SGI: hinv

Origin 350: 16xR16K 700MHz, 4GB RAM

ramq
From Sweden
Who joined Jan. 25, 2008, 6:06 a.m.

Wrote the following at Dec. 12, 2009, 4:06 p.m...

May I present 'Venom', my newly downsized Origin 350 multi-brick config!
This is what's left at the moment from my rescent aquire and is trimmed down to a more manageable size (=less powerdraw).

Code: Select all


hinv -vm


Location: /hw/module/001c01/node


IP53_4CPU Board: barcode MXD727     part 030-1868-001 rev -C


Location: /hw/module/001c01/IXbrick/xtalk/15


2U_INT_53 Board: barcode MTZ152     part 030-1809-003 rev -B


Location: /hw/module/001c01/IXbrick/xtalk/15/pci-x/0/1/ioc4


IO9 Board: barcode MTS407     part 030-1771-005 rev -A


Location: /hw/module/001c02/node


IP53_4CPU Board: barcode MXM753     part 030-1868-001 rev -C


Location: /hw/module/001c02/IXbrick/xtalk/15


2U_INT_53 Board: barcode MTC260     part 030-1809-003 rev -A


Location: /hw/module/001c02/IXbrick/xtalk/15/pci-x/0/1/ioc4


IO9 Board: barcode MTS540     part 030-1771-005 rev -A


Location: /hw/module/001c03/node


IP53_4CPU Board: barcode MTA290     part 030-1868-001 rev -C


Location: /hw/module/001c03/IXbrick/xtalk/15


2U_INT_53 Board: barcode MTC253     part 030-1809-003 rev -A


Location: /hw/module/001c04/node


IP53_4CPU Board: barcode MTA291     part 030-1868-001 rev -C


Location: /hw/module/001c04/IXbrick/xtalk/15


2U_INT_53 Board: barcode MTV599     part 030-1809-003 rev -A


Location: /hw/module/001r05/router


ROUTER Board: barcode MVA352     part 030-1634-003 rev -A


16 700 MHZ IP35 Processors


CPU: MIPS R16000 Processor Chip Revision: 2.1


FPU: MIPS R16010 Floating Point Chip Revision: 2.1


CPU 0 at Module 001c01/Slot 0/Slice A: 700 Mhz MIPS R16000 Processor Chip (enabled)


Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc


CPU 1 at Module 001c01/Slot 0/Slice B: 700 Mhz MIPS R16000 Processor Chip (enabled)


Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc


CPU 2 at Module 001c01/Slot 0/Slice C: 700 Mhz MIPS R16000 Processor Chip (enabled)


Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc


CPU 3 at Module 001c01/Slot 0/Slice D: 700 Mhz MIPS R16000 Processor Chip (enabled)


Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc


CPU 4 at Module 001c02/Slot 0/Slice A: 700 Mhz MIPS R16000 Processor Chip (enabled)


Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc


CPU 5 at Module 001c02/Slot 0/Slice B: 700 Mhz MIPS R16000 Processor Chip (enabled)


Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc


CPU 6 at Module 001c02/Slot 0/Slice C: 700 Mhz MIPS R16000 Processor Chip (enabled)


Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc


CPU 7 at Module 001c02/Slot 0/Slice D: 700 Mhz MIPS R16000 Processor Chip (enabled)


Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc


CPU 8 at Module 001c03/Slot 0/Slice A: 700 Mhz MIPS R16000 Processor Chip (enabled)


Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc


CPU 9 at Module 001c03/Slot 0/Slice B: 700 Mhz MIPS R16000 Processor Chip (enabled)


Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc


CPU 10 at Module 001c03/Slot 0/Slice C: 700 Mhz MIPS R16000 Processor Chip (enabled)


Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc


CPU 11 at Module 001c03/Slot 0/Slice D: 700 Mhz MIPS R16000 Processor Chip (enabled)


Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc


CPU 12 at Module 001c04/Slot 0/Slice A: 700 Mhz MIPS R16000 Processor Chip (enabled)


Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc


CPU 13 at Module 001c04/Slot 0/Slice B: 700 Mhz MIPS R16000 Processor Chip (enabled)


Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc


CPU 14 at Module 001c04/Slot 0/Slice C: 700 Mhz MIPS R16000 Processor Chip (enabled)


Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc


CPU 15 at Module 001c04/Slot 0/Slice D: 700 Mhz MIPS R16000 Processor Chip (enabled)


Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc


Main memory size: 4096 Mbytes


Instruction cache size: 32 Kbytes


Data cache size: 32 Kbytes


Secondary unified instruction/data cache size: 4 Mbytes


Memory at Module 001c01/Slot 0: 1024 MB (enabled)


Bank 0 contains 512 MB (Premium) DIMMS (enabled)


Bank 1 contains 512 MB (Premium) DIMMS (enabled)


Memory at Module 001c02/Slot 0: 1024 MB (enabled)


Bank 0 contains 512 MB (Premium) DIMMS (enabled)


Bank 1 contains 512 MB (Premium) DIMMS (enabled)


Memory at Module 001c03/Slot 0: 1024 MB (enabled)


Bank 0 contains 512 MB (Premium) DIMMS (enabled)


Bank 1 contains 512 MB (Premium) DIMMS (enabled)


Memory at Module 001c04/Slot 0: 1024 MB (enabled)


Bank 0 contains 512 MB (Premium) DIMMS (enabled)


Bank 1 contains 512 MB (Premium) DIMMS (enabled)


ROUTER in Module 001c01/Slot 0: Revision 1: Active Ports [2,3,4,5,] (enabled)


Integral SCSI controller 19: Version IDE (ATA/ATAPI) IOC4


Integral SCSI controller 2: Version IDE (ATA/ATAPI) IOC4


CDROM: unit 0 on SCSI controller 2


Integral SCSI controller 20: Version QL12160, low voltage differential


Integral SCSI controller 21: Version QL12160, low voltage differential


Integral SCSI controller 0: Version QL12160, low voltage differential


Disk drive: unit 1 on SCSI controller 0 (unit 1)


Integral SCSI controller 1: Version QL12160, low voltage differential


IOC3/IOC4 serial port: tty27


IOC3/IOC4 serial port: tty28


IOC3/IOC4 serial port: tty29


IOC3/IOC4 serial port: tty30


IOC3/IOC4 serial port: tty23


IOC3/IOC4 serial port: tty24


IOC3/IOC4 serial port: tty25


IOC3/IOC4 serial port: tty26


Gigabit Ethernet: tg6, module 001c02, PCI bus 1 slot 4


Integral Gigabit Ethernet: tg0, module 001c01, PCI bus 1 slot 4


PCI Adapter ID (vendor 0x10a9, device 0x100a) PCI slot 1


PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 3


PCI Adapter ID (vendor 0x14e4, device 0x1645) PCI slot 4


PCI Adapter ID (vendor 0x10a9, device 0x100a) PCI slot 1


PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 3


PCI Adapter ID (vendor 0x14e4, device 0x1645) PCI slot 4


IOC4 firmware revision 79


IOC4 firmware revision 79


IOC3/IOC4 external interrupts: 6


IOC3/IOC4 external interrupts: 1


HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)


HUB in Module 001c02/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)


HUB in Module 001c03/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)


HUB in Module 001c04/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)


IP35prom in Module 001c01/Slot n0: Revision 6.210


IP35prom in Module 001c02/Slot n0: Revision 6.210


IP35prom in Module 001c03/Slot n0: Revision 6.210


IP35prom in Module 001c04/Slot n0: Revision 6.210

Code: Select all


l1cmd serial all




Data                            Location      Value


------------------------------  ------------  --------


Local System Serial Number      NVRAM         M2100629


Reference System Serial Number  NVRAM         M2100629


Local Brick Serial Number       EEPROM        MTZ152


Reference Brick Serial Number   NVRAM         MTZ152






EEPROM      Product Name    Serial      Part Number           Rev  T/W


----------  --------------  ----------  --------------------  ---  ------


INTERFACE   2U_INT_53       MTZ152      030_1809_003          B    00


IO9         IO9             MTS407      030_1771_005          A    00


ODYSSEY     no hardware detected


RISER       2U_RISER        MXN357      030_1808_005          A    00


NODE        IP53_4CPU       MXD727      030_1868_001          C    00




EEPROM     JEDEC-SPD Info           Part Number        Rev Speed  SGI


---------- ------------------------ ------------------ --- ------ --------


DIMM 0     CE000000000000005FF40800 M3 46L6510BT1-CA0  0B   10.0  NO DATA


DIMM 2     no hardware detected


DIMM 4     no hardware detected


DIMM 6     no hardware detected


DIMM 1     CE000000000000005FC80C00 M3 46L6510BT1-CA0  0B   10.0  NO DATA


DIMM 3     no hardware detected


DIMM 5     no hardware detected


DIMM 7     no hardware detected

Code: Select all


l1cmd env


Environmental monitoring is enabled and running.




Description    State       Warning Limits     Fault Limits       Current


-------------- ----------  -----------------  -----------------  -------


12V   Disabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.06


12V    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.06


5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    4.97


3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.32


12V IO    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.06


5V aux    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.04


3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.27


5V aux    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.04


3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.32


2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.51


1.8V    Enabled  10%   1.62/  1.98  20%   1.44/  2.16    1.78


3.3V aux   Disabled  10%   2.97/  3.63  20%   2.64/  3.96    3.27


XIO 12V bias   Disabled  10%  10.80/ 13.20  20%   9.60/ 14.40    0.00


XIO 5V   Disabled  10%   4.50/  5.50  20%   4.00/  6.00    0.00


XIO 2.5V   Disabled  10%   2.25/  2.75  20%   2.00/  3.00    0.00


XIO 3.3V aux   Disabled  10%   2.97/  3.63  20%   2.64/  3.96    0.00


NODE0 3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.27


NODE0 5V aux    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.04


NODE0 12V    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.00


NODE0 SRAM    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.50


NODE0 1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.49


NODE0 CPU    Enabled  10%   1.13/  1.38  20%   1.00/  1.50    1.25




Description    State       Warning RPM  Current RPM


-------------- ----------  -----------  -----------


FAN 0  EXHST 1    Enabled         2160         2305


FAN 1  EXHST 2    Enabled         2160         2305


FAN 2       PS    Enabled         1575         1980


FAN 3    PCI 1    Enabled         2160         2589


FAN 4    PCI 2    Enabled         2160         2877




Advisory   Critical   Fault      Current


Description    State       Temp       Temp       Temp       Temp


-------------- ----------  ---------  ---------  ---------  ---------


INTERFACE 0       Enabled   31C/ 87F   48C/118F   55C/131F    5C/ 41F -23-


INTERFACE 1       Enabled   31C/ 87F   48C/118F   55C/131F    6C/ 42F -23-


INTERFACE 2       Enabled   31C/ 87F   48C/118F   55C/131F   11C/ 51F -13-


PCI RISER         Enabled   31C/ 87F   48C/118F   55C/131F   10C/ 50F -11-


ODYSSEY          Disabled


NODE              Enabled   31C/ 87F   48C/118F   55C/131F    8C/ 46F -14-


BEDROCK           Enabled   31C/ 87F   48C/118F   55C/131F    3C/ 37F -31-

Code: Select all


scsicontrol -i /dev/scsi/sc*


/dev/scsi/sc0d1l0:  Disk          COMPAQ  BD1468A4B5      HPB8


ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing


Device is  ready


/dev/scsi/sc2d0l0:  CD-ROM        MATSHITADVD-ROM SR-8178 PZ21


ANSI vers 0, ISO ver: 0, ECMA ver: 0; supports:


Device is  not ready

Code: Select all


/sbin/diskpatch -v


sc0d1l0:  Disk         COMPAQ  BD1468A4B5      HPB8  Serial: J405XJ1K

recondas
Moderator
From NC - USA
Who joined June 6, 2004, 5:55 p.m.

Wrote the following at Dec. 12, 2009, 6 p.m...

Very nice! Any plans to add graphics?

BTW, were you able to use the pin-out information to set up a power supply for your L2 controller? Like you, I have two systems with L2 controllers, and have I've found the L3 software to be very handy as an overall controller/remote monitoring tool for both systems. I run it on the same lightweight system used as a Synergy host <run so I can share a single keyboard and mouse between the Onyx 300, Onyx 350, a PC and a Mac>.

***********************************************************************
Welcome to ARMLand - 0/0x0d00
running...(sherwood-root 0607201829)
* InfiniteReality/Reality Software, IRIX 6.5 Release *
***********************************************************************

hamei
From over the rainbow
Who joined Feb. 24, 2004, 4:10 p.m.

Wrote the following at Dec. 13, 2009, 12:02 a.m...

recondas wrote: < so I can share a single keyboard and mouse between the Onyx 300, Onyx 350, a PC and a Mac >.

I hate to say this, but have you guys considered the possibility that maybe you're getting a little carried away ? :shock:

guardian452
Donor
From Kentucky, United States
Who joined Aug. 21, 2007, 10:12 p.m.

Wrote the following at Dec. 13, 2009, 11:41 a.m...

well, good keyboards and mice ARE hard to find

Google: Don't Be Evil. Apple: Don't Be Greedy. Microsoft: Don't Be Stupid.

foetz
Moderator
Who joined April 14, 2003, 4:34 a.m.

Wrote the following at Dec. 13, 2009, 10:35 p.m...

sybrfreq wrote: well, good keyboards and mice ARE hard to find

indeed. i'm always stocking up granite kb and mice as good as i can

r-a-c.de

ramq
From Sweden
Who joined Jan. 25, 2008, 6:06 a.m.

Wrote the following at Dec. 14, 2009, 2:19 a.m...

recondas wrote: Very nice! Any plans to add graphics?

Well, yes and no. I'm planning on incorporating the famous "V10 hack", but it's on very low priority cause I currently don't need graphics on it, other than for fun. A little FW-card and USB will probably pimp this machine a little further, but nothing planned further than that.
Well, apart from memory that is. (Currently I have some 2GB kits in hopefully a couple of weeks.)

BTW, were you able to use the pin-out information to set up a power supply for your L2 controller? Like you, I have two systems with L2 controllers, and have I've found the L3 software to be very handy as an overall controller/remote monitoring tool for both systems.

Well, actually I haven't had time for it yet. Had some spare time this weekend to fire up this thing, plus diagnosing other bricks, etc. I'll probably measure the pinout next time I'll dedicate time for the O3800 system + power measuring.
So far this hasn't been a problem though, since the L3 software takes care of all my needs so far. Only drawback is that L1-reconfigs (changing rack/slot numbers + associated reboot) crap things up on the little Linux-bugger, so I have to reboot it every time I make such changes.