Nekonomicon - Fuel R14000 500MHz, 1GB

agkbill
From Sweden, Uppsala
Who joined Nov. 11, 2009, 12:02 p.m.

Wrote the following at Jan. 14, 2010, 1:20 p.m...

My first SGI computer.

Got it up and running thanks to great help from Ian Mapleson, thank you.


   fuel 3# hinv -mv
   

   Location: /hw/module/001c01/node
   

   IP34 Board: barcode MMN567     part 030-1707-003 rev -H
   

   Location: /hw/module/001c01/node/cpubus/0
   

   IP34PIMM Board: barcode MMR544     part 030-1708-002 rev -H
   

   Location: /hw/module/001c01/Ibrick/xtalk/13
   

   ASTODYB Board: barcode MPF954     part 030-1725-001 rev -F
   

   Location: /hw/module/001c01/Ibrick/xtalk/14
   

   IP34 Board: barcode MMN567     part 030-1707-003 rev -H
   

   Location: /hw/module/001c01/Ibrick/xtalk/15
   

   IP34 Board: barcode MMN567     part 030-1707-003 rev -H
   

   1 500 MHZ IP35 Processor
   

   CPU: MIPS R14000 Processor Chip Revision: 2.3
   

   FPU: MIPS R14010 Floating Point Chip Revision: 2.3
   

   CPU 0 at Module 001c01/Slot 0/Slice A: 500 Mhz MIPS R14000 Processor Chip (enabled)
   

   Processor revision: 2.3. Scache: Size 2 MB Speed 250 Mhz  Tap 0x1a
   

   Main memory size: 1024 Mbytes
   

   Instruction cache size: 32 Kbytes
   

   Data cache size: 32 Kbytes
   

   Secondary unified instruction/data cache size: 2 Mbytes
   

   Memory at Module 001c01/Slot 0: 1024 MB (enabled)
   

   Bank 0 contains 256 MB (Standard) DIMMS (enabled)
   

   Bank 1 contains 256 MB (Standard) DIMMS (enabled)
   

   Bank 2 contains 256 MB (Standard) DIMMS (enabled)
   

   Bank 3 contains 256 MB (Standard) DIMMS (enabled)
   

   Integral SCSI controller 0: Version QL12160, low voltage differential
   

   Disk drive: unit 1 on SCSI controller 0 (unit 1)
   

   Integral SCSI controller 1: Version QL12160, low voltage differential
   

   IOC3/IOC4 serial port: tty1
   

   IOC3/IOC4 serial port: tty2
   

   IOC3 parallel port: plp1
   

   Graphics board: V10
   

   Integral Fast Ethernet: ef0, version 1, module 001c01, pci 4
   

   PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
   

   PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
   

   PCI Adapter ID (vendor 0x11c1, device 0x5802) PCI slot 5
   

   HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
   

   IP35prom in Module 001c01/Slot n0: Revision 6.124
   

   USB controller: type OHCI
   

   fuel 4#

Best regards,
/Christer

ramq
From Sweden
Who joined Jan. 25, 2008, 6:06 a.m.

Wrote the following at Jan. 14, 2010, 1:53 p.m...

Hi, and welcome to the club.
I see you haven't typed in your location yet, so we can't say for sure if there's forum friends close to you or in the same country.

agkbill
From Sweden, Uppsala
Who joined Nov. 11, 2009, 12:02 p.m.

Wrote the following at Jan. 15, 2010, 12:36 a.m...

Thank you!

I am located in Uppsala, Sweden.

Need to update my info.

Best regards,
/Christer

mila
From Bålsta, Sweden
Who joined Dec. 31, 2009, 4:20 a.m.

Wrote the following at Jan. 15, 2010, 9:14 a.m...

agkbill wrote: Thank you!

I am located in Uppsala, Sweden.

Need to update my info.

Best regards,
/Christer

Ops, then you actually have a friend close by in Bålsta about 50km SW, and that strange guy have a much poorer Indigo2 and a Origin200, and some 20 Suns ...

--
No Microsoft product was used in any way to write or send this text.
If you use a Microsoft product to read it, you're doing so at your own
risk.

ramq
From Sweden
Who joined Jan. 25, 2008, 6:06 a.m.

Wrote the following at Jan. 15, 2010, 2:08 p.m...

Uppsala? Well, välkommen till SGI-klubben.

mila
From Bålsta, Sweden
Who joined Dec. 31, 2009, 4:20 a.m.

Wrote the following at Jan. 15, 2010, 2:27 p.m...

3 stycken från Svedala

--
No Microsoft product was used in any way to write or send this text.
If you use a Microsoft product to read it, you're doing so at your own
risk.

ramq
From Sweden
Who joined Jan. 25, 2008, 6:06 a.m.

Wrote the following at Jan. 15, 2010, 4:42 p.m...

There's more - Tesla, deBug, bjornl, Pontus and sgtprobe too. I've probably missed someone.
Pontus, btw, is also from Uppsala.

agkbill
From Sweden, Uppsala
Who joined Nov. 11, 2009, 12:02 p.m.

Wrote the following at Jan. 16, 2010, 3:08 a.m...

Wow, great to see that there are more Swedes here.

It sure is cool machines, now I "just" have to find out how to compile from source code on these. I would like to get a never version of Puredate ( www.puredata.info ) together with the OpenGL add on GEM up and running on my fuel.

But until then I will first change the fans, have successfully changed powersupply and CPU 120MM fans, now it is time for thous noisy 60MM fans

All the best!

/Christer

ramq
From Sweden
Who joined Jan. 25, 2008, 6:06 a.m.

Wrote the following at Jan. 16, 2010, 5:20 a.m...

I've replaced all but the PCI-fan (didn't make much noise) and the Power Supply fan - which sounds like a jet taking off after just a few minutes of runtime.

What fan did you replace the PSU fan with? Model? Manufacturer?
(Did you have to circumvent enviromental monitoring or did it work anyway?)

agkbill
From Sweden, Uppsala
Who joined Nov. 11, 2009, 12:02 p.m.

Wrote the following at Jan. 16, 2010, 6:11 a.m...

The powersupply fan I replaced with a akasa FT-35A.

It is a two pinn fan with thermal sensor.

1200-2600 RPM
18-30,5 dB(A)
15,84-35,32 CFM

Works great in the powersupply due to the built in RPM regulation. I have not disabled the fuel enviroment monitoring.

I can rally recomend this fan for powersupply.

/Christrer

Pontus
From Uppsala, Sweden
Who joined May 8, 2008, 12:12 p.m.

Wrote the following at Nov. 23, 2010, 12:59 a.m...

Hi, welcome and Nice Machine!

Whereabouts in Uppsala are you? I live in Storvreta, but work "downtown".

mila wrote: Ops, then you actually have a friend close by in Bålsta about 50km SW, and that strange guy have a much poorer Indigo2 and a Origin200, and some 20 Suns...

What strange guy? Not me I hope, I gave away all my suns you know