SGI: hinv

Octane2 / 2x400 / 5GB RAM / V8 / 36GB HDD

Geoman avatar
Geoman
Addict
Who joined May 26, 2005, 3:37 a.m.
and authored 367 notes
Wrote the following at March 24, 2007, 5:33 p.m...
I couldn't resist in upgrading my lovely toy:

Code:
Octane2 1% hinv -mv
Location: /hw/node
PM20400MHZ Board: barcode KYA069     part 030-1476-001 rev  D
Location: /hw/node/xtalk/15
IP30 Board: barcode MMP229     part 030-1467-001 rev  H
Location: /hw/node/xtalk/15/pci/2
PWR.SPPLY.ER Board: barcode AAE9200234 part 060-0035-002 rev  A
FP1 Board: barcode MCD790     part 030-0891-003 rev  H
Location: /hw/node/xtalk/11
ODY128 Board: barcode KTW991     part 030-1404-003 rev  A
2 400 MHZ IP30 Processors
Heart ASIC: Revision F
CPU: MIPS R12000 Processor Chip Revision: 3.5
FPU: MIPS R12010 Floating Point Chip Revision: 0.0
Main memory size: 5120 Mbytes
Xbow ASIC: Revision 1.4
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 2 Mbytes
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
Disk drive: unit 2 on SCSI controller 0 (unit 2)
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V8
Integral Fast Ethernet: ef0, version 1, pci 2
Iris Audio Processor: version RAD revision 12.0, number 1
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 3

Code:
Octane2 2% /usr/gfx/gfxinfo
Graphics board 0 is "ODYSSEY" graphics.
Managed (":0.0") 1280x1024
BUZZ version A.1
PB&J version 1
128MB memory
Banks: 4, CAS latency: 3
Monitor 0 type: Unknown
Channel 0:
Origin = (0,0)
Video Output: 1280 pixels, 1024 lines, 50.00Hz (1280x1024_50)

Running the V8 only at 50Hz on a F180 tft results in a clear image without the typical V6/V8 'OpenGL-artefacts' and problems.

_________________
:Octane2: 2xR12000 400MHz, 4GB RAM, V12 GFX
SGI - the legend will never die!!
Geoman avatar
Geoman
Addict
Who joined May 26, 2005, 3:37 a.m.
and authored 367 notes
Wrote the following at May 28, 2009, 1:59 a.m...
Code:
Octane2 4% hinv -mv
Location: /hw/node
PM20400MHZ Board: barcode KYA069     part 030-1476-001 rev  D
Location: /hw/node/xtalk/15
IP30 Board: barcode MMP229     part 030-1467-001 rev  H
Location: /hw/node/xtalk/15/pci/2
PWR.SPPLY.ER Board: barcode AAE1050838 part 060-0035-002 rev  A
FP1 Board: barcode MCD790     part 030-0891-003 rev  H
Location: /hw/node/xtalk/11
ODY128VERSIONB Board: barcode MDF774     part 030-1611-001 rev  C
2 400 MHZ IP30 Processors
Heart ASIC: Revision F
CPU: MIPS R12000 Processor Chip Revision: 3.5
FPU: MIPS R12010 Floating Point Chip Revision: 0.0
Main memory size: 8192 Mbytes
Xbow ASIC: Revision 1.4
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 2 Mbytes
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
Disk drive: unit 1 on SCSI controller 0 (unit 1)
Disk drive: unit 2 on SCSI controller 0 (unit 2)
Disk drive: unit 3 on SCSI controller 0 (unit 3)
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V12
Integral Fast Ethernet: ef0, version 1, pci 2
Iris Audio Processor: version RAD revision 12.0, number 1
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 3


Code:
Octane2 5% /usr/gfx/gfxinfo
Graphics board 0 is "ODYSSEY" graphics.
Managed (":0.0") 1696x1056
BUZZ version B.1
PB&J version 1
128MB memory
Banks: 4, CAS latency: 3
Monitor 0 type: Unknown
Channel 0:
Origin = (0,0)
Video Output: 1680 pixels, 1050 lines, 60.00Hz (1680x1050_60)

_________________
:Octane2: 2xR12000 400MHz, 4GB RAM, V12 GFX
SGI - the legend will never die!!
ninboy
Stranger
Who joined March 5, 2009, 7:34 p.m.
and authored 20 notes
Wrote the following at May 28, 2009, 6:49 p.m...
Never Posted the outpout for my O2. Here it is after some recent hardware changes
Code:
bash$  hinv -vm
CPU: MIPS R10000 Processor Chip Revision: 3.4
FPU: MIPS R10010 Floating Point Chip Revision: 0.0
1 250 MHZ IP32 Processor
Main memory size: 256 Mbytes
Secondary unified instruction/data cache size: 1 Mbyte on Processor 0
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
FLASH PROM version 4.18
Integral SCSI controller 0: Version ADAPTEC 7880
Disk drive: unit 2 on SCSI controller 0 (unit 2)
CDROM: unit 4 on SCSI controller 0
Integral SCSI controller 1: Version ADAPTEC 7880
Integral SCSI controller 2: Version IEEE1394 SBP2
On-board serial ports: tty1
On-board serial ports: tty2
On-board EPP/ECP parallel port
CRM graphics installed
Integral Ethernet: ec0, version 1
Iris Audio Processor: version A3 revision 1
PCI Adapter ID (vendor 0x9004, device 0x8078) PCI slot 1
PCI Adapter ID (vendor 0x9004, device 0x8078) PCI slot 2
PCI Adapter ID (vendor 0x104c, device 0x8024) PCI slot 3
Video: MVP unit 0 version 1.4
AV: AV1 Card version 1, Camera not connected.
Vice: TRE
DMediaPro DM10 FW option: unit 0, revision 1.1.0


bash$ /usr/gfx/gfxinfo -v
Graphics board 0 is "CRM" graphics.
Managed (":0.0") 1024x768
32 bitplanes
board revision 2, CRM revision C, GBE revision B
Monitor 0 type: AMT 13617
Channel 0:
Origin = (0,0)
Video Output: 1024 pixels, 768 lines, 75.03Hz (1024x768_75)
Video Format Flags:  (none)
Sync Disabled
Using Gamma Map 0

IRIS 1# configmon -h
SEQ            NAME      LOCATION          SERIAL_NUM   PART_NUMBER  REVISION
===============================================================================
0              NA            NA                  NA            NA        NA
1     MOTHERBOARD            NA                  NA            NA        NA
2  MAIN_MEMORY_256MB            NA                  NA            NA        NA
3          R10000            NA                  NA            NA        NA
4     SCSI_CTLR_0            NA                  NA            NA        NA
5         DRIVE_2            NA            3KT0GZRX    ST373207LC      0003
6         CDROM_4            NA                  NA            NA        NA
7     SCSI_CTLR_1            NA                  NA            NA        NA
8     SCSI_CTLR_2            NA                  NA            NA        NA
===============================================================================

IRIS 2# scsicontrol -i /dev/scsi/sc*
/dev/scsi/sc0d2l0:  Disk          SEAGATE ST373207LC      0003
ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing
Device is  ready
/dev/scsi/sc0d4l0:  CD-ROM        TOSHIBA CD-ROM XM-5401TA3605
ANSI vers 2, ISO ver: 0, ECMA ver: 0; supports:  reladdr synch linkedcmds
Device is  ready

_________________
:O2: R10K/256/73GB :Octane2: R12K/2GB/V6 dead :(
henrycault avatar
henrycault
Big Fan
Who joined Dec. 9, 2008, 11:30 a.m.
and authored 114 notes
Wrote the following at July 29, 2009, 5:42 p.m...
Here's my hinv output, Thanks a lot for the help i got from this board, and all previous posts, i did manage to make it work. At least on 7 of it's cpus.

Code:
Location: /hw/module/1/slot/n1/node
MODULEID Board: barcode K0017640   part              rev
IP31 Board: barcode HXN157     part 030-1255-003 rev  D
IP31PIMM Board: barcode HXR161     part 030-1313-002 rev  A
8P12_MPLN Board: barcode HXD826     part 030-0762-006 rev  K
Location: /hw/module/1/slot/n2/node
IP31 Board: barcode HTK556     part 030-1255-003 rev  B
IP31PIMM Board: barcode HTV192     part 030-1313-002 rev  A
Location: /hw/module/1/slot/n3/node
IP31 Board: barcode HXH456     part 030-1255-003 rev  D
IP31PIMM Board: barcode HXF394     part 030-1313-002 rev  A
Location: /hw/module/1/slot/n4/node
IP31 Board: barcode HXN148     part 030-1255-003 rev  D
IP31PIMM Board: barcode HXG351     part 030-1313-002 rev  A
Location: /hw/module/1/slot/r1/router
ROUTER_IR1 Board: barcode HRM549     part 030-0841-003 rev  B
Location: /hw/module/1/slot/r2/router
ROUTER_IR1 Board: barcode HAP382     part 030-0841-003 rev  B
Location: /hw/module/1/slot/io4/xtalk_pci
XTALK_PCI Board: barcode HXF987     part 030-1275-002 rev  B
Location: /hw/module/1/slot/io7/mscsi
MSCSI Board: barcode HMH301     part 030-1243-001 rev  M
Location: /hw/module/1/slot/io1/baseio
BASEIO Board: barcode HLR950     part 030-1124-002 rev  M
7 250 MHZ IP27 Processors
CPU: MIPS R10000 Processor Chip Revision: 3.4
FPU: MIPS R10010 Floating Point Chip Revision: 3.4
CPU 0 at Module 1/Slot 1/Slice A: 250 Mhz MIPS R10000 Processor Chip (enabled)
Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
CPU 1 at Module 1/Slot 1/Slice B: 250 Mhz MIPS R10000 Processor Chip (enabled)
Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
CPU 2 at Module 1/Slot 2/Slice A: 250 Mhz MIPS R10000 Processor Chip (enabled)
Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
CPU 7 at Module 1/Slot 2/Slice B: 250 Mhz MIPS R10000 Processor Chip (disabled)

Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
CPU 3 at Module 1/Slot 3/Slice A: 250 Mhz MIPS R10000 Processor Chip (enabled)
Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
CPU 4 at Module 1/Slot 3/Slice B: 250 Mhz MIPS R10000 Processor Chip (enabled)
Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
CPU 5 at Module 1/Slot 4/Slice A: 250 Mhz MIPS R10000 Processor Chip (enabled)
Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
CPU 6 at Module 1/Slot 4/Slice B: 250 Mhz MIPS R10000 Processor Chip (enabled)
Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
Main memory size: 4096 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 4 Mbytes
Memory at Module 1/Slot 1: 1024 MB (enabled)
Bank 0 contains 512 MB (Standard) DIMMS (enabled)
Bank 1 contains 512 MB (Standard) DIMMS (enabled)
Memory at Module 1/Slot 2: 1024 MB (enabled)
Bank 0 contains 512 MB (Standard) DIMMS (enabled)
Bank 1 contains 512 MB (Standard) DIMMS (enabled)
Memory at Module 1/Slot 3: 1024 MB (enabled)
Bank 0 contains 512 MB (Standard) DIMMS (enabled)
Bank 1 contains 512 MB (Standard) DIMMS (enabled)
Memory at Module 1/Slot 4: 1024 MB (enabled)
Bank 0 contains 512 MB (Standard) DIMMS (enabled)
Bank 1 contains 512 MB (Standard) DIMMS (enabled)
ROUTER in Module 1/Slot 2: Revision 2: Active Ports [4,5,6] (enabled)
ROUTER in Module 1/Slot 4: Revision 2: Active Ports [4,5,6] (enabled)
Integral SCSI controller 2: Version QL1040B (rev. 2), differential
Integral SCSI controller 3: Version QL1040B (rev. 2), differential
Integral SCSI controller 4: Version QL1040B (rev. 2), differential
Integral SCSI controller 5: Version QL1040B (rev. 2), differential
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
Disk drive: unit 1 on SCSI controller 0 (unit 1)
CDROM: unit 6 on SCSI controller 0
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
Integral Fast Ethernet: ef0, version 1, module 1, slot io1, pci 2
PCI Adapter ID (vendor 0x1112, device 0x2200) PCI slot 1
Origin MSCSI board, module 1 slot 7: Revision 4
Origin BASEIO board, module 1 slot 1: Revision 4
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 2
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 3
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
IOC3/IOC4 external interrupts: 1
HUB in Module 1/Slot 1: Revision 5 Speed 100.00 Mhz (enabled)
HUB in Module 1/Slot 2: Revision 5 Speed 100.00 Mhz (enabled)
HUB in Module 1/Slot 3: Revision 5 Speed 100.00 Mhz (enabled)
HUB in Module 1/Slot 4: Revision 5 Speed 100.00 Mhz (enabled)
IP27prom in Module 1/Slot n1: Revision 6.156
IP27prom in Module 1/Slot n2: Revision 6.156
IP27prom in Module 1/Slot n3: Revision 6.156
IP27prom in Module 1/Slot n4: Revision 6.156
IO6prom on Global Master Baseio in Module 1/Slot io1: Revision 6.156

_________________
:Octane: 270Mhz SI 384Mb ram :Octane2: 2x360Mhz V6+SE 1.5Gb ram
:O200: @ 225Mhz :O2000: 8x250Mhz 4Gb ram + MXE + IO6G
Image
Geoman avatar
Geoman
Addict
Who joined May 26, 2005, 3:37 a.m.
and authored 367 notes
Wrote the following at Aug. 19, 2009, 7:53 a.m...
I see that a lot of users are using big and fast hard-drives in their O2s. So the O2 is capable of cooling them sufficiently at last. (which I did not expect)

_________________
:Octane2: 2xR12000 400MHz, 4GB RAM, V12 GFX
SGI - the legend will never die!!
Geoman avatar
Geoman
Addict
Who joined May 26, 2005, 3:37 a.m.
and authored 367 notes
Wrote the following at Aug. 20, 2009, 3:56 a.m...
2 Memory modules died :-(

_________________
:Octane2: 2xR12000 400MHz, 4GB RAM, V12 GFX
SGI - the legend will never die!!
bigD avatar
bigD
Addict
Who joined June 17, 2008, 8:38 p.m.
and authored 317 notes
Wrote the following at Aug. 20, 2009, 2:55 p.m...
Sorry to hear about your RAM, Geoman. I had some Dataram memory that served me pretty well for about a year, and one module apparently died right as I sold four sticks of it. It could have been damaged in shipping though - but it does seem like people have been having issues with it. :(

_________________
:Onyx2: :Octane2: :Indigo2: :0300:
Onyx2, 4x400 MHz, IR3 // Origin 300, 4x600MHz
Octane2, 2x400 MHz, V12 // Indigo2, 200 MHz, Extreme
Geoman avatar
Geoman
Addict
Who joined May 26, 2005, 3:37 a.m.
and authored 367 notes
Wrote the following at Aug. 21, 2009, 3:26 a.m...
Yes, the modules from Kingston and SGI are the double stacked ones, which are comparatively robust.
The ICs on the DATARAM modules look like those for notebooks, they are soldered side by side via ball grid array.

Seems like they're indeed very delicate.

_________________
:Octane2: 2xR12000 400MHz, 4GB RAM, V12 GFX
SGI - the legend will never die!!
henrycault avatar
henrycault
Big Fan
Who joined Dec. 9, 2008, 11:30 a.m.
and authored 114 notes
Wrote the following at Aug. 30, 2009, 11:58 a.m...
Got some pics on its uber-technological wooden base. Will take more when i will mount it in a rack. It's also waiting for a MXE+IO6G hack, im still waiting after the IO6G. Oh and i should plug a KILL-A-WATT on it's outlet, im driving it from a standard 120V 15Amps socket, and the breaker never tripped yet. Im beggining to think that it would draw that humongous 2000 Watts only if it was totally full of XIO boards, and with a 100% cpu load. For now it looks more like a theoretical max current draw than a real thing, like if it had 8x500Mhz and maxed out ram and maxed out directory ram and so on.
Attachment:
O2k01.jpg
O2k01.jpg [ 503.5 KiB | Viewed 102 times ]
Attachment:
O2k02.jpg
O2k02.jpg [ 467.05 KiB | Viewed 102 times ]

^
|
Uber IBM Intellistation. lame x86 cpu.

_________________
:Octane: 270Mhz SI 384Mb ram :Octane2: 2x360Mhz V6+SE 1.5Gb ram
:O200: @ 225Mhz :O2000: 8x250Mhz 4Gb ram + MXE + IO6G
Image
Geoman avatar
Geoman
Donor
From Munich, Germany
Who joined May 26, 2005, 3:37 a.m.
Wrote the following at Oct. 24, 2014, 11:51 a.m...
So I modded the Shoehorn: I had to remove the 013-1926-002 C metal plate* and sawed away the spacer parts from the pcb that collided with the hexagonal screws at the top of the XIO-carrier + used the screws from the placeholder that was on the XIO-carrier. Fits perfectly now.

*not so easy...

Thanks to you fellow Nekochaners, I flasehd my 3C-996 to SGI-firmware:
http://forums.nekochan.net/viewtopic.php?f=3&t=12702&hilit=3c996&start=45#p7294465

So now I've got Gigabit Ethernet up and running at last!
:Octane2: 2xR12000 400MHz, 4GB RAM, V12
SGI - the legend will never die!!
hamei
From over the rainbow
Who joined Feb. 24, 2004, 4:10 p.m.
Wrote the following at Oct. 24, 2014, 8:16 p.m...
Geoman wrote: So now I've got Gigabit Ethernet up and running at last!

I see you've got it in D ... does that kick you into fastfan ?
"it was the second night of the Fuck Rally at Cal ..."
Geoman avatar
Geoman
Donor
From Munich, Germany
Who joined May 26, 2005, 3:37 a.m.
Wrote the following at Oct. 25, 2014, 1:16 a.m...
I installed it on the lower left port. - But the arrow clearly shows D. So fortunately no fastfan.

Strange indeed.
:Octane2: 2xR12000 400MHz, 4GB RAM, V12
SGI - the legend will never die!!