SGI: hinv

Fuel ~ new to me R14 600

s0ke
From TX
Who joined Feb. 24, 2003, 8:27 a.m.

Wrote the following at Aug. 20, 2014, 12:54 p.m...

Recently swapped my Octane2 for a Fuel from TeamBlackFox.


   redmenace 17# hinv -vm
   

   Location: /hw/module/001c01/node
   

   IP34 Board: barcode MZK064     part 030-1707-003 rev -M
   

   Location: /hw/module/001c01/Ibrick/xtalk/13
   

   ASTODYV10 Board: barcode MZL917     part 030-1826-001 rev -B
   

   Location: /hw/module/001c01/Ibrick/xtalk/14
   

   IP34 Board: barcode MZK064     part 030-1707-003 rev -M
   

   Location: /hw/module/001c01/Ibrick/xtalk/15
   

   IP34 Board: barcode MZK064     part 030-1707-003 rev -M
   

   1 600 MHZ IP35 Processor
   

   CPU: MIPS R14000 Processor Chip Revision: 2.4
   

   FPU: MIPS R14010 Floating Point Chip Revision: 2.4
   

   CPU 0 at Module 001c01/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabled)
   

   Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
   

   Main memory size: 2048 Mbytes
   

   Instruction cache size: 32 Kbytes
   

   Data cache size: 32 Kbytes
   

   Secondary unified instruction/data cache size: 4 Mbytes
   

   Memory at Module 001c01/Slot 0: 2048 MB (enabled)
   

   Bank 0 contains 512 MB (Standard) DIMMS (enabled)
   

   Bank 1 contains 512 MB (Standard) DIMMS (enabled)
   

   Bank 2 contains 512 MB (Standard) DIMMS (enabled)
   

   Bank 3 contains 512 MB (Standard) DIMMS (enabled)
   

   Integral SCSI controller 0: Version QL12160, low voltage differential
   

   Disk drive: unit 1 on SCSI controller 0 (unit 1)
   

   Disk drive: unit 2 on SCSI controller 0 (unit 2)
   

   Integral SCSI controller 1: Version QL12160, single ended
   

   CDROM: unit 6 on SCSI controller 1
   

   IOC3/IOC4 serial port: tty1
   

   IOC3/IOC4 serial port: tty2
   

   IOC3 parallel port: plp1
   

   Graphics board: V10
   

   Gigabit Ethernet: eg0, module 001c01, pci_bus 1, pci_slot 2, firmware version 12.4.10
   

   Integral Fast Ethernet: ef0, version 1, module 001c01, pci 4
   

   PCI Adapter ID (vendor 4215, device 4630) pci slot 1
   

   PCI Adapter ID (vendor 4265, device 9) pci slot 2
   

   PCI Adapter ID (vendor 4265, device 3) pci slot 4
   

   PCI Adapter ID (vendor 4165, device 51297) pci slot 5
   

   HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
   

   IP35prom in Module 001c01/Slot n0: Revision 6.210
   

   USB controller: type OHCI

Code: Select all


   redmenace 22# ./gfxinfo -vv
   

   Graphics board 0 is "ODYSSEY" graphics.
   

   Managed (":0.0") 1280x1024
   

   BUZZ version B.1
   

   PB&J version 1
   

   32MB memory
   

   Banks: 2, CAS latency: 3
   

   Monitor 0 type: ACR 515
   

   Input Sync: Voltage - Video Level; Source - Internal; Genlocked - False
   

   Channel 0:
   

   Origin = (0,0)
   

   Video Output: 1280 pixels, 1024 lines, 60.00Hz (1280x1024_60)
   

   Video Format Flags:  (none)
   

   Sync Disabled
   

   Using Gamma Map 0
   

   Monitor Type:  ACR-515
   

   Gain (all color components) - 0.000000 ; range [1,10]

Code: Select all


   redmenace 1% uname -aR
   

   IRIX64 redmenace 6.5 6.5.30f 07202013 IP35

Just upgraded thanks to mopar5150

Code: Select all


   Location: /hw/module/001c01/node
   

   IP34 Board: barcode MZK064     part 030-1707-003 rev -M
   

   Location: /hw/module/001c01/node/cpubus/0
   

   IP34PIMM Board: barcode MXF981     part 030-1891-001 rev -D
   

   Location: /hw/module/001c01/Ibrick/xtalk/13
   

   ASTODYV10 Board: barcode MZL917     part 030-1826-001 rev -B
   

   Location: /hw/module/001c01/Ibrick/xtalk/14
   

   IP34 Board: barcode MZK064     part 030-1707-003 rev -M
   

   Location: /hw/module/001c01/Ibrick/xtalk/15
   

   IP34 Board: barcode MZK064     part 030-1707-003 rev -M
   

   1 700 MHZ IP35 Processor
   

   CPU: MIPS R16000 Processor Chip Revision: 2.1
   

   FPU: MIPS R16010 Floating Point Chip Revision: 2.1
   

   CPU 0 at Module 001c01/Slot 0/Slice A: 700 Mhz MIPS R16000 Processor Chip (enabled)
   

   Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xa

Redmenace

Trippynet
Who joined Aug. 15, 2013, 6:22 a.m.

Wrote the following at Aug. 23, 2014, 9:11 a.m...

Never said the Indigo2 was loud, that's the Tezro. Well, the I2 a fair bit noisier than a modern PC (obviously), but it's not difficult to replace the fans. I did that with mine and my Indigo2 now only makes a quiet humming noise as a result. My Fuel (stock fans) is much louder.

Systems in use:
:Fuel:

- Lithium : R14000 600MHz CPU, 4GB RAM, V10 Graphics, 36GB 15k HDD & 300GB 10k HDD, New/quiet fans, IRIX 6.5.30
:Indigo2IMP:

- Nitrogen : R10000 195MHz CPU, 384MB RAM, SolidIMPACT Graphics, 36GB 15k HDD & 300GB 10k HDD, New/quiet fans, IRIX 6.5.22
Other systems in storage: :O2:

x 2,

x 2