Original spec when acquired, August 2011: R16K 700MHz, 1024MB RAM (4x256 standard), V10, 73GB HDs
UPDATE September 2011: replaced 73GB with two 146GB HDDs
UPDATE January 2012: RAM upgrade, soundcard
PCI cards are LSI 20320-HP, Creative SB0090 soundcard and Belkin F5U220 USB.
UPDATE September 2012: Belkin F5U503 Firewire card and 1TB external disk
LSI 21320 to replace LSI 20320-HP (for more usefully positioned sockets)
UPDATE May 2013: replaced V10 (030-1826-003 rev -A) with V12 (ex-Tezro)
UPDATE March 2014: tried Adaptec Duoconnect AUA-3020 without success -
UPDATE March 2014: replaced USB card with narrow SCSI socket cabled to Channel B on the LSI 21320, to drive a slide scanner (Nikon Coolscan II, seems fine with xsane from nekoware)
Hinv etc from May 2013 after fitting the V12:
hinv -vm
gfxinfo
The "GSM8704" is in this case a TV - 22LG3000 - connected using DVI-HDMI; my Pi uses the other HDMI input and there is also a VGA input for the Indigo2, RiscPC and EspressoPC. This replaced an Iiyama 9017 CRT when we got a new TV!
uname -aR reports "IRIX64 redbox 6.5 6.5.30m 07202013 IP35"
scsicontrol -v
The Syquest shows "Device is not ready" as there is no cartridge present - it seems to operate very nicely, mounting automatically when a cartridge is inserted and unmounting from the "Eject" option on the menu.
I also have a second 146GB drive fitted but only connect power when wanting to back up. The Fujitsu is set to spin up on command rather than power-on, so PROM-only operations can happen without wear on the drive (handy when fitting / troubleshooting other hardware!).
L1 info - for some reason I cannot get anything from "l1cmd pci" although I am sure this has worked in the past.
l1cmd flash status
l1cmd serial all
l1cmd env
The V10 used to run at 38C, so 44C after an hour's use (and the PIMM at 2C wamer) was a very slight concern, but the fans seem only slightly faster. It was January 2012 when I last put env output in this entry, quite possibly at night so the ambient temperature may have been several degrees lower (the Fuel is in a north-facing corner room). Checking again later, the V12 and PIMM were both down a couple of degrees AND the fans were slower, so I should stop worrying!
UPDATE September 2011: replaced 73GB with two 146GB HDDs
UPDATE January 2012: RAM upgrade, soundcard
PCI cards are LSI 20320-HP, Creative SB0090 soundcard and Belkin F5U220 USB.
UPDATE September 2012: Belkin F5U503 Firewire card and 1TB external disk
LSI 21320 to replace LSI 20320-HP (for more usefully positioned sockets)
UPDATE May 2013: replaced V10 (030-1826-003 rev -A) with V12 (ex-Tezro)
UPDATE March 2014: tried Adaptec Duoconnect AUA-3020 without success -
UPDATE March 2014: replaced USB card with narrow SCSI socket cabled to Channel B on the LSI 21320, to drive a slide scanner (Nikon Coolscan II, seems fine with xsane from nekoware)
Hinv etc from May 2013 after fitting the V12:
hinv -vm
Code: Select all
Location: /hw/module/001c01/node
IP34 Board: barcode NAS621 part 030-1707-003 rev -M
Location: /hw/module/001c01/node/cpubus/0
IP34PIMM Board: barcode MSY420 part 030-1891-001 rev -D
Location: /hw/module/001c01/Ibrick/xtalk/13
ODY128B1_2 Board: barcode NWM092 part 030-1884-005 rev -B
Location: /hw/module/001c01/Ibrick/xtalk/14
IP34 Board: barcode NAS621 part 030-1707-003 rev -M
Location: /hw/module/001c01/Ibrick/xtalk/15
IP34 Board: barcode NAS621 part 030-1707-003 rev -M
1 700 MHZ IP35 Processor
CPU: MIPS R16000 Processor Chip Revision: 2.1
FPU: MIPS R16010 Floating Point Chip Revision: 2.1
CPU 0 at Module 001c01/Slot 0/Slice A: 700 Mhz MIPS R16000 Processor Chip (enabled)
Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz Tap 0xa
Main memory size: 4096 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 4 Mbytes
Memory at Module 001c01/Slot 0: 4096 MB (enabled)
Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
Bank 2 contains 1024 MB (Premium) DIMMS (enabled)
Bank 3 contains 1024 MB (Premium) DIMMS (enabled)
Integral SCSI controller 6: Version IEEE1394 SBP2
Integral SCSI controller 7: Version LS1030, low voltage differential
Integral SCSI controller 8: Version LS1030, low voltage differential
Integral SCSI controller 0: Version QL12160, low voltage differential
Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL12160, single ended
CDROM: unit 4 on SCSI controller 1
Disk drive / removable media: unit 6 on SCSI controller 1
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V12
Integral Fast Ethernet: ef0, version 1, module 001c01, pci 4
Iris Audio Processor: version EMU revision A3, number 1
PCI Adapter ID (vendor 0x1033, device 0x0035) PCI slot 1
PCI Adapter ID (vendor 0x1033, device 0x0035) PCI slot 1
PCI Adapter ID (vendor 0x1033, device 0x00e0) PCI slot 1
PCI Adapter ID (vendor 0x1000, device 0x0030) PCI slot 2
PCI Adapter ID (vendor 0x1000, device 0x0030) PCI slot 2
PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
PCI Adapter ID (vendor 0x1102, device 0x0004) PCI slot 2
PCI Adapter ID (vendor 0x1102, device 0x7003) PCI slot 2
PCI Adapter ID (vendor 0x1102, device 0x4001) PCI slot 2
PCI Adapter ID (vendor 0x104c, device 0x8024) PCI slot 3
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
PCI Adapter ID (vendor 0x1045, device 0xc861) PCI slot 5
HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
IP35prom in Module 001c01/Slot n0: Revision 6.210
DMediaPro DM10 FW option: unit 0, revision 1.1.0
USB controller: type OHCI
USB controller: type OHCI
USB controller: type OHCI
gfxinfo
Code: Select all
Graphics board 0 is "ODYSSEY" graphics.
Managed (":0.0") 1920x1200
BUZZ version B.2
PB&J version 1
128MB memory
Banks: 4, CAS latency: 3
Monitor 0 type: GSM 8704
Channel 0:
Origin = (0,0)
Video Output: 1920 pixels, 1200 lines, 60.00Hz (1920x1200_60p.vfo)
The "GSM8704" is in this case a TV - 22LG3000 - connected using DVI-HDMI; my Pi uses the other HDMI input and there is also a VGA input for the Indigo2, RiscPC and EspressoPC. This replaced an Iiyama 9017 CRT when we got a new TV!
uname -aR reports "IRIX64 redbox 6.5 6.5.30m 07202013 IP35"
scsicontrol -v
Code: Select all
/dev/scsi/sc0d1l0: Disk FUJITSU MAP3147NP 5605
ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports: 16bit synch linkedcmds cmdqueing
Device is ready
/dev/scsi/sc1d4l0: CD-ROM TOSHIBA DVD-ROM SD-M14011007
ANSI vers 2, ISO ver: 0, ECMA ver: 0; supports: synch linkedcmds
Device is not ready
/dev/scsi/sc1d6l0: Disk SyQuest SQ3270S 3_05
ANSI vers 2, ISO ver: 0, ECMA ver: 0; supports: synch linkedcmds
Device is not ready
The Syquest shows "Device is not ready" as there is no cartridge present - it seems to operate very nicely, mounting automatically when a cartridge is inserted and unmounting from the "Eject" option on the menu.
I also have a second 146GB drive fitted but only connect power when wanting to back up. The Fujitsu is set to spin up on command rather than power-on, so PROM-only operations can happen without wear on the drive (handy when fitting / troubleshooting other hardware!).
L1 info - for some reason I cannot get anything from "l1cmd pci" although I am sure this has worked in the past.
l1cmd flash status
Code: Select all
Flash image A currently booted
Image Status Revision Built
----- ------------- ---------- -----
A user default 1.44.0 07/17/2006 18:20:38
B valid 1.44.0 07/17/2006 18:20:38
l1cmd serial all
Code: Select all
Data Location Value
------------------------------ ------------ --------
Local System Serial Number EEPROM 08:00:69:10:6F:CB
Local Brick Serial Number EEPROM NAS621
Reference Brick Serial Number NVRAM NAS621
EEPROM Product Name Serial Part Number Rev T/W
---------- -------------- ------------- -------------------- --- ------
NODE IP34 NAS621 030_1707_003 M 00
MAC MAC ADDRESS NA NA NA NA
PIMM IP34PIMM MSY420 030_1891_001 D 00
XIO ODY128B1_2 NWM092 030_1884_005 B 00
EEPROM JEDEC-SPD Info Part Number Rev Speed SGI
---------- ------------------------ ------------------ ---- ------ --------
DIMM 0 CE000000000000000C9B0F00 M3 46L2820DT2-CA0 2D 10.0 N/A
DIMM 2 CE0000000000000028181900 M3 46L2820BT1-CA0 0B 8.0 N/A
DIMM 1 CE000000000000000C5F0B00 M3 46L2820DT2-CA0 2D 10.0 N/A
DIMM 3 CE0000000000000027CE1400 M3 46L2820BT1-CA0 0B 8.0 N/A
l1cmd env
Code: Select all
Environmental monitoring is enabled and running.
Description State Warning Limits Fault Limits Current
-------------- ---------- ----------------- ----------------- -------
12V Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 12.063
12V IO Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 12.125
5V Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.096
3.3V Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.337
2.5V Enabled 10% 2.25/ 2.75 20% 2.00/ 3.00 2.470
1.5V Enabled 10% 1.35/ 1.65 20% 1.20/ 1.80 1.466
5V AUX Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.122
3.3V AUX Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.285
PIMM 12V BIAS Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 12.125
SRAM Enabled 10% 2.25/ 2.75 20% 2.00/ 3.00 2.522
VCPU Enabled 10% 1.13/ 1.38 20% 1.00/ 1.50 1.241
PIMM 1.5V Enabled 10% 1.35/ 1.65 20% 1.20/ 1.80 1.495
PIMM 3.3V AUX Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.285
PIMM 5V AUX Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.122
XIO 12V BIAS Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 11.938
XIO 5V Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.070
XIO 2.5V Enabled 10% 2.25/ 2.75 20% 2.00/ 3.00 2.457
XIO 3.3V AUX Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.285
Description State Warning RPM Current RPM
--------------- ---------- ----------- -----------
FAN 0 EXHAUST Enabled 920 1188
FAN 1 HD Enabled 1560 2280
FAN 2 PCI Enabled 1120 1562
FAN 3 XIO 1 Enabled 1600 2463
FAN 4 XIO 2 Enabled 1600 2376
FAN 5 PS Enabled 1349 3308
Advisory Critical Fault Current
Description State Temp Temp Temp Temp
----------------- ---------- --------- --------- --------- ---------
0 NODE 0 Enabled [Autofan Control] 80C/176F 35C/ 95F
1 NODE 1 Enabled [Autofan Control] 80C/176F 39C/102F
2 NODE 2 Enabled [Autofan Control] 80C/176F 28C/ 82F
3 PIMM Enabled [Autofan Control] 80C/176F 41C/105F
4 ODYSSEY Enabled [Autofan Control] 80C/176F 44C/111F
5 BEDROCK Enabled [Autofan Control] 85C/185F 39C/102F
The V10 used to run at 38C, so 44C after an hour's use (and the PIMM at 2C wamer) was a very slight concern, but the fans seem only slightly faster. It was January 2012 when I last put env output in this entry, quite possibly at night so the ambient temperature may have been several degrees lower (the Fuel is in a north-facing corner room). Checking again later, the V12 and PIMM were both down a couple of degrees AND the fans were slower, so I should stop worrying!