SGI: hinv

Fuel R14k 600mhz 2048MB V12

directedition
Who joined Feb. 4, 2003, 1:20 a.m.
and authored 515 notes
Wrote the following at Jan. 11, 2009, 12:26 a.m...
A special thanks to Zerolapse for giving me a great deal on this system. My highest powered SGI before this was an O2 R10k 195mhz and an Indigo 2 R10k w/ High Impact. This is a HUGE improvement in terms of performance. I love this machine :D

hinv -vm
Code:
Location: /hw/module/001c01/node
IP34 Board: barcode MNV385     part 030-1707-003 rev -H
Location: /hw/module/001c01/node/cpubus/0
IP34PIMM Board: barcode NCN997     part 030-1730-002 rev -E
Location: /hw/module/001c01/Ibrick/xtalk/13
ASTODY Board: barcode NAT871     part 030-1726-005 rev -A
Location: /hw/module/001c01/Ibrick/xtalk/14
IP34 Board: barcode MNV385     part 030-1707-003 rev -H
Location: /hw/module/001c01/Ibrick/xtalk/15
IP34 Board: barcode MNV385     part 030-1707-003 rev -H
1 600 MHZ IP35 Processor
CPU: MIPS R14000 Processor Chip Revision: 2.4
FPU: MIPS R14010 Floating Point Chip Revision: 2.4
CPU 0 at Module 001c01/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabled)
Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
Main memory size: 2048 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 4 Mbytes
Memory at Module 001c01/Slot 0: 2048 MB (enabled)
Bank 0 contains 512 MB (Standard) DIMMS (enabled)
Bank 1 contains 512 MB (Standard) DIMMS (enabled)
Bank 2 contains 512 MB (Standard) DIMMS (enabled)
Bank 3 contains 512 MB (Standard) DIMMS (enabled)
Integral SCSI controller 0: Version QL12160, low voltage differential
Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL12160, single ended
CDROM: unit 6 on SCSI controller 1
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V12
Integral Fast Ethernet: ef0, version 1, module 001c01, pci 4
Iris Audio Processor: version MAD revision 1, number 1
PCI Adapter ID (vendor 0x1412, device 0x1724) PCI slot 2
PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
PCI Adapter ID (vendor 0x11c1, device 0x5802) PCI slot 5
HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
IP35prom in Module 001c01/Slot n0: Revision 6.211
USB controller: type OHCI


gfxinfo:
Code:
Graphics board 0 is "ODYSSEY" graphics.
Managed (":0.0") 1600x1024
BUZZ version B.2
PB&J version 1
128MB memory
Banks: 4, CAS latency: 3
Monitor 0 type: Unknown
Channel 0:
Origin = (0,0)
Video Output: 1600 pixels, 1024 lines, 82.98Hz (1600x1024_83)

_________________
- Jim
:Indigo: :Indigo: :Indy: :Indy: <- signed by The Screensavers :) :Indigo2IMP: (230L) (230L) :540: :1600SW: :1600SW: <- touchscreen :PI: :Octane2:
jan-jaap avatar
jan-jaap
Who joined June 17, 2004, 6:35 p.m.
and authored 3623 notes
Wrote the following at Jan. 14, 2009, 4:23 p.m...
directedition wrote:
Code:
Video Output: 1600 pixels, 1024 lines, 82.98Hz (1600x1024_83)

Hmmm, 83Hz? On a 1600SW or something else?
eMGee wrote:
how is the USB under IRIX?

Awful :lol:

_________________
Now this is a deep dark secret, so everybody keep it quiet :)
It turns out that when reset, the WD33C93 defaults to a SCSI ID of 0, and it was simpler to leave it that way... -- Dave Olson, in comp.sys.sgi
Currently in commercial service: Image :Onyx2: (2x) :O3x02L:
In the museum : almost every MIPS/IRIX system.
Wanted : GM1 board for Professional Series GT graphics (030-0076-003, 030-0076-004)
directedition
Who joined Feb. 4, 2003, 1:20 a.m.
and authored 515 notes
Wrote the following at Jan. 14, 2009, 4:51 p.m...
My 1600SW is just THAT awesome :)

But really, it's driving my FW900 at 1920x1080@72hz right now. I was planning on putting my 1600SW adapter in, but decided against it.

_________________
- Jim
:Indigo: :Indigo: :Indy: :Indy: <- signed by The Screensavers :) :Indigo2IMP: (230L) (230L) :540: :1600SW: :1600SW: <- touchscreen :PI: :Octane2: