notes

Wrote the following at March 2, 2013, 9:21 a.m...

what a nice mix. looking at the background it seems you're not shy on ip27 racks and more

_________________
r-a-c.de

ramq
Who joined Jan. 25, 2008, 6:06 a.m.
and authored 760 notes

Wrote the following at March 2, 2013, 11:50 a.m...

Nice system!

_________________
:O3200:

smj
Who joined Nov. 12, 2007, 7:54 p.m.
and authored 1013 notes

Wrote the following at March 2, 2013, 5:02 p.m...

bjornl wrote:

Since most men like backsides, I'll include one of that as well

Speaking only for myself, I appreciate a nice rack too... :mrgreen:

Glad to see kais58's cabinet going to good use. Nice work.

_________________
Then? :IRIS3130:

... Now?

-

+MLA

... Other: DEC :BA213:

Sun , DG AViiON , NeXT :Cube:

hamei
Who joined Feb. 24, 2004, 4:10 p.m.
and authored 8705 notes

Wrote the following at March 2, 2013, 7:09 p.m...

bjornl wrote:

Four months ago I got a half height Onyx4 rack that has just enough space for these parts.

Lovely looking thing, isn't she ?

Quote:

A nice replacement would be an Origin 350 with graphics hack and get an "Onyx 3000".

With all the cpus you have, I'd replace that brick and one more with a V-brick or X-modded-to-V-brick. Then you could have four V-12's ... just enough to drive a T221. Or two V-12's and one of those nice Eizo dual-input displays.

I am definitely jealous

mia
Who joined Feb. 19, 2003, 1:54 p.m.
and authored 877 notes

Wrote the following at March 2, 2013, 8:04 p.m...

Yes, I admit, very very nice system.

How much power does it draw?

_________________
:Onyx2:

Pontus
Who joined May 8, 2008, 11:12 a.m.
and authored 503 notes

Wrote the following at March 3, 2013, 3:43 a.m...

Super sexy!

_________________
:Onyx2R:

<- MicroVAX 3500 :BA213:

<- DECsystem 5500 :BA215:

<- MicroVAX 3300
Pictures of my collection: www.pdp8.se

recondas
Moderator
Who joined June 6, 2004, 4:55 p.m.
and authored 4968 notes

Wrote the following at March 3, 2013, 7:41 a.m...

It is a very nice system - congratulations.

When the opportunity arises, please consider adding some or all of the additional info smj mentions in the Hinv Forum sticky "Guidelines for "hinv"-Thread". The additional detail/info can be invaluable when troubleshooting problems or tracking down the random listed-by-part-number-only eBay posts. Here's a snip from Steve's post:

Code:

  uname -a (-aR if appropriate)
  
  scsicontrol -i /dev/scsi/* (change path as needed)
  
  /sbin/diskpatch -v
  
  L1/L2 serial all
  
  L1/L2 flash status
  
  L1/L2 env
  
  L1/L2 pci

If there's not already one in there, there should be a mount built into the top of the rack to hold an L2 controller . If you don't already have one, an L2 controller is a very nice addition to a multi-module system (and you could also add an L2 touch-screen display ). EDIT: Looks like 'already have an L2' is indeed the case - just took a closer look at your photo of the rear of the rack and it looks like there are some cables running up to the L2 area.

bjornl wrote:

Next step is to hook it up to the IR2 module and get an Onyx 3000

You're probably way ahead of me, but if your IR2 module has a Ktown(1), you'll likely want to swap in a Ktown2.

_________________
***********************************************************************
Welcome to ARMLand - 0/0x0d00
running...(sherwood-root 0607201829)
* InfiniteReality/Reality Software, IRIX 6.5 Release *
***********************************************************************

bjornl
Who joined May 9, 2006, 10:55 a.m.
and authored 309 notes

Wrote the following at March 9, 2013, 9:08 a.m...

Thank you all. I like that color a lot and the half height rack makes it almost a deskside. Some graphics inside and it would be perfect.
I haven't seen to many V- or X-brick around, so maybe an modded O350 will be easier (and cheaper) way to go. Also, the ones I have seen is not 220V and I don't have a powerbrick (or whatever it is called).
I will probably settle with V10 graphics, because of V12 prices, if I get to this point.

I will measure the power consumption when I find my meter and add some details to the info as recondas recommends.

There is indeed an L2, and a controller display would be neat, but again not so easy to come by I think.

The Ktown2 is waiting in a box, ready to swap in :-)

It has been pointed out to me that it is in fact Origin 300, not Origin 3000, so I fixed that typo in the original post.

mia
Who joined Feb. 19, 2003, 1:54 p.m.
and authored 877 notes

Wrote the following at March 9, 2013, 9:19 a.m...

If you get around it, please tell us what the power consumption is like...

Thanks!

_________________
:Onyx2:

vishnu
Who joined March 18, 2007, 2:25 p.m.
and authored 1165 notes

Wrote the following at March 9, 2013, 1:04 p.m...

Even if you had a backdoor how would you ever get it closed? :shock:

_________________
Project:
Movin' on up, toooo the east side
Plan:
World domination! Or something...

sgtprobe
Who joined Nov. 20, 2008, 11:18 p.m.
and authored 297 notes

Wrote the following at June 6, 2013, 2:41 p.m...

OH, that's one hot looking machine

/Jonas

_________________

-----------------
Old polygon wrangler
___________________
http://www.edgeloop.se

bjornl
Who joined May 9, 2006, 10:55 a.m.
and authored 309 notes

Wrote the following at June 30, 2013, 1:17 a.m...

Thank you.

I have just replaced the faulty mainboard in module 001c16, and now all 24 cpus are working :-)

I had my eye on one on eBay, and also got a tip about it from jan-jaap.
I first tried to just swap the VRMs and IO9 from another module, but it didn't help, so it was the mainboard after all.
Unfortunately there is also some problem with one of the DIMMs, which causes me to "loose" 2GB. So now I have to find a replacement 1GB DIMM. Has anyone a leftover?

Code:

  ************************************************
  
  TOO MANY ERRORS IN MAIN MEMORY TEST: DimmPair:  1
  
  DIMMs:     2 & 3
  
  Bank:      1
  
  There were 4 errors found.
  
  mtest_bank_main failed: Base Address
  
  RSLT mtest_bank_mai FAIL                diag_rc = 43  Base Address
  
  TOO MANY ERRORS DURING MEMORY BIST: DimmPair:  1
  
  DIMMs:     2 & 3
  
  Bank:      1
  
  There were 8 errors found.
  
  mtest_bank_bist failed:
  
  RSLT mtest_bank_bis FAIL                diag_rc = 48
  
  Disabling the failed bank

Regarding power consumption, it is like this:

Code:

  Power on router+L2 44W
  
  Power on all,but in standby 90W
  
  Power on all 1270W
  
  After boot 1360W
  
  Four disks in TP900 110W

There is no load on the cpus in this measurements. Maybe I'll check power consumption again when I do some benchmarking.

Anyway here are updated hinv's and some more information.

Short hinv

Code:

  O300 1# hinv
  
  24 600 MHZ IP35 Processors
  
  CPU: MIPS R14000 Processor Chip Revision: 2.4
  
  FPU: MIPS R14010 Floating Point Chip Revision: 2.4
  
  Main memory size: 22528 Mbytes
  
  Instruction cache size: 32 Kbytes
  
  Data cache size: 32 Kbytes
  
  Secondary unified instruction/data cache size: 4 Mbytes
  
  Integral SCSI controller 10: Version Fibre Channel QL2310
  
  Integral SCSI controller 4: Version Fibre Channel QL2310
  
  Integral SCSI controller 11: Version QL12160, low voltage differential
  
  Integral SCSI controller 12: Version QL12160, low voltage differential
  
  Integral SCSI controller 13: Version QL12160, low voltage differential
  
  Integral SCSI controller 14: Version QL12160, low voltage differential
  
  Integral SCSI controller 15: Version QL12160, low voltage differential
  
  Integral SCSI controller 16: Version QL12160, low voltage differential
  
  Integral SCSI controller 8: Version QL12160, low voltage differential
  
  Integral SCSI controller 9: Version QL12160, low voltage differential
  
  Integral SCSI controller 0: Version QL12160, single ended
  
  Disk drive: unit 1 on SCSI controller 0
  
  Integral SCSI controller 1: Version QL12160, low voltage differential
  
  Disk drive: unit 1 on SCSI controller 1
  
  Disk drive: unit 2 on SCSI controller 1
  
  Disk drive: unit 3 on SCSI controller 1
  
  Disk drive: unit 4 on SCSI controller 1
  
  Integral SCSI controller 17: Version QL12160, low voltage differential
  
  Integral SCSI controller 18: Version QL12160, low voltage differential
  
  IOC3/IOC4 serial port: tty9
  
  IOC3/IOC4 serial port: tty10
  
  IOC3/IOC4 serial port: tty11
  
  IOC3/IOC4 serial port: tty13
  
  IOC3/IOC4 serial port: tty12
  
  IOC3/IOC4 serial port: tty14
  
  IOC3/IOC4 serial port: tty3
  
  IOC3/IOC4 serial port: tty4
  
  IOC3/IOC4 serial port: tty7
  
  IOC3/IOC4 serial port: tty8
  
  IOC3/IOC4 serial port: tty15
  
  IOC3/IOC4 serial port: tty16
  
  Gigabit Ethernet: tg1, module 001c16, PCI bus 2 slot 2
  
  Fast Ethernet: ef2, version 1, module 001c14, pci 4
  
  Fast Ethernet: ef3, version 1, module 001c18, pci 4
  
  Fast Ethernet: ef4, version 1, module 001c22, pci 4
  
  Fast Ethernet: ef1, version 1, module 001c24, pci 4
  
  Integral Fast Ethernet: ef0, version 1, module 001c12, pci 4
  
  Fast Ethernet: ef5, version 1, module 001c16, pci 4
  
  Iris Audio Processor: version EMU revision A4, number 1
  
  IOC3/IOC4 external interrupts: 3
  
  IOC3/IOC4 external interrupts: 4
  
  IOC3/IOC4 external interrupts: 5
  
  IOC3/IOC4 external interrupts: 2
  
  IOC3/IOC4 external interrupts: 1
  
  IOC3/IOC4 external interrupts: 6
  
  USB controller: type OHCI
  
  USB controller: type OHCI
  
  USB controller: type OHCI
  
  USB controller: type OHCI
  
  USB controller: type OHCI
  
  USB controller: type OHCI

Long hinv

Code:

  O300 2# hinv -vm
  
  Location: /hw/module/001c12/node
  
  IP45_4CPU Board: barcode MPX630     part 030-1797-001 rev -B
  
  Location: /hw/module/001c12/Ibrick/xtalk/14
  
  IO8 Board: barcode MPZ202     part 030-1673-004 rev -C
  
  Location: /hw/module/001c12/Ibrick/xtalk/15
  
  IO8 Board: barcode MPZ202     part 030-1673-004 rev -C
  
  Location: /hw/module/001c14/node
  
  IP45_4CPU Board: barcode MPX638     part 030-1797-001 rev -B
  
  Location: /hw/module/001c14/Ibrick/xtalk/14
  
  IO8 Board: barcode MPZ212     part 030-1673-004 rev -C
  
  Location: /hw/module/001c14/Ibrick/xtalk/15
  
  IO8 Board: barcode MPZ212     part 030-1673-004 rev -C
  
  Location: /hw/module/001c16/node
  
  IP45_4CPU Board: barcode MRB025     part 030-1797-001 rev -B
  
  Location: /hw/module/001c16/Ibrick/xtalk/14
  
  IO8 Board: barcode MPA329     part 030-1673-004 rev -C
  
  Location: /hw/module/001c16/Ibrick/xtalk/15
  
  IO8 Board: barcode MPA329     part 030-1673-004 rev -C
  
  Location: /hw/module/001c18/node
  
  IP45_4CPU Board: barcode MPX653     part 030-1797-001 rev -B
  
  Location: /hw/module/001c18/Ibrick/xtalk/14
  
  IO8 Board: barcode MRE740     part 030-1673-004 rev -C
  
  Location: /hw/module/001c18/Ibrick/xtalk/15
  
  IO8 Board: barcode MRE740     part 030-1673-004 rev -C
  
  Location: /hw/module/001c22/node
  
  IP45_4CPU Board: barcode MPX659     part 030-1797-001 rev -B
  
  Location: /hw/module/001c22/Ibrick/xtalk/14
  
  IO8 Board: barcode MRE719     part 030-1673-004 rev -C
  
  Location: /hw/module/001c22/Ibrick/xtalk/15
  
  IO8 Board: barcode MRE719     part 030-1673-004 rev -C
  
  Location: /hw/module/001c24/node
  
  IP45_4CPU Board: barcode MPX656     part 030-1797-001 rev -B
  
  Location: /hw/module/001c24/Ibrick/xtalk/14
  
  IO8 Board: barcode MRG051     part 030-1673-004 rev -C
  
  Location: /hw/module/001c24/Ibrick/xtalk/15
  
  IO8 Board: barcode MRG051     part 030-1673-004 rev -C
  
  Location: /hw/module/001r20/router
  
  ROUTER Board: barcode MAN493     part 030-1634-003 rev -A
  
  24 600 MHZ IP35 Processors
  
  CPU: MIPS R14000 Processor Chip Revision: 2.4
  
  FPU: MIPS R14010 Floating Point Chip Revision: 2.4
  
  CPU 0 at Module 001c12/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 1 at Module 001c12/Slot 0/Slice B: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 2 at Module 001c12/Slot 0/Slice C: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 3 at Module 001c12/Slot 0/Slice D: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 4 at Module 001c14/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 5 at Module 001c14/Slot 0/Slice B: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 6 at Module 001c14/Slot 0/Slice C: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 7 at Module 001c14/Slot 0/Slice D: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 8 at Module 001c16/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 9 at Module 001c16/Slot 0/Slice B: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 10 at Module 001c16/Slot 0/Slice C: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 11 at Module 001c16/Slot 0/Slice D: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 12 at Module 001c18/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 13 at Module 001c18/Slot 0/Slice B: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 14 at Module 001c18/Slot 0/Slice C: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 15 at Module 001c18/Slot 0/Slice D: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 16 at Module 001c22/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 17 at Module 001c22/Slot 0/Slice B: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 18 at Module 001c22/Slot 0/Slice C: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 19 at Module 001c22/Slot 0/Slice D: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 20 at Module 001c24/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 21 at Module 001c24/Slot 0/Slice B: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 22 at Module 001c24/Slot 0/Slice C: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  CPU 23 at Module 001c24/Slot 0/Slice D: 600 Mhz MIPS R14000 Processor Chip (enabled)
  
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
  
  Main memory size: 22528 Mbytes
  
  Instruction cache size: 32 Kbytes
  
  Data cache size: 32 Kbytes
  
  Secondary unified instruction/data cache size: 4 Mbytes
  
  Memory at Module 001c12/Slot 0: 4096 MB (enabled)
  
  Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 2 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 3 contains 1024 MB (Premium) DIMMS (enabled)
  
  Memory at Module 001c14/Slot 0: 4096 MB (enabled)
  
  Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 2 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 3 contains 1024 MB (Premium) DIMMS (enabled)
  
  Memory at Module 001c16/Slot 0: 2048 MB (enabled)
  
  Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 2 contains 1024 MB (Premium) DIMMS (disabled)
  
  Bank 3 contains 1024 MB (Premium) DIMMS (disabled)
  
  Memory at Module 001c18/Slot 0: 4096 MB (enabled)
  
  Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 2 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 3 contains 1024 MB (Premium) DIMMS (enabled)
  
  Memory at Module 001c22/Slot 0: 4096 MB (enabled)
  
  Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 2 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 3 contains 1024 MB (Premium) DIMMS (enabled)
  
  Memory at Module 001c24/Slot 0: 4096 MB (enabled)
  
  Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 2 contains 1024 MB (Premium) DIMMS (enabled)
  
  Bank 3 contains 1024 MB (Premium) DIMMS (enabled)
  
  ROUTER in Module 001c12/Slot 0: Revision 1: Active Ports [1,4,5,6,7,8] (enabled)
  
  Integral SCSI controller 10: Version Fibre Channel QL2310, 66 MHz PCI
  
  Integral SCSI controller 4: Version Fibre Channel QL2310, 66 MHz PCI
  
  Integral SCSI controller 11: Version QL12160, low voltage differential
  
  Integral SCSI controller 12: Version QL12160, low voltage differential
  
  Integral SCSI controller 13: Version QL12160, low voltage differential
  
  Integral SCSI controller 14: Version QL12160, low voltage differential
  
  Integral SCSI controller 15: Version QL12160, low voltage differential
  
  Integral SCSI controller 16: Version QL12160, low voltage differential
  
  Integral SCSI controller 8: Version QL12160, low voltage differential
  
  Integral SCSI controller 9: Version QL12160, low voltage differential
  
  Integral SCSI controller 0: Version QL12160, single ended
  
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
  
  Integral SCSI controller 1: Version QL12160, low voltage differential
  
  Disk drive: unit 1 on SCSI controller 1 (unit 1)
  
  Disk drive: unit 2 on SCSI controller 1 (unit 2)
  
  Disk drive: unit 3 on SCSI controller 1 (unit 3)
  
  Disk drive: unit 4 on SCSI controller 1 (unit 4)
  
  Integral SCSI controller 17: Version QL12160, low voltage differential
  
  Integral SCSI controller 18: Version QL12160, low voltage differential
  
  IOC3/IOC4 serial port: tty9
  
  IOC3/IOC4 serial port: tty10
  
  IOC3/IOC4 serial port: tty11
  
  IOC3/IOC4 serial port: tty13
  
  IOC3/IOC4 serial port: tty12
  
  IOC3/IOC4 serial port: tty14
  
  IOC3/IOC4 serial port: tty3
  
  IOC3/IOC4 serial port: tty4
  
  IOC3/IOC4 serial port: tty7
  
  IOC3/IOC4 serial port: tty8
  
  IOC3/IOC4 serial port: tty15
  
  IOC3/IOC4 serial port: tty16
  
  Gigabit Ethernet: tg1, module 001c16, PCI bus 2 slot 2
  
  Fast Ethernet: ef2, version 1, module 001c14, pci 4
  
  Fast Ethernet: ef3, version 1, module 001c18, pci 4
  
  Fast Ethernet: ef4, version 1, module 001c22, pci 4
  
  Fast Ethernet: ef1, version 1, module 001c24, pci 4
  
  Integral Fast Ethernet: ef0, version 1, module 001c12, pci 4
  
  Fast Ethernet: ef5, version 1, module 001c16, pci 4
  
  Iris Audio Processor: version EMU revision A4, number 1
  
  PCI Adapter ID (vendor 0x1077, device 0x2300) PCI slot 2
  
  PCI Adapter ID (vendor 0x14e4, device 0x1645) PCI slot 2
  
  PCI Adapter ID (vendor 0x1102, device 0x0004) PCI slot 1
  
  PCI Adapter ID (vendor 0x1102, device 0x7003) PCI slot 1
  
  PCI Adapter ID (vendor 0x1102, device 0x4001) PCI slot 1
  
  PCI Adapter ID (vendor 0x1077, device 0x2300) PCI slot 2
  
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
  
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
  
  PCI Adapter ID (vendor 0x11c1, device 0x5802) PCI slot 5
  
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
  
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
  
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
  
  PCI Adapter ID (vendor 0x11c1, device 0x5802) PCI slot 5
  
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
  
  PCI Adapter ID (vendor 0x11c1, device 0x5802) PCI slot 5
  
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
  
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
  
  PCI Adapter ID (vendor 0x11c1, device 0x5802) PCI slot 5
  
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
  
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
  
  PCI Adapter ID (vendor 0x11c1, device 0x5802) PCI slot 5
  
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
  
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
  
  PCI Adapter ID (vendor 0x11c1, device 0x5802) PCI slot 5
  
  IOC3/IOC4 external interrupts: 3
  
  IOC3/IOC4 external interrupts: 4
  
  IOC3/IOC4 external interrupts: 5
  
  IOC3/IOC4 external interrupts: 2
  
  IOC3/IOC4 external interrupts: 1
  
  IOC3/IOC4 external interrupts: 6
  
  HUB in Module 001c12/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
  
  HUB in Module 001c14/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
  
  HUB in Module 001c16/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
  
  HUB in Module 001c18/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
  
  HUB in Module 001c22/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
  
  HUB in Module 001c24/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
  
  IP35prom in Module 001c12/Slot n0: Revision 6.210
  
  IP35prom in Module 001c14/Slot n0: Revision 6.210
  
  IP35prom in Module 001c16/Slot n0: Revision 6.210
  
  IP35prom in Module 001c18/Slot n0: Revision 6.210
  
  IP35prom in Module 001c22/Slot n0: Revision 6.210
  
  IP35prom in Module 001c24/Slot n0: Revision 6.210
  
  USB controller: type OHCI
  
  USB controller: type OHCI
  
  USB controller: type OHCI
  
  USB controller: type OHCI
  
  USB controller: type OHCI
  
  USB controller: type OHCI

Additional information

Code:

  O300 3# uname -aR
  
  IRIX64 O300 6.5 6.5.30m 07202013 IP35

Code:

  O300 4# scsicontrol -i /sev/scsi/*
  
  /dev/scsi/sc0d1l0:  Disk          SGI     IBM  DGHS09Y    0190
  
  ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing
  
  Device is  ready
  
  /dev/scsi/sc1d1l0:  Disk          COMPAQ  BD1468A4C5      HPB4
  
  ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing
  
  Device is  ready
  
  /dev/scsi/sc1d2l0:  Disk          COMPAQ  BD1468A4C5      HPB4
  
  ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing
  
  Device is  ready
  
  /dev/scsi/sc1d3l0:  Disk          COMPAQ  BD1468856B      HPB2
  
  ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing
  
  Device is  ready
  
  /dev/scsi/sc1d4l0:  Disk          COMPAQ  BD1468A4C5      HPB4
  
  ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing
  
  Device is  ready

Code:

  O300 5# /sbin/diskpatch -v
  
  sc0d1l0:  Disk         SGI     IBM  DGHS09Y    0190  Serial: 68AE3DAA
  
  sc1d1l0:  Disk         COMPAQ  BD1468A4C5      HPB4  Serial: 3KA4J9AA
  
  sc1d2l0:  Disk         COMPAQ  BD1468A4C5      HPB4  Serial: 3KA416AA
  
  sc1d3l0:  Disk         COMPAQ  BD1468856B      HPB2  Serial: D4AB0BAA
  
  sc1d4l0:  Disk         COMPAQ  BD1468A4C5      HPB4  Serial: 3KA4NFAA

Code:

  M2100545-001-L2>serial all
  
  001c12:
  
  Data                            Location      Value
  
  ------------------------------  ------------  --------
  
  Local System Serial Number      NVRAM         M2100545
  
  Reference System Serial Number  Attached L2   M2100545
  
  Local Brick Serial Number       EEPROM        MPX630
  
  Reference Brick Serial Number   NVRAM         MPX630
  
  EEPROM      Product Name    Serial      Part Number           Rev  T/W
  
  ----------  --------------  ----------  --------------------  ---  ------
  
  NODE        IP45_4CPU       MPX630      030_1797_001          B    00
  
  IO8         IO8             MPZ202      030_1673_004          C    00
  
  EEPROM      JEDEC Info                Part Number         Rev  Speed (ns)
  
  ----------  ------------------------  ------------------  ---  ----------
  
  DIMM 0      CE000000000000000C322E00  M3 46L2820DT2-CA0   2D    10.0
  
  DIMM 2      CE000000000000000C4A2E00  M3 46L2820DT2-CA0   2D    10.0
  
  DIMM 1      CE000000000000000C332D00  M3 46L2820DT2-CA0   2D    10.0
  
  DIMM 3      CE000000000000000C4C2E00  M3 46L2820DT2-CA0   2D    10.0
  
  001c14:
  
  Data                            Location      Value
  
  ------------------------------  ------------  --------
  
  Local System Serial Number      NVRAM         M2100545
  
  Reference System Serial Number  Attached L2   M2100545
  
  Local Brick Serial Number       EEPROM        MPX638
  
  Reference Brick Serial Number   NVRAM         MPX638
  
  EEPROM      Product Name    Serial      Part Number           Rev  T/W
  
  ----------  --------------  ----------  --------------------  ---  ------
  
  NODE        IP45_4CPU       MPX638      030_1797_001          B    00
  
  IO8         IO8             MPZ212      030_1673_004          C    00
  
  EEPROM      JEDEC Info                Part Number         Rev  Speed (ns)
  
  ----------  ------------------------  ------------------  ---  ----------
  
  DIMM 0      CE000000000000000C2A2E00  M3 46L2820DT2-CA0   2D    10.0
  
  DIMM 2      CE000000000000000C342E00  M3 46L2820DT2-CA0   2D    10.0
  
  DIMM 1      CE000000000000000C442E00  M3 46L2820DT2-CA0   2D    10.0
  
  DIMM 3      CE000000000000000C3A2E00  M3 46L2820DT2-CA0   2D    10.0
  
  001c16:
  
  Data                            Location      Value
  
  ------------------------------  ------------  --------
  
  Local System Serial Number      NVRAM         M2100545
  
  Reference System Serial Number  Attached L2   M2100545
  
  Local Brick Serial Number       EEPROM        MRB025
  
  Reference Brick Serial Number   NVRAM         MRB025
  
  EEPROM      Product Name    Serial      Part Number           Rev  T/W
  
  ----------  --------------  ----------  --------------------  ---  ------
  
  NODE        IP45_4CPU       MRB025      030_1797_001          B    00
  
  IO8         IO8             MPA329      030_1673_004          C    00
  
  EEPROM      JEDEC Info                Part Number         Rev  Speed (ns)
  
  ----------  ------------------------  ------------------  ---  ----------
  
  DIMM 0      CE000000000000000C4E2E00  M3 46L2820DT2-CA0   2D    10.0
  
  DIMM 2      CE000000000000000C542E00  M3 46L2820DT2-CA0   2D    10.0
  
  DIMM 1      CE000000000000000C4B2E00  M3 46L2820DT2-CA0   2D    10.0
  
  DIMM 3      CE000000000000000C462E00  M3 46L2820DT2-CA0   2D    10.0
  
  001c18:
  
  Data                            Location      Value
  
  ------------------------------  ------------  --------
  
  Local System Serial Number      NVRAM         M2100545
  
  Reference System Serial Number  Attached L2   M2100545
  
  Local Brick Serial Number       EEPROM        MPX653
  
  Reference Brick Serial Number   NVRAM         MPX653
  
  EEPROM      Product Name    Serial      Part Number           Rev  T/W
  
  ----------  --------------  ----------  --------------------  ---  ------
  
  NODE        IP45_4CPU       MPX653      030_1797_001          B    00
  
  IO8         IO8             MRE740      030_1673_004          C    00
  
  EEPROM      JEDEC Info                Part Number         Rev  Speed (ns)
  
  ----------  ------------------------  ------------------  ---  ----------
  
  DIMM 0      CE000000000000000C362E00  M3 46L2820DT2-CA0   2D    10.0
  
  DIMM 2      7F7FFE00000000001200123D  CM2201B             2     08.0
  
  DIMM 1      CE000000000000000C422E00  M3 46L2820DT2-CA0   2D    10.0
  
  DIMM 3      7F7FFE000000000012001231  CM2201B             2     08.0
  
  001r20:
  
  Data                            Location      Value
  
  ------------------------------  ------------  --------
  
  Local System Serial Number      NVRAM         M2100545
  
  Reference System Serial Number  Attached L2   M2100545
  
  Local Brick Serial Number       EEPROM        MRF019
  
  Reference Brick Serial Number   NVRAM         MRF019
  
  EEPROM      Product Name    Serial      Part Number           Rev  T/W
  
  ----------  --------------  ----------  --------------------  ---  ------
  
  POWER       RPWR            MRF019      030_1631_002          F    00
  
  LOGIC       ROUTER          MAN493      030_1634_003          A    00
  
  001c22:
  
  Data                            Location      Value
  
  ------------------------------  ------------  --------
  
  Local System Serial Number      NVRAM         M2100545
  
  Reference System Serial Number  Attached L2   M2100545
  
  Local Brick Serial Number       EEPROM        MPX659
  
  Reference Brick Serial Number   NVRAM         MPX659
  
  EEPROM      Product Name    Serial      Part Number           Rev  T/W
  
  ----------  --------------  ----------  --------------------  ---  ------
  
  NODE        IP45_4CPU       MPX659      030_1797_001          B    00
  
  IO8         IO8             MRE719      030_1673_004          C    00
  
  EEPROM      JEDEC Info                Part Number         Rev  Speed (ns)
  
  ----------  ------------------------  ------------------  ---  ----------
  
  DIMM 0      CE000000000000000C532E00  M3 46L2820DT2-CA0   2D    10.0
  
  DIMM 2      7F7FFE000000000012001826  CM2201B             2     08.0
  
  DIMM 1      CE000000000000000C562E00  M3 46L2820DT2-CA0   2D    10.0
  
  DIMM 3      7F7FFE000000000012001823  CM2201B             2     08.0
  
  001c24:
  
  Data                            Location      Value
  
  ------------------------------  ------------  --------
  
  Local System Serial Number      NVRAM         M2100545
  
  Reference System Serial Number  Attached L2   M2100545
  
  Local Brick Serial Number       EEPROM        MPX656
  
  Reference Brick Serial Number   NVRAM         MPX656
  
  EEPROM      Product Name    Serial      Part Number           Rev  T/W
  
  ----------  --------------  ----------  --------------------  ---  ------
  
  NODE        IP45_4CPU       MPX656      030_1797_001          B    00
  
  IO8         IO8             MRG051      030_1673_004          C    00
  
  EEPROM      JEDEC Info                Part Number         Rev  Speed (ns)
  
  ----------  ------------------------  ------------------  ---  ----------
  
  DIMM 0      CE000000000000000C5C2E00  M3 46L2820DT2-CA0   2D    10.0
  
  DIMM 2      7F7FFE000000000012001702  CM2201B             2     08.0
  
  DIMM 1      CE000000000000000C522E00  M3 46L2820DT2-CA0   2D    10.0
  
  DIMM 3      7F7FFE000000000012001700  CM2201B             2     08.0

Code:

  M2100545-001-L2>flash status
  
  001c12:
  
  Flash image B currently booted
  
  Image      Status        Revision    Built
  
  -----   -------------   ----------   -----
  
  A     valid           1.18.5       12/18/2002 08:58:31
  
  B     default         1.18.5       12/18/2002 08:58:31
  
  001c14:
  
  Flash image B currently booted
  
  Image      Status        Revision    Built
  
  -----   -------------   ----------   -----
  
  A     valid           1.18.5       12/18/2002 08:58:31
  
  B     default         1.18.5       12/18/2002 08:58:31
  
  001c16:
  
  Flash image A currently booted
  
  Image      Status        Revision    Built
  
  -----   -------------   ----------   -----
  
  A     user default    1.18.5       12/18/2002 08:58:31
  
  B     valid           1.18.5       12/18/2002 08:58:31
  
  001c18:
  
  Flash image B currently booted
  
  Image      Status        Revision    Built
  
  -----   -------------   ----------   -----
  
  A     valid           1.18.5       12/18/2002 08:58:31
  
  B     default         1.18.5       12/18/2002 08:58:31
  
  001r20:
  
  Flash image B currently booted
  
  Image      Status        Revision    Built
  
  -----   -------------   ----------   -----
  
  A     valid           1.18.5       12/18/2002 08:58:31
  
  B     default         1.18.5       12/18/2002 08:58:31
  
  001c22:
  
  Flash image B currently booted
  
  Image      Status        Revision    Built
  
  -----   -------------   ----------   -----
  
  A     valid           1.18.5       12/18/2002 08:58:31
  
  B     default         1.18.5       12/18/2002 08:58:31
  
  001c24:
  
  Flash image B currently booted
  
  Image      Status        Revision    Built
  
  -----   -------------   ----------   -----
  
  A     valid           1.18.5       12/18/2002 08:58:31
  
  B     default         1.18.5       12/18/2002 08:58:31

Code:

  M2100545-001-L2>env
  
  001c12:
  
  Environmental monitoring is enabled and running.
  
  Description    State       Warning Limits     Fault Limits       Current
  
  -------------- ----------  -----------------  -----------------  -------
  
  12V IO    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.19
  
  12V DIG    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.06
  
  5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    4.99
  
  3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.34
  
  5V aux    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    4.91
  
  3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.37
  
  2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.50
  
  Speedo2 CPU    Enabled  10%   1.44/  1.76  20%   1.28/  1.92    1.59
  
  1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.49
  
  Description    State       Warning RPM  Current RPM
  
  -------------- ----------  -----------  -----------
  
  FAN 0     LEFT    Enabled         2160         4007
  
  FAN 1   CENTER    Enabled         2160         4105
  
  FAN 2    RIGHT    Enabled         2160         4105
  
  FAN 3       PS    Enabled         2160         3116
  
  FAN 4      PS'    Enabled         2160         4488
  
  Advisory   Critical   Fault      Current
  
  Description    State       Temp       Temp       Temp       Temp
  
  -------------- ----------  ---------  ---------  ---------  ---------
  
  NODE 0            Enabled   40C/104F   46C/114F   49C/120F   19C/ 66F
  
  NODE 1            Enabled   40C/104F   46C/114F   49C/120F   19C/ 66F
  
  001c14:
  
  Environmental monitoring is enabled and running.
  
  Description    State       Warning Limits     Fault Limits       Current
  
  -------------- ----------  -----------------  -----------------  -------
  
  12V IO    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.25
  
  12V DIG    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.12
  
  5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    4.99
  
  3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.34
  
  5V aux    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    4.97
  
  3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.39
  
  2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.50
  
  Speedo2 CPU    Enabled  10%   1.44/  1.76  20%   1.28/  1.92    1.59
  
  1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.49
  
  Description    State       Warning RPM  Current RPM
  
  -------------- ----------  -----------  -----------
  
  FAN 0     LEFT    Enabled         2160         3300
  
  FAN 1   CENTER    Enabled         2160         4105
  
  FAN 2    RIGHT    Enabled         2160         4155
  
  FAN 3       PS    Enabled         2160         3116
  
  FAN 4      PS'    Enabled         2160         4429
  
  Advisory   Critical   Fault      Current
  
  Description    State       Temp       Temp       Temp       Temp
  
  -------------- ----------  ---------  ---------  ---------  ---------
  
  NODE 0            Enabled   40C/104F   46C/114F   49C/120F   21C/ 69F
  
  NODE 1            Enabled   40C/104F   46C/114F   49C/120F   19C/ 66F
  
  001c16:
  
  Environmental monitoring is enabled and running.
  
  Description    State       Warning Limits     Fault Limits       Current
  
  -------------- ----------  -----------------  -----------------  -------
  
  12V IO    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.19
  
  12V DIG    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.12
  
  5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    4.97
  
  3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.32
  
  5V aux    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    4.94
  
  3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.39
  
  2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.50
  
  Speedo2 CPU    Enabled  10%   1.44/  1.76  20%   1.28/  1.92    1.58
  
  1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.49
  
  Description    State       Warning RPM  Current RPM
  
  -------------- ----------  -----------  -----------
  
  FAN 0     LEFT    Enabled         2160         3960
  
  FAN 1   CENTER    Enabled         2160         4105
  
  FAN 2    RIGHT    Enabled         2160         4105
  
  FAN 3       PS    Enabled         2160         3146
  
  FAN 4      PS'    Enabled         2160         4488
  
  Advisory   Critical   Fault      Current
  
  Description    State       Temp       Temp       Temp       Temp
  
  -------------- ----------  ---------  ---------  ---------  ---------
  
  NODE 0            Enabled   40C/104F   46C/114F   49C/120F   20C/ 68F
  
  NODE 1            Enabled   40C/104F   46C/114F   49C/120F   20C/ 68F
  
  001c18:
  
  Environmental monitoring is enabled and running.
  
  Description    State       Warning Limits     Fault Limits       Current
  
  -------------- ----------  -----------------  -----------------  -------
  
  12V IO    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.12
  
  12V DIG    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.06
  
  5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    4.99
  
  3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.34
  
  5V aux    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    4.97
  
  3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.39
  
  2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.50
  
  Speedo2 CPU    Enabled  10%   1.44/  1.76  20%   1.28/  1.92    1.58
  
  1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.49
  
  Description    State       Warning RPM  Current RPM
  
  -------------- ----------  -----------  -----------
  
  FAN 0     LEFT    Enabled         2160         4055
  
  FAN 1   CENTER    Enabled         2160         4055
  
  FAN 2    RIGHT    Enabled         2160         4055
  
  FAN 3       PS    Enabled         2160         3175
  
  FAN 4      PS'    Enabled         2160         4488
  
  Advisory   Critical   Fault      Current
  
  Description    State       Temp       Temp       Temp       Temp
  
  -------------- ----------  ---------  ---------  ---------  ---------
  
  NODE 0            Enabled   40C/104F   46C/114F   49C/120F   20C/ 68F
  
  NODE 1            Enabled   40C/104F   46C/114F   49C/120F   20C/ 68F
  
  001r20:
  
  Environmental monitoring is enabled and running.
  
  Description    State       Warning Limits     Fault Limits       Current
  
  -------------- ----------  -----------------  -----------------  -------
  
  12V bias    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   11.75
  
  2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.51
  
  3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.29
  
  5V aux    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    4.97
  
  Description    State       Warning RPM  Current RPM
  
  -------------- ----------  -----------  -----------
  
  FAN 0     LEFT    Enabled         2160         5024
  
  FAN 1    RIGHT    Enabled         2160         5429
  
  Advisory   Critical   Fault      Current
  
  Description    State       Temp       Temp       Temp       Temp
  
  -------------- ----------  ---------  ---------  ---------  ---------
  
  POWER             Enabled   30C/ 86F   35C/ 95F   40C/104F   21C/ 69F
  
  001c22:
  
  Environmental monitoring is enabled and running.
  
  Description    State       Warning Limits     Fault Limits       Current
  
  -------------- ----------  -----------------  -----------------  -------
  
  12V IO    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.12
  
  12V DIG    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.12
  
  5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    4.99
  
  3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.34
  
  5V aux    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    4.94
  
  3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.41
  
  2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.50
  
  Speedo2 CPU    Enabled  10%   1.44/  1.76  20%   1.28/  1.92    1.58
  
  1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.49
  
  Description    State       Warning RPM  Current RPM
  
  -------------- ----------  -----------  -----------
  
  FAN 0     LEFT    Enabled         2160         4007
  
  FAN 1   CENTER    Enabled         2160         4155
  
  FAN 2    RIGHT    Enabled         2160         4155
  
  FAN 3       PS    Enabled         2160         3116
  
  FAN 4      PS'    Enabled         2160         4488
  
  Advisory   Critical   Fault      Current
  
  Description    State       Temp       Temp       Temp       Temp
  
  -------------- ----------  ---------  ---------  ---------  ---------
  
  NODE 0            Enabled   40C/104F   46C/114F   49C/120F   22C/ 71F
  
  NODE 1            Enabled   40C/104F   46C/114F   49C/120F   21C/ 69F
  
  001c24:
  
  Environmental monitoring is enabled and running.
  
  Description    State       Warning Limits     Fault Limits       Current
  
  -------------- ----------  -----------------  -----------------  -------
  
  12V IO    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.25
  
  12V DIG    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.12
  
  5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    4.99
  
  3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.34
  
  5V aux    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    4.91
  
  3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.25
  
  2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.50
  
  Speedo2 CPU    Enabled  10%   1.44/  1.76  20%   1.28/  1.92    1.58
  
  1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.49
  
  Description    State       Warning RPM  Current RPM
  
  -------------- ----------  -----------  -----------
  
  FAN 0     LEFT    Enabled         2160         4055
  
  FAN 1   CENTER    Enabled         2160         4155
  
  FAN 2    RIGHT    Enabled         2160         4105
  
  FAN 3       PS    Enabled         2160         3175
  
  FAN 4      PS'    Enabled         2160         4488
  
  Advisory   Critical   Fault      Current
  
  Description    State       Temp       Temp       Temp       Temp
  
  -------------- ----------  ---------  ---------  ---------  ---------
  
  NODE 0            Enabled   40C/104F   46C/114F   49C/120F   22C/ 71F
  
  NODE 1            Enabled   40C/104F   46C/114F   49C/120F   21C/ 69F

I'm a bit confused to see that the fans seem to operate about 2x the Warning RPM.
Well, it is kind of noisy. Is there a "low-fan" parameter to set somewhere?

Code:

  M2100545-001-L2>pci
  
  001c12:
  
  Slot    Power
  
  ----    -----
  
  Slot 1  0.0
  
  Slot 2  15.0
  
  001c14:
  
  Slot    Power
  
  ----    -----
  
  Slot 1  0.0
  
  Slot 2  15.0
  
  001c16:
  
  Slot    Power
  
  ----    -----
  
  Slot 1  0.0
  
  Slot 2  15.0
  
  001c18:
  
  Slot    Power
  
  ----    -----
  
  Slot 1  0.0
  
  Slot 2  0.0
  
  001r20:
  
  INFO: command not supported on this brick type
  
  001c22:
  
  Slot    Power
  
  ----    -----
  
  Slot 1  0.0
  
  Slot 2  0.0
  
  001c24:
  
  Slot    Power
  
  ----    -----
  
  Slot 1  15.0
  
  Slot 2  0.0

So far so good. Back to finding a O350 to gfx-mod (close to Sweden...)

SGI: hinv

Origin 300. 24xR14000 600MHz. 22GB. Onyx4 skins