Nekonomicon - Onyx 3000, 12x600MHz, 6GB, dual-pipe IR3 with HD-GVO

hirudin
Who joined Sept. 12, 2008, 2:24 p.m.

Wrote the following at Dec. 5, 2008, 12:32 a.m...

Onyx 3000 system, 12x600MHz, 6GB RAM, dual pipe IR3 graphics with 2 channels and 2xRM10's per pipe, an HD-GVO(TVO) board and VBOB with TMDS.
It's taken over a month to learn how this machine works and to get her working:

Code: Select all


   CONFIG:
   

   No. of NODEs enabled    = 3
   

   No. of NODEs disabled   = 0
   

   No. of CPUs enabled     = 12
   

   No. of CPUs disabled    = 0
   

   Mem enabled             = 6144 MB
   

   Mem disabled            = 0 MB
   

   No. of RTRs enabled     = 2
   

   No. of RTRs disabled    = 0
   

   

   DIAG RESULTS:
   

   ALL DIAGS PASSED.
   

   **** End System Configuration and Diagnostics Summary ****

Code: Select all


   IRIS 2% hinv -vm
   

   Location: /hw/module/001c07/node
   

   IP35 Board: barcode MJH109     part 030-1604-006 rev -D
   

   Location: /hw/module/001c07/node/cpubus/0
   

   IP35PIMM Board: barcode MNP457     part 030-1734-002 rev -B
   

   Location: /hw/module/001c07/node/cpubus/1
   

   IP35PIMM Board: barcode MHP324     part 030-1734-001 rev -C
   

   Location: /hw/module/001c07/Ibrick/xtalk/11
   

   GE16-4 Board: barcode KJD735     part 030-1398-002 rev  B
   

   KTOWN2 Board: barcode MHZ137     part 030-1593-001 rev  H
   

   Location: /hw/module/001c07/Ibrick/xtalk/14
   

   IBRICK Board: barcode MJA279     part 030-1557-007 rev -F
   

   Location: /hw/module/001c07/Ibrick/xtalk/15
   

   IBRICK Board: barcode MJA279     part 030-1557-007 rev -F
   

   Location: /hw/module/001c10/node
   

   IP35 Board: barcode MPB287     part 030-1604-005 rev -F
   

   Location: /hw/module/001c10/node/cpubus/0
   

   IP35PIMM Board: barcode MNN802     part 030-1734-002 rev -B
   

   Location: /hw/module/001c10/node/cpubus/1
   

   IP35PIMM Board: barcode MNN739     part 030-1734-002 rev -B
   

   Location: /hw/module/001c10/Xbrick/xtalk/11
   

   GE16-4 Board: barcode KJD716     part 030-1398-002 rev  B
   

   Location: /hw/module/001c10/Xbrick/xtalk/12
   

   HIPPI_SERIAL Board: barcode EBB782     part 030-0968-005 rev  A
   

   Location: /hw/module/001c10/Xbrick/xtalk/14
   

   XBRICK Board: barcode MJA697     part 030-1710-002 rev -B
   

   Location: /hw/module/001c10/Xbrick/xtalk/15
   

   XBRICK Board: barcode MJA697     part 030-1710-002 rev -B
   

   Location: /hw/module/001c13/node
   

   IP35 Board: barcode KJD849     part 030-1604-006 rev -D
   

   Location: /hw/module/001c13/node/cpubus/0
   

   IP35PIMM Board: barcode MJW243     part 030-1734-002 rev -B
   

   Location: /hw/module/001c13/node/cpubus/1
   

   IP35PIMM Board: barcode MJW212     part 030-1734-002 rev -B
   

   Location: /hw/module/001r20/router
   

   ROUTER Board: barcode MAP393     part 030-1634-003 rev -A
   

   Location: /hw/module/001r26/router
   

   ROUTER Board: barcode LGP348     part 030-1634-003 rev -A
   

   Processor 0: 600 MHZ IP35
   

   CPU: MIPS R14000 Processor Chip Revision: 2.4
   

   FPU: MIPS R14010 Floating Point Chip Revision: 2.4
   

   Processor 1: 600 MHZ IP35
   

   CPU: MIPS R14000 Processor Chip Revision: 2.4
   

   FPU: MIPS R14010 Floating Point Chip Revision: 2.4
   

   Processor 2: 600 MHZ IP35
   

   CPU: MIPS R14000 Processor Chip Revision: 2.3
   

   FPU: MIPS R14010 Floating Point Chip Revision: 2.3
   

   Processor 3: 600 MHZ IP35
   

   CPU: MIPS R14000 Processor Chip Revision: 2.3
   

   FPU: MIPS R14010 Floating Point Chip Revision: 2.3
   

   Processor 4: 600 MHZ IP35
   

   CPU: MIPS R14000 Processor Chip Revision: 2.4
   

   FPU: MIPS R14010 Floating Point Chip Revision: 2.4
   

   Processor 5: 600 MHZ IP35
   

   CPU: MIPS R14000 Processor Chip Revision: 2.4
   

   FPU: MIPS R14010 Floating Point Chip Revision: 2.4
   

   Processor 6: 600 MHZ IP35
   

   CPU: MIPS R14000 Processor Chip Revision: 2.4
   

   FPU: MIPS R14010 Floating Point Chip Revision: 2.4
   

   Processor 7: 600 MHZ IP35
   

   CPU: MIPS R14000 Processor Chip Revision: 2.4
   

   FPU: MIPS R14010 Floating Point Chip Revision: 2.4
   

   Processor 8: 600 MHZ IP35
   

   CPU: MIPS R14000 Processor Chip Revision: 2.4
   

   FPU: MIPS R14010 Floating Point Chip Revision: 2.4
   

   Processor 9: 600 MHZ IP35
   

   CPU: MIPS R14000 Processor Chip Revision: 2.4
   

   FPU: MIPS R14010 Floating Point Chip Revision: 2.4
   

   Processor 10: 600 MHZ IP35
   

   CPU: MIPS R14000 Processor Chip Revision: 2.4
   

   FPU: MIPS R14010 Floating Point Chip Revision: 2.4
   

   Processor 11: 600 MHZ IP35
   

   CPU: MIPS R14000 Processor Chip Revision: 2.4
   

   FPU: MIPS R14010 Floating Point Chip Revision: 2.4
   

   CPU 0 at Module 001c07/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabl
   

   ed)
   

   Processor revision: 2.4. Scache: Size 8 MB Speed 300 Mhz  Tap 0xa
   

   CPU 1 at Module 001c07/Slot 0/Slice B: 600 Mhz MIPS R14000 Processor Chip (enabl
   

   ed)
   

   Processor revision: 2.4. Scache: Size 8 MB Speed 300 Mhz  Tap 0xa
   

   CPU 2 at Module 001c07/Slot 0/Slice C: 600 Mhz MIPS R14000 Processor Chip (enabl
   

   ed)
   

   Processor revision: 2.3. Scache: Size 8 MB Speed 300 Mhz  Tap 0xa
   

   CPU 3 at Module 001c07/Slot 0/Slice D: 600 Mhz MIPS R14000 Processor Chip (enabl
   

   ed)
   

   Processor revision: 2.3. Scache: Size 8 MB Speed 300 Mhz  Tap 0xa
   

   CPU 4 at Module 001c10/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabl
   

   ed)
   

   Processor revision: 2.4. Scache: Size 8 MB Speed 300 Mhz  Tap 0xa
   

   CPU 5 at Module 001c10/Slot 0/Slice B: 600 Mhz MIPS R14000 Processor Chip (enabl
   

   ed)
   

   Processor revision: 2.4. Scache: Size 8 MB Speed 300 Mhz  Tap 0xa
   

   CPU 6 at Module 001c10/Slot 0/Slice C: 600 Mhz MIPS R14000 Processor Chip (enabl
   

   ed)
   

   Processor revision: 2.4. Scache: Size 8 MB Speed 300 Mhz  Tap 0xa
   

   CPU 7 at Module 001c10/Slot 0/Slice D: 600 Mhz MIPS R14000 Processor Chip (enabl
   

   ed)
   

   Processor revision: 2.4. Scache: Size 8 MB Speed 300 Mhz  Tap 0xa
   

   CPU 8 at Module 001c13/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabl
   

   ed)
   

   Processor revision: 2.4. Scache: Size 8 MB Speed 300 Mhz  Tap 0xa
   

   CPU 9 at Module 001c13/Slot 0/Slice B: 600 Mhz MIPS R14000 Processor Chip (enabl
   

   ed)
   

   Processor revision: 2.4. Scache: Size 8 MB Speed 300 Mhz  Tap 0xa
   

   CPU 10 at Module 001c13/Slot 0/Slice C: 600 Mhz MIPS R14000 Processor Chip (enab
   

   led)
   

   Processor revision: 2.4. Scache: Size 8 MB Speed 300 Mhz  Tap 0xa
   

   CPU 11 at Module 001c13/Slot 0/Slice D: 600 Mhz MIPS R14000 Processor Chip (enab
   

   led)
   

   Processor revision: 2.4. Scache: Size 8 MB Speed 300 Mhz  Tap 0xa
   

   Main memory size: 6144 Mbytes
   

   Instruction cache size: 32 Kbytes
   

   Data cache size: 32 Kbytes
   

   Secondary unified instruction/data cache size: 8 Mbytes
   

   Memory at Module 001c07/Slot 0: 1024 MB (enabled)
   

   Bank 0 contains 512 MB (Standard) DIMMS (enabled)
   

   Bank 1 contains 512 MB (Standard) DIMMS (enabled)
   

   Memory at Module 001c10/Slot 0: 3072 MB (enabled)
   

   Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
   

   Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
   

   Bank 2 contains 512 MB (Standard) DIMMS (enabled)
   

   Bank 3 contains 512 MB (Standard) DIMMS (enabled)
   

   Memory at Module 001c13/Slot 0: 2048 MB (enabled)
   

   Bank 0 contains 512 MB (Standard) DIMMS (enabled)
   

   Bank 1 contains 512 MB (Standard) DIMMS (enabled)
   

   Bank 4 contains 512 MB (Standard) DIMMS (enabled)
   

   Bank 5 contains 512 MB (Standard) DIMMS (enabled)
   

   ROUTER in Module 001c07/Slot 0: Revision 1: Active Ports [1,2,3,4,6,] (enabled)
   

   ROUTER in Module 001c13/Slot 0: Revision 1: Active Ports [1,6,] (enabled)
   

   Integral SCSI controller 0: Version Fibre Channel QL2200A, 33 MHz PCI
   

   Disk drive: unit 1 on SCSI controller 0 (unit 1)
   

   Disk drive: unit 2 on SCSI controller 0 (unit 2)
   

   Integral SCSI controller 5: Version IEEE1394 SBP2
   

   IEEE1394 CDROM: node 1010031001c3c9 port 0 on SCSI controller 5
   

   IOC3/IOC4 serial port: tty3
   

   Graphics board: InfiniteReality3
   

   Graphics board: InfiniteReality3
   

   Integral Fast Ethernet: ef0, version 1, module 001c07, pci 4
   

   Iris Audio Processor: version RAD revision 13.0, number 1
   

   PCI Adapter ID (vendor 0x10a9, device 0x0002) PCI slot 0
   

   PCI Adapter ID (vendor 0x10a9, device 0x0002) PCI slot 1
   

   PCI Adapter ID (vendor 0x1077, device 0x2200) PCI slot 1
   

   PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 2
   

   PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
   

   PCI Adapter ID (vendor 0x11c1, device 0x5802) PCI slot 5
   

   PCI Adapter ID (vendor 0x104c, device 0x8009) PCI slot 6
   

   IOC3/IOC4 external interrupts: 1
   

   HUB in Module 001c07/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
   

   HUB in Module 001c10/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
   

   HUB in Module 001c13/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
   

   IP35prom in Module 001c07/Slot n0: Revision 6.210
   

   IP35prom in Module 001c10/Slot n0: Revision 6.210
   

   IP35prom in Module 001c13/Slot n0: Revision 6.210
   

   IEEE 1394 High performance serial bus controller 0: Type: OHCI, Version 0 0
   

   USB controller: type OHCI
   

   USB Human Interface Device: device id 0 type mouse

Code: Select all


   IRIS 3% /usr/gfx/gfxinfo -v
   

   Graphics board 0 is "KONAD" graphics.
   

   Managed (":0.0") 1920x1200
   

   Display has 2 channels
   

   4 GEs (of 4), occmask = 0x0f
   

   4MB external BEF ram, 32bit path
   

   2 RM10 boards (of 2) 1/1/0/0
   

   Texture Memory: 256MB/256MB/-/-
   

   Medium pixel depth
   

   32K cmap
   

   TVO option detected
   

   brd: 80f61806 3041606/3041606/-/- f9191002
   

   ge: 0 14832057 24731057 14231057
   

   rm0: 15032057 15431057
   

   4631057 2/2/2/2
   

   4d31057 2/2/2/2/2/2/2/2
   

   4938057 5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5
   

   rm1: 15032057 15431057
   

   4631057 2/2/2/2
   

   4d31057 2/2/2/2/2/2/2/2
   

   4938057 5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5
   

   dg: 05532057
   

   5838057 1/1/1/1
   

   5631057 1/1
   

   GE:   NIC #:      0000.0048.34ce (family: 0b)
   

   Serial #:   KJD735
   

   Part #:     030-1398-002
   

   KT:   NIC #:      0000.0059.08be (family: 0b)
   

   Serial #:   MHZ137
   

   Part #:     030-1593-001
   

   RM0:  NIC #:      0000.0058.dd9e (family: 0b)
   

   Serial #:   MJW797
   

   Part #:     030-1402-002
   

   TM0:  NIC #:      0000.0058.f45a (family: 0b)
   

   Serial #:   MJW847
   

   Part #:     030-1588-002
   

   RM1:  NIC #:      0000.0058.efb0 (family: 0b)
   

   Serial #:   MJW995
   

   Part #:     030-1402-002
   

   TM1:  NIC #:      0000.0058.ed8d (family: 0b)
   

   Serial #:   MJH033
   

   Part #:     030-1588-002
   

   RM2:  No NIC serial number available.
   

   TM2:  No NIC serial number available.
   

   RM3:  No NIC serial number available.
   

   TM3:  No NIC serial number available.
   

   BP:   No NIC serial number available.
   

   DG:   NIC #:      0000.004e.0a0e (family: 0b)
   

   Serial #:   LBR588
   

   Part #:     030-1242-001
   

   DGOPT:NIC #:      0000.004e.0aa8 (family: 0b)
   

   Serial #:   LBM153
   

   Part #:     030-1511-004
   

   Input Sync: Voltage - Video Level; Source - External; Genlocked - True
   

   Channel 0:
   

   Origin = (0,0)
   

   Video Output: 1920 pixels, 1200 lines, 23.98Hz (1920x1200_2398r2.vfo)
   

   Video Format Flags:  (none)
   

   Sync Output(s):
   

   Composite sync on Green
   

   Horizontal TTL sync on Aux 0
   

   Using Gamma Map 0
   

   Channel 2 (physical port 94):
   

   Origin = (0,60)
   

   Video Output: 1920 pixels, 1080 lines, 23.98Hz (HDGVO_1920x1080_2398psf
   

   .vfo)
   

   Video Format Flags:  (none)
   

   Sync Disabled
   

   Using Gamma Map 0
   

   Graphics board 1 is "KONAD" graphics.
   

   Managed (":0.1") 1920x1200
   

   Display has 2 channels
   

   4 GEs (of 4), occmask = 0x0f
   

   4MB external BEF ram, 32bit path
   

   2 RM10 boards (of 2) 1/1/0/0
   

   Texture Memory: 256MB/256MB/-/-
   

   Medium pixel depth
   

   32K cmap
   

   brd: 80f61806 3041606/3041606/-/- f9391002
   

   ge: 0 14832057 24731057 14231057
   

   rm0: 15032057 15431057
   

   4631057 2/2/2/2
   

   4d31057 2/2/2/2/2/2/2/2
   

   4938057 5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5
   

   rm1: 15032057 15431057
   

   4631057 2/2/2/2
   

   4d31057 2/2/2/2/2/2/2/2
   

   4938057 5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5/5
   

   dg: 05532057
   

   5838057 1/1/1/1
   

   5631057 1/1
   

   GE:   NIC #:      0000.0048.32c1 (family: 0b)
   

   Serial #:   KJD716
   

   Part #:     030-1398-002
   

   KT:   No NIC serial number available.
   

   RM0:  NIC #:      0000.0058.f220 (family: 0b)
   

   Serial #:   MJW997
   

   Part #:     030-1402-002
   

   TM0:  NIC #:      0000.0058.ed22 (family: 0b)
   

   Serial #:   MJH027
   

   Part #:     030-1588-002
   

   RM1:  NIC #:      0000.0058.d90e (family: 0b)
   

   Serial #:   MJH252
   

   Part #:     030-1402-002
   

   TM1:  NIC #:      0000.0058.ecb2 (family: 0b)
   

   Serial #:   MJH050
   

   Part #:     030-1588-002
   

   RM2:  No NIC serial number available.
   

   TM2:  No NIC serial number available.
   

   RM3:  No NIC serial number available.
   

   TM3:  No NIC serial number available.
   

   BP:   No NIC serial number available.
   

   DG:   NIC #:      0000.0058.de76 (family: 0b)
   

   Serial #:   MJD147
   

   Part #:     030-1055-001
   

   DGOPT:No NIC serial number available.
   

   Input Sync: Voltage - Video Level; Source - External; Genlocked - False

jan-jaap
Donor
From Wijchen, The Netherlands
Who joined June 17, 2004, 11:35 a.m.

Wrote the following at Dec. 5, 2008, 12:43 a.m...

Congratulations, that's a nice setup!

hirudin wrote:

Code: Select all
Memory at Module 001c07/Slot 0: 1024 MB (enabled) Memory at Module 001c10/Slot 0: 3072 MB (enabled) Memory at Module 001c13/Slot 0: 2048 MB (enabled)

You might want to distribute the memory evenly over the nodes, though.

Now this is a deep dark secret, so everybody keep it quiet

It turns out that when reset, the WD33C93 defaults to a SCSI ID of 0, and it was simpler to leave it that way... -- Dave Olson, in comp.sys.sgi
Currently in commercial service:

(2x)

In the museum : almost every MIPS/IRIX system.
Wanted : GM1 board for Professional Series GT graphics (030-0076-003, 030-0076-004)

bri3d
From Boulder, CO
Who joined June 28, 2008, 11:08 a.m.

Wrote the following at Dec. 5, 2008, 8:44 a.m...

Glad to see you got that beast up, pretty nice graphics too.

Agreed, though, you should try to distribute the memory as evenly as possible so that some CPUs aren't starved for RAM. Even memory distribution works best for most workloads.

<>

SGI: hinv

Onyx 3000, 12x600MHz, 6GB, dual-pipe IR3 with HD-GVO