The collected works of Mojo

Mojo
Who joined July 17, 2012, 4:12 a.m.
and authored 3 notes
Wrote on the subject of Irix Text Editor (GUI) at March 15, 2013, 6:21 a.m...
hi

Anyone know of text editor like Programmers Notepad that will complie/run on IRIX. I've used the usual command line editors and nedit, however i'm looking for somthing a little more modern.

Regards
Mojo
Who joined July 17, 2012, 4:12 a.m.
and authored 3 notes
Wrote on the subject of Dead fuel at April 15, 2013, 8:45 a.m...
hi

hoping anyone could help? my fuel has stopped booting and shows me a red and white flashing light.

I have connected to the serial port and i get the following output

    IP35 PROM SGI Version 6.210 built 02:33:51 PM Aug 26, 2004
    Running in DDR mode
    Testing/Initializing memory ............... DONE
    Copying PROM code to memory ............... DONE
    Discovering local IO ...................... WARNING: xbow_base: 0x92
    00000000000000 link: 13 Widget present, but link not alive!
    WARNING: xbow_base: 0x9200000000000000 link: 13 Widget present, but link not ali
    ve!
    DONE
    Discovering NUMAlink connectivity .........
    Local hub NUMAlink is down.
    *** Local network link down
    DONE
    Found 1 objects (1 hubs, 0 routers) in 30362 usec
    Waiting for peers to complete discovery.... DONE
    No other nodes present; becoming global master
    Global master is /hw/rack/001/bay/01
    Intializing any CPUless nodes.............. DONE
    Checking partitioning information ......... DONE
    No other nodes present; becoming partition master
    Loading BASEIO prom ....................... DONE

    BASEIO PROM Monitor SGI Version 6.210 built 02:30:38 PM Aug 26, 2004 (BE64)
    1 CPUs on 1 nodes found.
    Automatic update of PROM environment disabled

    PS/2 Keyboard & Mouse diagnostics
    Found mouse on port 0
    Found keyboard on port 1
    LEDs test: keyboard doesn't answer
    pckm failed:
    RSLT pckm FAIL diag_rc = 73

    Failed pckm diagnostics

    Graphics diagnostics

    Installing PROM Device drivers ............
    Base I/O Ethernet set to /dev/ethernet/ef0
    Installing Graphics Console...
    graphics install: searching for pipe 0
    klgraphics: System has no GFX

    Walking SCSI Adapter 0, (pci id 1)
    1+ Device Vendor Product: SGI ST373405LW
    2- 3- 4- 5- 6- 7- 8- 9- 10- 11- 12- 13- 14- 15- = 1 device(s)


    Walking SCSI Adapter 1, (pci id 1)
    1- 2- 3- 4- 5- 6- 7- 8- 9- 10- 11- 12- 13- 14- 15- = 0 device(s)

    Initializing PROM Device drivers .......... DONE
    Cannot open /dev/graphics/textport for output
    Cannot open /dev/graphics/textport for output
    Checking hardware inventory ............... ***Warning: Found a new
    New Type board in module 001c01, serial
    Please use the 'update' command from the PROM Monitor to update the inventory
    DONE

    **** System Configuration and Diagnostics Summary ****
    CONFIG:
    No. of NODEs enabled = 1
    No. of NODEs disabled = 0
    No. of CPUs enabled = 1
    No. of CPUs disabled = 0
    Mem enabled = 2048 MB
    Mem disabled = 0 MB
    No. of RTRs enabled = 0
    No. of RTRs disabled = 0

    DIAG RESULTS:
    /hw/module/001c01/brick/xtalk/13: IO link bad
    **** End System Configuration and Diagnostics Summary ****


    System Maintenance Menu

    1) Start System
    2) Install System Software
    3) Run Diagnostics
    4) Recover System
    5) Enter Command Monitor

I can boot the system using option 1, thats all i've done.

Any help would be greatly greatly appreciated.

Regards