After a couple of weeks regretting that I couldn't go for Pontus Onyx2 rack deal, I had to finish my deskside setup to feel better.
I've had it for a while, but I thought there was room for improvement. Thank you tesla for the last missing bit.
hinv -vm
/usr/gfx/gfxinfo -v
There is also a FORE PCA-200E ATM adapter in the PCI box. It doesn't show up in the hinv. I guess it's because I don't have the drivers for it. I don't
have anything to connect it to anyway.
I do however have a Clariion FC Raid connected to this, but I have some problems getting it to run properly again, after I made some reconfiguration.
Pictures will be added as soon as I have removed some of the other computerstuff blocking it
I've had it for a while, but I thought there was room for improvement. Thank you tesla for the last missing bit.
hinv -vm
Code:
Location: /hw/module/1/slot/n2/node
IP31 Board: barcode JEG911 part 030-1255-003 rev D
IP31PIMM8MB Board: barcode JDW175 part 030-1401-002 rev B
Location: /hw/module/1/slot/n1/node
MODULEID Board: barcode K0009799 part rev
IP31 Board: barcode JDY444 part 030-1255-003 rev D
IP31PIMM8MB Board: barcode JGV637 part 030-1401-002 rev B
4P1G5_MPLN Board: barcode DKA422 part 013-1839-001 rev E
Location: /hw/module/1/slot/io4/kona
GE14-4 Board: barcode FSV343 part 030-1129-002 rev F
Location: /hw/module/1/slot/io2/pci_xio
PCI-XIO Board: barcode FSW690 part 030-1062-002 rev D
Location: /hw/module/1/slot/io6/fibre_channel
FIBRE_CHANNEL Board: barcode JJB245 part 030-0927-003 rev E
Location: /hw/module/1/slot/io5/divo
DIVO Board: barcode DGR358 part 030-1046-002 rev F
Location: /hw/module/1/slot/io3/menet
MENET Board: barcode HPS515 part 030-0873-003 rev J
Location: /hw/module/1/slot/io1/baseio
BASEIO Board: barcode ENG320 part 030-0734-002 rev D
MIO Board: barcode EYZ091 part 030-0880-003 rev E
4 300 MHZ IP27 Processors
CPU: MIPS R12000 Processor Chip Revision: 2.3
FPU: MIPS R12010 Floating Point Chip Revision: 2.3
CPU 0 at Module 1/Slot 2/Slice A: 300 Mhz MIPS R12000 Processor Chip (enabled)
Processor revision: 2.3. Scache: Size 8 MB Speed 200 Mhz Tap 0xa
CPU 1 at Module 1/Slot 2/Slice B: 300 Mhz MIPS R12000 Processor Chip (enabled)
Processor revision: 2.3. Scache: Size 8 MB Speed 200 Mhz Tap 0xa
CPU 2 at Module 1/Slot 1/Slice A: 300 Mhz MIPS R12000 Processor Chip (enabled)
Processor revision: 2.3. Scache: Size 8 MB Speed 200 Mhz Tap 0xa
CPU 3 at Module 1/Slot 1/Slice B: 300 Mhz MIPS R12000 Processor Chip (enabled)
Processor revision: 2.3. Scache: Size 8 MB Speed 200 Mhz Tap 0xa
Main memory size: 8192 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 8 Mbytes
Memory at Module 1/Slot 82: 4096 MB (enabled)
Bank 0 contains 512 MB (Standard) DIMMS (enabled)
Bank 1 contains 512 MB (Standard) DIMMS (enabled)
Bank 2 contains 512 MB (Standard) DIMMS (enabled)
Bank 3 contains 512 MB (Standard) DIMMS (enabled)
Bank 4 contains 512 MB (Standard) DIMMS (enabled)
Bank 5 contains 512 MB (Standard) DIMMS (enabled)
Bank 6 contains 512 MB (Standard) DIMMS (enabled)
Bank 7 contains 512 MB (Standard) DIMMS (enabled)
Memory at Module 1/Slot 81: 4096 MB (enabled)
Bank 0 contains 512 MB (Standard) DIMMS (enabled)
Bank 1 contains 512 MB (Standard) DIMMS (enabled)
Bank 2 contains 512 MB (Standard) DIMMS (enabled)
Bank 3 contains 512 MB (Standard) DIMMS (enabled)
Bank 4 contains 512 MB (Standard) DIMMS (enabled)
Bank 5 contains 512 MB (Standard) DIMMS (enabled)
Bank 6 contains 512 MB (Standard) DIMMS (enabled)
Bank 7 contains 512 MB (Standard) DIMMS (enabled)
Integral SCSI controller 4: Version Fibre Channel AIC-1160, revision 2
Integral SCSI controller 5: Version Fibre Channel AIC-1160, revision 2
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
Disk drive: unit 1 on SCSI controller 0 (unit 1)
CDROM: unit 6 on SCSI controller 0
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
IOC3/IOC4 serial port: tty7
IOC3/IOC4 serial port: tty8
IOC3/IOC4 serial port: tty9
IOC3/IOC4 serial port: tty10
IOC3/IOC4 serial port: tty11
IOC3/IOC4 serial port: tty12
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3/IOC4 serial port: tty3
IOC3/IOC4 serial port: tty4
IOC3 parallel port: plp1
Graphics board: InfiniteReality2
Fast Ethernet: ef1, version 1, module 1, slot io3, pci 0
Fast Ethernet: ef2, version 1, module 1, slot io3, pci 1
Fast Ethernet: ef3, version 1, module 1, slot io3, pci 2
Fast Ethernet: ef4, version 1, module 1, slot io3, pci 3
Integral Fast Ethernet: ef0, version 1, module 1, slot io1, pci 2
Iris Audio Processor: version RAD revision 7.0, number 1
Origin PCI XIO board, module 1 slot 2: Revision 3
Origin FIBRE CHANNEL board, module 1 slot 6: Revision 4
PCI Adapter ID (vendor 0x1127, device 0x0300) PCI slot 0
PCI Adapter ID (vendor 0x9004, device 0x1160) PCI slot 0
PCI Adapter ID (vendor 0x9004, device 0x1160) PCI slot 1
PCI Adapter ID (vendor 0x10a9, device 0x0002) PCI slot 0
PCI Adapter ID (vendor 0x10a9, device 0x0002) PCI slot 2
Origin MENET board, module 1 slot 3: Revision 4
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 0
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 1
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 3
Origin BASEIO board, module 1 slot 1: Revision 3
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 6
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 7
DIVO Video: controller 0 unit 0: Input, Output
IOC3/IOC4 external interrupts: 1
HUB in Module 1/Slot 2: Revision 5 Speed 100.00 Mhz (enabled)
HUB in Module 1/Slot 1: Revision 5 Speed 100.00 Mhz (enabled)
IP27prom in Module 1/Slot n2: Revision 6.156
IP27prom in Module 1/Slot n1: Revision 6.156
IO6prom on Global Master Baseio in Module 1/Slot io2: Revision 6.156
IP31 Board: barcode JEG911 part 030-1255-003 rev D
IP31PIMM8MB Board: barcode JDW175 part 030-1401-002 rev B
Location: /hw/module/1/slot/n1/node
MODULEID Board: barcode K0009799 part rev
IP31 Board: barcode JDY444 part 030-1255-003 rev D
IP31PIMM8MB Board: barcode JGV637 part 030-1401-002 rev B
4P1G5_MPLN Board: barcode DKA422 part 013-1839-001 rev E
Location: /hw/module/1/slot/io4/kona
GE14-4 Board: barcode FSV343 part 030-1129-002 rev F
Location: /hw/module/1/slot/io2/pci_xio
PCI-XIO Board: barcode FSW690 part 030-1062-002 rev D
Location: /hw/module/1/slot/io6/fibre_channel
FIBRE_CHANNEL Board: barcode JJB245 part 030-0927-003 rev E
Location: /hw/module/1/slot/io5/divo
DIVO Board: barcode DGR358 part 030-1046-002 rev F
Location: /hw/module/1/slot/io3/menet
MENET Board: barcode HPS515 part 030-0873-003 rev J
Location: /hw/module/1/slot/io1/baseio
BASEIO Board: barcode ENG320 part 030-0734-002 rev D
MIO Board: barcode EYZ091 part 030-0880-003 rev E
4 300 MHZ IP27 Processors
CPU: MIPS R12000 Processor Chip Revision: 2.3
FPU: MIPS R12010 Floating Point Chip Revision: 2.3
CPU 0 at Module 1/Slot 2/Slice A: 300 Mhz MIPS R12000 Processor Chip (enabled)
Processor revision: 2.3. Scache: Size 8 MB Speed 200 Mhz Tap 0xa
CPU 1 at Module 1/Slot 2/Slice B: 300 Mhz MIPS R12000 Processor Chip (enabled)
Processor revision: 2.3. Scache: Size 8 MB Speed 200 Mhz Tap 0xa
CPU 2 at Module 1/Slot 1/Slice A: 300 Mhz MIPS R12000 Processor Chip (enabled)
Processor revision: 2.3. Scache: Size 8 MB Speed 200 Mhz Tap 0xa
CPU 3 at Module 1/Slot 1/Slice B: 300 Mhz MIPS R12000 Processor Chip (enabled)
Processor revision: 2.3. Scache: Size 8 MB Speed 200 Mhz Tap 0xa
Main memory size: 8192 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 8 Mbytes
Memory at Module 1/Slot 82: 4096 MB (enabled)
Bank 0 contains 512 MB (Standard) DIMMS (enabled)
Bank 1 contains 512 MB (Standard) DIMMS (enabled)
Bank 2 contains 512 MB (Standard) DIMMS (enabled)
Bank 3 contains 512 MB (Standard) DIMMS (enabled)
Bank 4 contains 512 MB (Standard) DIMMS (enabled)
Bank 5 contains 512 MB (Standard) DIMMS (enabled)
Bank 6 contains 512 MB (Standard) DIMMS (enabled)
Bank 7 contains 512 MB (Standard) DIMMS (enabled)
Memory at Module 1/Slot 81: 4096 MB (enabled)
Bank 0 contains 512 MB (Standard) DIMMS (enabled)
Bank 1 contains 512 MB (Standard) DIMMS (enabled)
Bank 2 contains 512 MB (Standard) DIMMS (enabled)
Bank 3 contains 512 MB (Standard) DIMMS (enabled)
Bank 4 contains 512 MB (Standard) DIMMS (enabled)
Bank 5 contains 512 MB (Standard) DIMMS (enabled)
Bank 6 contains 512 MB (Standard) DIMMS (enabled)
Bank 7 contains 512 MB (Standard) DIMMS (enabled)
Integral SCSI controller 4: Version Fibre Channel AIC-1160, revision 2
Integral SCSI controller 5: Version Fibre Channel AIC-1160, revision 2
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
Disk drive: unit 1 on SCSI controller 0 (unit 1)
CDROM: unit 6 on SCSI controller 0
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
IOC3/IOC4 serial port: tty7
IOC3/IOC4 serial port: tty8
IOC3/IOC4 serial port: tty9
IOC3/IOC4 serial port: tty10
IOC3/IOC4 serial port: tty11
IOC3/IOC4 serial port: tty12
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3/IOC4 serial port: tty3
IOC3/IOC4 serial port: tty4
IOC3 parallel port: plp1
Graphics board: InfiniteReality2
Fast Ethernet: ef1, version 1, module 1, slot io3, pci 0
Fast Ethernet: ef2, version 1, module 1, slot io3, pci 1
Fast Ethernet: ef3, version 1, module 1, slot io3, pci 2
Fast Ethernet: ef4, version 1, module 1, slot io3, pci 3
Integral Fast Ethernet: ef0, version 1, module 1, slot io1, pci 2
Iris Audio Processor: version RAD revision 7.0, number 1
Origin PCI XIO board, module 1 slot 2: Revision 3
Origin FIBRE CHANNEL board, module 1 slot 6: Revision 4
PCI Adapter ID (vendor 0x1127, device 0x0300) PCI slot 0
PCI Adapter ID (vendor 0x9004, device 0x1160) PCI slot 0
PCI Adapter ID (vendor 0x9004, device 0x1160) PCI slot 1
PCI Adapter ID (vendor 0x10a9, device 0x0002) PCI slot 0
PCI Adapter ID (vendor 0x10a9, device 0x0002) PCI slot 2
Origin MENET board, module 1 slot 3: Revision 4
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 0
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 1
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 3
Origin BASEIO board, module 1 slot 1: Revision 3
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 6
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 7
DIVO Video: controller 0 unit 0: Input, Output
IOC3/IOC4 external interrupts: 1
HUB in Module 1/Slot 2: Revision 5 Speed 100.00 Mhz (enabled)
HUB in Module 1/Slot 1: Revision 5 Speed 100.00 Mhz (enabled)
IP27prom in Module 1/Slot n2: Revision 6.156
IP27prom in Module 1/Slot n1: Revision 6.156
IO6prom on Global Master Baseio in Module 1/Slot io2: Revision 6.156
/usr/gfx/gfxinfo -v
Code:
Graphics board 0 is "KONAL" graphics.
Managed (":0.0") 1280x1024
Display has 8 channels
4 GEs (of 4), occmask = 0x0f
4MB external BEF ram, 32bit path
2 RM7 boards (of 2) 1/1/0/0
Texture Memory: 64MB/64MB/-/-
Medium pixel depth
32K cmap, 64K external gamma
brd: 80160a04 3020c06/3020c06/-/- 51bf1002
ge: 0 14832057 24731057 14231057
rm0: 15032057 15431057
4631057 1/1/1/1
4d31057 2/2/2/2/2/2/2/2
4938057 4/4/4/4/4/4/4/4/4/4/4/4/4/4/4/4/4/4/4/4
rm1: 15032057 15431057
4631057 2/2/2/2
4d31057 2/2/2/2/2/2/2/2
4938057 5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5
dg: 05532057
5838057 1/1/1/1
5631057 1/1/1/1/1/1/1/1
GE: NIC #: 0000.0014.0524 (family: 0b)
Serial #: FSV343
Part #: 030-1129-002
KT: No NIC serial number available.
RM0: NIC #: 0000.000f.6c9c (family: 0b)
Serial #: DCM903
Part #: 030-1054-001
TM0: NIC #: 0000.000e.ad47 (family: 0b)
Serial #: DCM351
Part #: 030-1053-001
RM1: NIC #: 0000.0019.0785 (family: 0b)
Serial #: EDX572
Part #: 030-1054-001
TM1: NIC #: 0000.0019.05e4 (family: 0b)
Serial #: EDX831
Part #: 030-1053-001
RM2: No NIC serial number available.
TM2: No NIC serial number available.
RM3: No NIC serial number available.
TM3: No NIC serial number available.
BP: No NIC serial number available.
DG: NIC #: 0000.0016.159d (family: 0b)
Serial #: ENG807
Part #: 030-1087-001
DGOPT:No NIC serial number available.
Input Sync: Voltage - Video Level; Source - Internal; Genlocked - False
Channel 0:
Origin = (0,0)
Video Output: 1280 pixels, 1024 lines, 60.00Hz (1280x1024_60.vfo)
Video Format Flags: (none)
Sync Output(s):
Composite sync on Green
Composite TTL sync on Aux 0
Using Gamma Map 0
Channel 1:
Channel's Source Size: 1280 pixels, 1024 lines; Origin = (0,0)
Video Output: 640 pixels, 486 lines, 29.97Hz (640x486_30i.vfo)
Video Format Flags: (none)
Sync Output(s):
Composite sync on Green
Horizontal TTL sync on Aux 0
Using Gamma Map 0
Managed (":0.0") 1280x1024
Display has 8 channels
4 GEs (of 4), occmask = 0x0f
4MB external BEF ram, 32bit path
2 RM7 boards (of 2) 1/1/0/0
Texture Memory: 64MB/64MB/-/-
Medium pixel depth
32K cmap, 64K external gamma
brd: 80160a04 3020c06/3020c06/-/- 51bf1002
ge: 0 14832057 24731057 14231057
rm0: 15032057 15431057
4631057 1/1/1/1
4d31057 2/2/2/2/2/2/2/2
4938057 4/4/4/4/4/4/4/4/4/4/4/4/4/4/4/4/4/4/4/4
rm1: 15032057 15431057
4631057 2/2/2/2
4d31057 2/2/2/2/2/2/2/2
4938057 5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5
dg: 05532057
5838057 1/1/1/1
5631057 1/1/1/1/1/1/1/1
GE: NIC #: 0000.0014.0524 (family: 0b)
Serial #: FSV343
Part #: 030-1129-002
KT: No NIC serial number available.
RM0: NIC #: 0000.000f.6c9c (family: 0b)
Serial #: DCM903
Part #: 030-1054-001
TM0: NIC #: 0000.000e.ad47 (family: 0b)
Serial #: DCM351
Part #: 030-1053-001
RM1: NIC #: 0000.0019.0785 (family: 0b)
Serial #: EDX572
Part #: 030-1054-001
TM1: NIC #: 0000.0019.05e4 (family: 0b)
Serial #: EDX831
Part #: 030-1053-001
RM2: No NIC serial number available.
TM2: No NIC serial number available.
RM3: No NIC serial number available.
TM3: No NIC serial number available.
BP: No NIC serial number available.
DG: NIC #: 0000.0016.159d (family: 0b)
Serial #: ENG807
Part #: 030-1087-001
DGOPT:No NIC serial number available.
Input Sync: Voltage - Video Level; Source - Internal; Genlocked - False
Channel 0:
Origin = (0,0)
Video Output: 1280 pixels, 1024 lines, 60.00Hz (1280x1024_60.vfo)
Video Format Flags: (none)
Sync Output(s):
Composite sync on Green
Composite TTL sync on Aux 0
Using Gamma Map 0
Channel 1:
Channel's Source Size: 1280 pixels, 1024 lines; Origin = (0,0)
Video Output: 640 pixels, 486 lines, 29.97Hz (640x486_30i.vfo)
Video Format Flags: (none)
Sync Output(s):
Composite sync on Green
Horizontal TTL sync on Aux 0
Using Gamma Map 0
There is also a FORE PCA-200E ATM adapter in the PCI box. It doesn't show up in the hinv. I guess it's because I don't have the drivers for it. I don't
have anything to connect it to anyway.
I do however have a Clariion FC Raid connected to this, but I have some problems getting it to run properly again, after I made some reconfiguration.
Pictures will be added as soon as I have removed some of the other computerstuff blocking it
