This is the Octane that uunix spotted on Ebay but could not collect, so I picked it up. Since then he seems to have found others to distract him ... so here's the hinv. I had been pessimistic as the model number suggested only a 175MHz machine, but it turned out to have been used within SGI until around 2006 and had been upgraded.
Bit of a mixture - Xbow 1.4 and a newer m/b but Lucent PSU. The SCSI drives are two IBM 9GB units, now one a clone of the other with 128MB swap (the fx default) and the rest as a root partition. I think there should be TRAM showing for the SE board, it's there but maybe u/s - like the second processor, which PROM hinv reports but is disabled in IRIX. I have tried removing the PM to reseat it, but one stand-off seems stuck; the bolt can be loosened but the PM won't lift at that point (halfway along the side nearest the edge of the m/b). Dual-screen is nice; the "assumed 19" monitors" are a 17" CRT and a 22" LCD-TV! Pretty sure it had a CADduo card in a PCI cage at SGI but xinerama is doing the trick with a single keybd+mouse input. It does seem to "stall" at intervals, so perhaps some SGI-office-network config that needs to be cleaned out? Most services chkconfig'd off. Skins in good condition, as is one drive sled (the seller broke the other while pulling it out to show me the drive
).
Code: Select all
Location: /hw/node
Part:030-1286-002;Name:PM20250MHZ;Serial:GTJ939;Revision:B;Group:ff;Capability:ffffffff;Variety:ff;Laser:000000246615;
Location: /hw/node/xtalk/15
Part:030-1467-001;Name:IP30;Serial:MEW365;Revision:D;Group:ff;Capability:ffffffff;Variety:ff;Laser:00000059d294;
Location: /hw/node/xtalk/15/pci/2
Part:060-0038-001;Name:PWR.SPPLY.S2;Serial:AAC8150074;Revision:C;Group:ff;Capability:ffffffff;Variety:ff;Laser:00000021fe8d;
Part:030-0891-003;Name:FP1;Serial:98829B;Revision:F;Group:ff;Capability:ffffffff;Variety:ff;Laser:0000001a23bd;
Location: /hw/node/xtalk/12
Part:030-1240-003;Name:MOT20;Serial:KXX073;Revision:H;Group:ff;Capability:ffffffff;Variety:ff;Laser:00000049c163;
Part:030-1196-002;Name:MCO;Serial:GBG509;Revision:C;Group:ff;Capability:ffffffff;Variety:ff;Laser:0000001a301f;
Location: /hw/node/xtalk/9
Part:030-0938-003;Name:GM10;Serial:ENJ563;Revision:T;Group:ff;Capability:ffffffff;Variety:ff;Laser:000000183180;
1 250 MHZ IP30 Processor
Heart ASIC: Revision F
CPU: MIPS R10000 Processor Chip Revision: 3.4
FPU: MIPS R10010 Floating Point Chip Revision: 0.0
Main memory size: 1152 Mbytes
Xbow ASIC: Revision 1.4
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 1 Mbyte
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
Disk drive: unit 1 on SCSI controller 0 (unit 1)
Disk drive: unit 2 on SCSI controller 0 (unit 2)
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: EMXI
Graphics board: SI
Integral Fast Ethernet: ef0, version 1, pci 2
Iris Audio Processor: version RAD revision 12.0, number 1
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 3
OCTANE Channel Option Board
Code: Select all
Graphics board 0 is "IMPACTSR" graphics.
Managed (":0.0") 1280x1024
Product ID 0x3, 2 GEs, 2 REs, 4 TRAMs
MGRAS revision 4, RA revision 0
HQ rev B, GE12 rev A, RE4 rev C, PP1 rev H,
VC3 rev A, CMAP rev F, Heart rev F
unknown, assuming 19" monitor (id 0xf)
OCO board present (rev 2)
Channel 0:
Origin = (0,0)
Video Output: 1280 pixels, 1024 lines, 60.00Hz (1280x1024_60)
Graphics board 1 is "IMPACTSR" graphics.
Managed (":0.1") 1280x1024
Product ID 0x2, 1 GE, 1 RE, 0 TRAMs
MGRAS revision 1, RA revision 0
HQ rev B, GE11 rev B, RE4 rev C, PP1 rev A,
VC3 rev A, CMAP rev E, Heart rev F
unknown, assuming 19" monitor (id 0xf)
Channel 0:
Origin = (0,0)
Video Output: 1280 pixels, 1024 lines, 60.00Hz (1280x1024_60)
Bit of a mixture - Xbow 1.4 and a newer m/b but Lucent PSU. The SCSI drives are two IBM 9GB units, now one a clone of the other with 128MB swap (the fx default) and the rest as a root partition. I think there should be TRAM showing for the SE board, it's there but maybe u/s - like the second processor, which PROM hinv reports but is disabled in IRIX. I have tried removing the PM to reseat it, but one stand-off seems stuck; the bolt can be loosened but the PM won't lift at that point (halfway along the side nearest the edge of the m/b). Dual-screen is nice; the "assumed 19" monitors" are a 17" CRT and a 22" LCD-TV! Pretty sure it had a CADduo card in a PCI cage at SGI but xinerama is doing the trick with a single keybd+mouse input. It does seem to "stall" at intervals, so perhaps some SGI-office-network config that needs to be cleaned out? Most services chkconfig'd off. Skins in good condition, as is one drive sled (the seller broke the other while pulling it out to show me the drive
).
