I was finally able to fulfill my childhood dream... (thanks Ian!)
hinv -vm
gfxinfo
I was running the display at 1600x1200 72Hz and 1920x1200 60Hz, but recently noticed that my Dell 24 inch monitor produces a much sharper image at 1280x1024, so I am at 1280x1024 50Hz now.
Great to be finally active here on Nekochan, instead of just lurking...
Goran
hinv -vm
Code:
Location: /hw/node
PM20360MHZ Board: barcode KXV166 part 030-1591-001 rev B
Location: /hw/node/xtalk/15
IP30 Board: barcode KVY335 part 030-1467-001 rev D
Location: /hw/node/xtalk/15/pci/2
FP1 Board: barcode KFJ675 part 030-0891-003 rev G
PWR.SPPLY.ER Board: barcode AAE1060374 part 060-0035-002 rev A
Location: /hw/node/xtalk/11
ODY128 Board: barcode KVS877 part 030-1404-003 rev A
2 360 MHZ IP30 Processors
Heart ASIC: Revision F
CPU: MIPS R12000 Processor Chip Revision: 3.5
FPU: MIPS R12010 Floating Point Chip Revision: 0.0
Main memory size: 1536 Mbytes
Xbow ASIC: Revision 1.4
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 2 Mbytes
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V8
Integral Fast Ethernet: ef0, version 1, pci 2
Iris Audio Processor: version RAD revision 12.0, number 1
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 3
PM20360MHZ Board: barcode KXV166 part 030-1591-001 rev B
Location: /hw/node/xtalk/15
IP30 Board: barcode KVY335 part 030-1467-001 rev D
Location: /hw/node/xtalk/15/pci/2
FP1 Board: barcode KFJ675 part 030-0891-003 rev G
PWR.SPPLY.ER Board: barcode AAE1060374 part 060-0035-002 rev A
Location: /hw/node/xtalk/11
ODY128 Board: barcode KVS877 part 030-1404-003 rev A
2 360 MHZ IP30 Processors
Heart ASIC: Revision F
CPU: MIPS R12000 Processor Chip Revision: 3.5
FPU: MIPS R12010 Floating Point Chip Revision: 0.0
Main memory size: 1536 Mbytes
Xbow ASIC: Revision 1.4
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 2 Mbytes
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V8
Integral Fast Ethernet: ef0, version 1, pci 2
Iris Audio Processor: version RAD revision 12.0, number 1
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 3
gfxinfo
Code:
Graphics board 0 is "ODYSSEY" graphics.
Managed (":0.0") 1280x1024
BUZZ version A.1
PB&J version 1
128MB memory
Banks: 4, CAS latency: 3
Monitor 0 type: Unknown
Input Sync: Voltage - Video Level; Source - Internal; Genlocked - False
Channel 0:
Origin = (0,0)
Video Output: 1280 pixels, 1024 lines, 50.00Hz (1280x1024_50)
Video Format Flags: (none)
Sync Disabled
Using Gamma Map 0
Managed (":0.0") 1280x1024
BUZZ version A.1
PB&J version 1
128MB memory
Banks: 4, CAS latency: 3
Monitor 0 type: Unknown
Input Sync: Voltage - Video Level; Source - Internal; Genlocked - False
Channel 0:
Origin = (0,0)
Video Output: 1280 pixels, 1024 lines, 50.00Hz (1280x1024_50)
Video Format Flags: (none)
Sync Disabled
Using Gamma Map 0
I was running the display at 1600x1200 72Hz and 1920x1200 60Hz, but recently noticed that my Dell 24 inch monitor produces a much sharper image at 1280x1024, so I am at 1280x1024 50Hz now.
Great to be finally active here on Nekochan, instead of just lurking...
Goran
_________________
- R12k 2x360 MHz, V8, 1.5 GB RAM, 73 GB HD