SGI: hinv

My ORIGIN200(2x225MHz)

mila avatar
mila
Who joined Dec. 31, 2009, 4:20 a.m.
and authored 281 notes
Wrote the following at Nov. 27, 2012, 3:02 p.m...
Code:
origin200 18# hinv -vm
Location: /hw/module/1/slot/MotherBoard/node
PIMM_225_2M_2P Board: barcode HTT463     part 013-2382-002 rev  B
Location: /hw/module/1/slot/MotherBoard/node/xtalk/8
IP29 Board: barcode HTZ237     part 030-1389-001 rev  A
Location: /hw/module/1/slot/MotherBoard/node/xtalk/8/pci/2
2 225 MHZ IP27 Processors
CPU: MIPS R10000 Processor Chip Revision: 3.4
FPU: MIPS R10010 Floating Point Chip Revision: 3.4
CPU 0 at Module 1/Slot 1/Slice A: 225 Mhz MIPS R10000 Processor Chip (enabled)
Processor revision: 3.4. Scache: Size 2 MB Speed 225 Mhz   Tap 0x9
CPU 1 at Module 1/Slot 1/Slice B: 225 Mhz MIPS R10000 Processor Chip (enabled)
Processor revision: 3.4. Scache: Size 2 MB Speed 225 Mhz   Tap 0x9
Main memory size: 2048 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 2 Mbytes
Memory at Module 1/Slot 1: 2048 MB (enabled)
Bank 0 contains 512 MB (Standard) DIMMS (enabled)
Bank 1 contains 512 MB (Standard) DIMMS (enabled)
Bank 2 contains 512 MB (Standard) DIMMS (enabled)
Bank 3 contains 512 MB (Standard) DIMMS (enabled)
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
Disk drive: unit 1 on SCSI controller 0 (unit 1)
Disk drive: unit 2 on SCSI controller 0 (unit 2)
Disk drive: unit 3 on SCSI controller 0 (unit 3)
Disk drive: unit 4 on SCSI controller 0 (unit 4)
Disk drive: unit 5 on SCSI controller 0 (unit 5)
Disk drive: unit 6 on SCSI controller 0 (unit 6)
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
CDROM: unit 6 on SCSI controller 1
IOC3 serial port: tty1
IOC3 serial port: tty2
IOC3 parallel port: plp1
Integral Fast Ethernet: ef0, version 1, module 1, slot MotherBoard, pci 2
Origin 200 base I/O, module 1 slot 1
PCI Adapter ID (vendor 4265, device 3) pci slot 2
PCI Adapter ID (vendor 4215, device 4128) pci slot 0
PCI Adapter ID (vendor 4215, device 4128) pci slot 1
IOC3 external interrupts: 1
HUB in Module 1/Slot 1: Revision 5 Speed 90.00 Mhz (enabled)
IP27prom in Module 1/Slot n1: Revision 6.64
origin200 19#
origin200 19# gfxinfo
gfxinfo: Command not found.
origin200 20# uname -aR
IRIX64 origin200 6.5 6.5.13m 07091542 IP27
origin200 21# /sbin/diskpatch -v
sc0d1l0:  Disk         SGI     IBM  DGHS09Y    0190  Serial: 6812DB04
sc0d2l0:  Disk         SGI     IBM DNES-309170YSAF0  Serial: AJ13Q096
sc0d3l0:  Disk         SGI     IBM DNES-309170YSAF0  Serial: AJHEV974
sc0d4l0:  Disk         SGI     IBM DNES-309170YSAF0  Serial: AJHF7700
sc0d5l0:  Disk         SEAGATE ST336704LSUN36G 032C  Serial: 3CD136XM
sc0d6l0:  Disk         SEAGATE ST336704LSUN36G 032C  Serial: 3CD137KE

_________________
--
No Microsoft product was used in any way to write or send this text.
If you use a Microsoft product to read it, you're doing so at your own
risk.
Pontus
Who joined May 8, 2008, 11:12 a.m.
and authored 493 notes
Wrote the following at Nov. 28, 2012, 11:28 p.m...
Nice, how are the skins?

_________________
:Onyx2R: :IRIS3130: :Onyx2: :O2000: :PI: :Fuel: :Indigo: :Octane: :O2: :Indigo2IMP: :Indigo2: :Indy: :1600SW: :pdp8e:
:BA213: <- MicroVAX 3500 :BA213: <- DECsystem 5500 :BA215: <- MicroVAX 3300
Pictures of my collection: www.pdp8.se
jan-jaap avatar
jan-jaap
Who joined June 17, 2004, 10:35 a.m.
and authored 3603 notes
Wrote the following at Nov. 29, 2012, 2:50 a.m...
Pontus wrote:
Nice, how are the skins?

What a cruel thing to ask :lol:

I'm using a similar system as my install server. Installed a TG gigabit card and an FDDI card, so network installations are always at maximum speed. It's got a QL2342 too so I could eventually move the installation media to a SAN. With these cards installed, PCI slot order is important. Otherwise the TG card complains about a lack of some sort of bufs at boot and drops the interface when under load.

The O200 makes for a decent (though loud!) server. If you want to do something similar I'll look up the PCI slot config of mine.

_________________
Now this is a deep dark secret, so everybody keep it quiet :)
It turns out that when reset, the WD33C93 defaults to a SCSI ID of 0, and it was simpler to leave it that way... -- Dave Olson, in comp.sys.sgi
Currently in commercial service: Image :Onyx2: (2x) :O3x02L:
In the museum : almost every MIPS/IRIX system.
Wanted : GM1 board for Professional Series GT graphics (030-0076-003, 030-0076-004)
Pontus
Who joined May 8, 2008, 11:12 a.m.
and authored 493 notes
Wrote the following at Nov. 29, 2012, 1:25 p.m...
jan-jaap wrote:
Pontus wrote:
Nice, how are the skins?

What a cruel thing to ask :lol:

I know.. I have one with decent skins, until my father picked it up during my recent move :/ I'm hoping to glue it back together.

_________________
:Onyx2R: :IRIS3130: :Onyx2: :O2000: :PI: :Fuel: :Indigo: :Octane: :O2: :Indigo2IMP: :Indigo2: :Indy: :1600SW: :pdp8e:
:BA213: <- MicroVAX 3500 :BA213: <- DECsystem 5500 :BA215: <- MicroVAX 3300
Pictures of my collection: www.pdp8.se