SGI: hinv

Fuel, 600Mhz, 1G RAM, 18GB HDD, V10, ATX PSU

kubatyszko
Who joined Nov. 12, 2011, 3:18 a.m.
and authored 308 notes
Wrote the following at Oct. 31, 2012, 5:27 a.m...
hinv -vm
Code:
Location: /hw/module/001c01/node
IP34 Board: barcode MYD069     part 030-1707-003 rev -L
Location: /hw/module/001c01/node/cpubus/0
IP34PIMM Board: barcode MKZ626     part 030-1730-001 rev -G
Location: /hw/module/001c01/Ibrick/xtalk/13
ASTODYV10 Board: barcode MXH355     part 030-1826-002 rev -A
Location: /hw/module/001c01/Ibrick/xtalk/14
IP34 Board: barcode MYD069     part 030-1707-003 rev -L
Location: /hw/module/001c01/Ibrick/xtalk/15
IP34 Board: barcode MYD069     part 030-1707-003 rev -L
1 600 MHZ IP35 Processor
CPU: MIPS R14000 Processor Chip Revision: 2.3
FPU: MIPS R14010 Floating Point Chip Revision: 2.3
CPU 0 at Module 001c01/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabled)
Processor revision: 2.3. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
Main memory size: 1024 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 4 Mbytes
Memory at Module 001c01/Slot 0: 1024 MB (enabled)
Bank 0 contains 256 MB (Standard) DIMMS (enabled)
Bank 1 contains 256 MB (Standard) DIMMS (enabled)
Bank 2 contains 256 MB (Standard) DIMMS (enabled)
Bank 3 contains 256 MB (Standard) DIMMS (enabled)
Integral SCSI controller 0: Version QL12160, low voltage differential
Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL12160, single ended
CDROM: unit 1 on SCSI controller 1
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V10
Integral Fast Ethernet: ef0, version 1, module 001c01, pci 4
PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
PCI Adapter ID (vendor 0x1045, device 0xc861) PCI slot 5
HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
IP35prom in Module 001c01/Slot n0: Revision 6.210
USB controller: type OHCI




/usr/gfx/gfxinfo -vv
Code:
Graphics board 0 is "ODYSSEY" graphics.
Managed (":0.0") 1280x1024
BUZZ version B.2
PB&J version 1
32MB memory
Banks: 2, CAS latency: 3
Monitor 0 type: Unknown
(Could not contact X server; thus, no XSGIvc information available)


uname -aR
Code:
IRIX64 Fuel 6.5 6.5.30m 07202013 IP35



scsicontrol -i /dev/scsi/*
Code:
/dev/scsi/sc0d1l0:  Disk          SGI     ST318406LW      2006
ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing
Device is  ready
/dev/scsi/sc1d1l0:  CD-ROM        TOSHIBA DVD-ROM SD-M14011007
ANSI vers 2, ISO ver: 0, ECMA ver: 0; supports:  synch linkedcmds
Device is  not ready


/sbin/diskpatch -v
Code:
sc0d1l0:  Disk         SGI     ST318406LW      2006  Serial: 3FE21ELG




l1cmd serial all
Code:
Data                            Location      Value
------------------------------  ------------  --------
Local System Serial Number      EEPROM        08:00:69:10:62:A3
Local Brick Serial Number       EEPROM        MYD069
Reference Brick Serial Number   NVRAM         MYD069


EEPROM      Product Name    Serial      Part Number           Rev  T/W
----------  --------------  ----------  --------------------  ---  ------
NODE        IP34            MYD069      030_1707_003          L    00
MAC         MAC ADDRESS     NA          NA                    NA   NA
PIMM        IP34PIMM        MKZ626      030_1730_001          G    00
XIO         ASTODYV10       MXH355      030_1826_002          A    00

EEPROM     JEDEC-SPD Info           Part Number        Rev Speed  SGI
---------- ------------------------ ------------------ --- ------ --------
DIMM 0     CE000000000000000CFE7000 M3 46L3313DT2-CA0  2D   10.0  N/A
DIMM 2     CE000000000000000CFF7000 M3 46L3313DT2-CA0  2D   10.0  N/A
DIMM 1     CE000000000000000C5BAD02 M3 46L3313DT2-CA0  2D   10.0  N/A
DIMM 3     CE000000000000000C65AD02 M3 46L3313DT2-CA0  2D   10.0  N/A


l1cmd flash status
Code:
Flash image A currently booted

Image      Status        Revision    Built
-----   -------------   ----------   -----
A     user default    1.20.6       03/12/2003 11:01:29
B     valid           1.20.6       03/12/2003 11:01:29


l1cmd env
Code:
Environmental monitoring is enabled and running.

Description    State       Warning Limits     Fault Limits       Current
-------------- ----------  -----------------  -----------------  -------
12V    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   11.50
12V IO    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   11.81
5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.20
3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.30
2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.46
1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.47
5V aux    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.02
3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.27
PIMM0 12V bias    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   11.81
Fuel SRAM    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.54
Fuel CPU    Enabled  10%   1.44/  1.76  20%   1.28/  1.92    1.59
PIMM0 1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.49
PIMM0 3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.29
PIMM0 5V aux    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.04
XIO 12V bias    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   11.44
XIO 5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.20
XIO 2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.46
XIO 3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.30

Description    State       Warning RPM  Current RPM
-------------- ----------  -----------  -----------
FAN 0  EXHAUST    Enabled          920         1228
FAN 1       HD    Enabled         1560         2244
FAN 2      PCI    Enabled         1120         1558
FAN 3    XIO 1    Enabled         1600         2274
FAN 4    XIO 2    Enabled         1600         2130
FAN 5       PS    Enabled         1600         1781

Advisory   Critical   Fault      Current
Description    State       Temp       Temp       Temp       Temp
-------------- ----------  ---------  ---------  ---------  ---------
NODE 0            Enabled   60C/140F   65C/149F   70C/158F   33C/ 91F
NODE 1            Enabled   60C/140F   65C/149F   70C/158F   31C/ 87F
NODE 2            Enabled   60C/140F   65C/149F   70C/158F   23C/ 73F
PIMM              Enabled   60C/140F   65C/149F   70C/158F   40C/104F
ODYSSEY           Enabled   60C/140F   65C/149F   70C/158F   29C/ 84F
BEDROCK           Enabled   70C/158F   75C/167F   80C/176F   34C/ 93F

_________________
[click for links to hinv] JP: [ :O200: :Fuel: :Octane2: :Octane: :O2: :Indy: :Indy: ] PL: [ :Fuel: :O2: :O2+: :Indy: ]
For Sale: 2*O200 M/B, 2*O200 PSU, 6*256MB O200 RAM, 2*O200 SCSI Backplane, 2*O200 MSC, DMediaPro DM-2 ( 030-1653-002 Rev. H , XT-DIGVID) with Octane XIO pull (Origin pull optionally available)